SMCD3G Cable Modem Gateway User Manual

More documents

Recommendations

Info

Installing Your Gateway Figure 4. Connecting the Gateway to the a Laptop or Desktop Computer Connecting the WAN To connect your Gateway to a Wide Area Network (WAN) interface: 1. Connect a coaxial cable to the port labeled Cable on the rear panel of the Gateway from a cable port in your home or office (see Figure 2 on page 13). Use only manufactured coaxial patch cables with F-type connectors at both ends for all connections. 2. Hand-tighten the connectors to secure the connection. 3. If the modem was not installed by your cable provider (ISP) or is replacing another cable modem, contact your cable operator to register the SMCD3G. If the modem is not registered with your cable operator, it will be unable to connect to the cable network system. Powering on the Gateway After making your LAN and WAN connections, use the following procedure to power on the Gateway: 1. Connect the supplied power adapter to the port labeled 12VDC on the rear panel of the Gateway (see Figure 2 on page 13). 2. Connect the other end of the power adapter to a working power outlet. The Gateway powers on automatically, the POWER LED on the front panel goes ON, and the other front panel LEDs show the Gateway’s status (see Table 1 on page 12). WARNING: Only use the power adapter supplied with the Gateway. Using a different power adapter can damage your Gateway and void the warranty. 16 SMCD3G Cable Modem Gateway User Manual
3 Configuring Your Computer for TCP/IP After you install your SMCD3G Cable Modem Gateway, configure the TCP/IP settings on a computer that will be used to configure your Gateway. This chapter describes how to configure TCP/IP for various Microsoft Windows and Apple Macintosh operating systems. The topics covered in this chapter are: � Configuring Microsoft Windows 2000 (page 18) � Configuring Microsoft Windows XP (page 19) � Configuring Microsoft Windows Vista (page 20) � Configuring an Apple® Macintosh® Computer (page 22) 17 SMCD3G Cable Modem Gateway User Manual
Page 2 and 3: SMC Networks 20 Mason Irvine, CA. 9
Page 4 and 5: Contents System Settings Menu......
Page 6 and 7: Key Features Preface The following
Page 8 and 9: Typographic Conventions Preface Thi
Page 10 and 11: Unpacking Package Contents Getting
Page 12 and 13: Getting to Know Your Gateway Table
Page 14 and 15: 2 Installing Your Gateway This chap
Page 18 and 19: Configuring Your Computer for TCP/I
Page 24 and 25: Pre-configuration Guidelines Before
Page 26 and 27: Configuring Your Gateway Accessing
Page 28 and 29: Configuring Your Gateway Web Manage
Page 30 and 31: Password Settings Menu Configuring
Page 32 and 33: LAN Settings Menu Configuring Your
Page 34 and 35: Configuring Your Gateway 4. To conf
Page 36 and 37: Configuring Your Gateway 5. To chan
Page 38 and 39: Security Settings (Firewall) Menu C
Page 40 and 41: Configuring Your Gateway 4. Click A
Page 42 and 43: Configuring Your Gateway Defined Ac
Page 44 and 45: Configuring Your Gateway 5. To defi
Page 46 and 47: Configuring Your Gateway Figure 25.
Page 48 and 49: To enable port triggering: Configur
Page 50 and 51: Configuring Your Gateway Table 13.
Page 52 and 53: Configuring Schedule Rules Configur
Page 54 and 55: Configuring Email Alerts Configurin
Page 56 and 57: Configuring DMZ Settings Configurin
Page 58 and 59: Viewing Status Information Configur
Page 60 and 61: Standards � 802.3 10BaseT Etherne
Page 62 and 63: Transmitter � Modulation: - TDMA:
Page 64 and 65: FCC Interference Statement Appendix
Page 66 and 67:
Index F L Factory defaults LAN conn
show all

SMCD3G Cable Modem Gateway User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?