Owner's Manual - Roland

More documents

Recommendations

Info

Chapter 8. System Settings and MIDI Applications Synchronization with an External MIDI Device Timing of the D2’s sequencer can be synchronized with that of another sequencer for playback. This feature enables largescale performance playing back a number of parts at the same time. Making an external MIDI sequencer synchronized with playback on the D2 Now, let’s make D2’s patterns synchronized with an external MIDI sequencer. (In this example, the external MIDI sound generator is played back using the MIDI data from the external MIDI sequencer.) Set up the D2 1. Set SYNC OUT to “ON” (p. 74). This setting enables synchronizing signals to be transmitted from the D2’s MIDI OUT. 2. Set the sequence output assignment for all parts of the pattern to be used to “INT” (p. 19). This setting enables the D2 to output only MIDI clocks and start/stop information from the MIDI OUT connector. Set up the external sequencer 3. Set the external MIDI sequencer so it will synchronize to the MIDI Clock messages that it receives. For details on the setting, refer to the owner’s manual for your MIDI sequencer. Start synchronized playback. 4. Press the [ ] button of the D2, and synchronized playback will begin. 5. To stop synchronized playback, press [ on the D2. The external MIDI sequencer will also stop. ] button 80 MIDI IN MIDI OUT Sequencer D2 Making the D2 synchronized with performance on an external sequencer. The playback of the D2’s sequencer can be synchronized to the MIDI Clock messages transmitted from an external MIDI sequencer or from a hard disk recorder (optional). In the following example, we will synchronize the D2 pattern playback to an external source of timing. MIDI OUT Set up the D2. MIDI IN Sequencer D2 1. Set SYNC MODE to “SLAVE” (p. 74). 2. Press the [ ] button on the D2. Returns to the beginning of pattern. Set up the external sequencer. 3. Set up so that MIDI clocks are transmitted from the external MIDI sequencer. For details on the setting, refer to the owner’s manual for your external MIDI sequencer. Start synchronized playback. 4. Press the [PLAY] button of the external MIDI sequencer, and synchronized playback will begin. 5. To stop synchronized playback, press [STOP] button on the external sequencer. * As required, set up to block transmission of playback information from the external device to the D2. (Or, set MIDI channels 1 to 7 and 10, corresponding to those used on the D2, not to be used for data transmission.) Otherwise, the D2 performs playback with playback information from the external device. For details, see the operation manual of the external MIDI device. * It is also possible to control playback/stop operations only without synchronization with MIDI clocks transmitted from the external MIDI sequencer. In this case, set Sync mode of the D2 to “REMOTE.”
Saving data on an external sequencer (Bulk Dump) Data for the currently selected pattern or for all data in memory can be transmitted from the D2 to another D2, or to an external MIDI sequencer (such as the <strong>Roland</strong> MC-80) for saving. Transmitting this data is called bulk dump, and receiving this data is called bulk load. Transmission (bulk dump) procedure Here’s how data stored in the D2 can be transmitted to a sequencer or other external MIDI device for saving. fig.8-7.j MIDI IN MIDI OUT Sequencer 1. Press [SYSTEM] several times to access the MIDI transmission setting display. 2. Press [ENTER] to access the Bulk Dump setting display. 3. Turn [VALUE] to select either “Ptn” (transmit the data of the current pattern) or “ALL” (transmit all data). 4. Press [ENTER]. The display will ask “SurE” (are you sure you want to proceed with the transmission?) * To cancel the operation, press [EXIT]. 5. Set your connected MIDI device so it is ready to receive data. 6. Press [ENTER] to begin the transmission. Once the data transmission has been completed, the previous display will reappear. Chapter 8. System Settings and MIDI Applications D2 Reception (bulk load) procedure Here’s how to receive data that was stored on an external MIDI device. fig.8-8.j MIDI OUT 1. Press [SYSTEM] several times to access the MIDI reception setting display. 2. Press [ENTER] several times to access the Bulk Load setting display. 3. Turn [VALUE] to select either “Ptn” (receive the data of the current pattern) or “ALL” (receive all data). 4. Press [ENTER]. The display will ask “SurE” (are you sure you want to proceed with the reception?). * To cancel the operation, press [EXIT]. MIDI IN Sequencer D2 5. Press [ENTER] and reception will begin. 6. Transmit data from the connected MIDI device. Once the data reception has been completed, the previous display will reappear. When you enter Bulk Load, the contents of the pattern being editing will be changed. If you selected “ALL” in step 3, all of the data will be changed. Never turn off the power while bulk load is in progress. Doing so may destroy the contents of memory. 81 Chapter 8
Page 1 and 2:
Thank you, and congratulations on y
Page 3 and 4:
011 • Do not allow any objects (e
Page 5 and 6:
Contents IMPORTANT NOTES ..........
Page 7 and 8:
Contents Chapter 8. System Settings
Page 9 and 10:
How to read this manual The D2 manu
Page 11 and 12:
Rear panel Panel Descriptions/ Maki
Page 13 and 14:
How characters and numerals are dis
Page 15 and 16:
Chapter 2. Playing Patterns Basics
Page 17 and 18:
Muting individual rhythm sounds The
Page 19 and 20:
Modifying the settings of each part
Page 21 and 22:
Chapter 3. About the D-FIELD What i
Page 23 and 24:
SOUND mode Playing back a phrase (R
Page 25 and 26:
Chapter 3. About the D-FIELD Applyi
Page 27 and 28:
Playing arpeggios (ASSIGN 1: ARPEGG
Page 29 and 30: Beat pattern Chapter 3. About the D
Page 31 and 32: Chapter 3. About the D-FIELD Auditi
Page 33 and 34: XY mode Chapter 3. About the D-FIEL
Page 35 and 36: Making detailed settings 1. Hold do
Page 37 and 38: Chapter 3. About the D-FIELD Changi
Page 39 and 40: Changing the reverb depth (ASSIGN 2
Page 41 and 42: Sounding a snare roll (SD ROLL) Cha
Page 43 and 44: Delay (Add echoes to the sound) Cha
Page 45 and 46: Chapter 4. Applying Effects to the
Page 47 and 48: 5. Distortion (Distort the Sound Se
Page 49 and 50: 9. Phonograph (Simulates an Old Rec
Page 51 and 52: 14. Phaser (Modulate the Sound) Cha
Page 53 and 54: 18. Flanger (Add Metallic Resonance
Page 55 and 56: Chapter 4. Applying Effects to the
Page 57 and 58: 24. Gate Reverb (Sharply Cut the Re
Page 59 and 60: Chapter 5. Replacing phrases to cre
Page 61 and 62: The display during realtime recordi
Page 63 and 64: Inputting notes Changing the locati
Page 65 and 66: Editing a pattern (Pattern Edit) Th
Page 67 and 68: Erasing unwanted data (Erase) fig.P
Page 69 and 70: Chapter 7. Playing and Creating Son
Page 71 and 72: Inserting a step (Step Insert) You
Page 73 and 74: Chapter 8. System Settings and MIDI
Page 75 and 76: RPS TRIGGER QUANTIZE Chapter 8. Sys
Page 77 and 78: MIDI reception settings Chapter 8.
Page 79: Using the D2 together with an exter
Page 83 and 84: Error Message List If the D2 is ope
Page 85 and 86: No. Name 065 Timpani 066 Steel Drum
Page 87 and 88: Note No. 35 C2 36 38 40 41 43 45 47
Page 89 and 90: Note No. 35 C2 36 38 40 41 43 45 47
Page 91 and 92: Note No. 35 C2 36 38 40 41 43 45 47
Page 93 and 94: No. Pattern Name BPM Mes. Programme
Page 95 and 96: RPS Set List D-FIELD No. Pattern Na
Page 97 and 98: Waveform List Group A No Name No Na
Page 99 and 100: ● Program Change status 2nd byte
Page 101 and 102: ❍Hold 2 (Controller number 69) st
Page 103 and 104: ●Start status FAH * This message
Page 105 and 106: ■1-3.Patch +———————
Page 107 and 108: 6. Supplementary material ■Exampl
Page 109 and 110: goovebox (Sequencer Section) Model
Page 111 and 112: Index Numerics 4 Band EQ ..........
Page 113 and 114: MEMO
Page 115 and 116: This product complies with the requ
show all

Owner's Manual - Roland

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?