Pure-Flo®

More documents

Recommendations

Info

74 GENERAL ENGINEERING DATA VALVE END CONNECTIONS For ease in identification, each valve body is stamped with the letter designation of the appropriate end connection. END CONNECTION CODE Acme Sanitary Threads (male w/45° Chamfer Seat) F1 Acme Sanitary Threads (male w/Gasket Seat) F2 Buttweld (12 Gauge) Z Buttweld (14 Gauge) G Buttweld (16 Gauge) H Buttweld (18 Gauge) L Buttweld (20 Gauge) M Buttweld (sch. 5) P Buttweld (sch. 10) R Buttweld (sch. 40) S Cherry-Burrell Quick Clamp C Cherry Burrell “I” Clamp (male) D Cherry Burrell “I” Clamp (female) E DIN 11850 Series # 1 T1 DIN 11850 Series #2 T2 DIN 11850 Series #3 T3 ISO 1.0 Wall Thk. T ISO 1.6 Wall Thk. U ISO 2.0 Wall Thk. V ISO 2.3 Wall Thk. W ISO 2.6 Wall Thk. X ISO 2.9 Wall Thk. XX SMS V V Superior Stainless, Quick Connect Klamp J Tri-Clover Tri-Clamp* B Tri-Clover Tri-Clamp* (Sch. 5) N Valex, Val-line K *A registered Trademark of Tri-Clover Inc. INTERIOR VALVE FINISHES ITT recommends specifying a maximum surface roughness in micro inches (μin) or microns (μm). This assures all points on the valve surface will be equal to or less than the specified roughness value. Foundry Finish (Investment Castings) 170–180μin* 4.32–4.57 μm* Satin Finish 75 μin* 1.91 μm* #4 Polish 35 μin 0.89 μm #150 Grit Polish 35 μin 0.89 μm #180 Grit Polish 25 μin 0.64 μm #240 Grit Polish 20 μin 0.51 μm #320 Grit Polish 11 μin 0.28 μm Electropolish A reverse plating process that brightens the metal by removing a portion of the original surface. Glass Lined Available in sizes from 1/2"–8" (FDA compliant).** PVDF Lined Polypropylene Lined Available in sizes from 3/4"–8" (FDA compliant).** Available in sizes from 3/4"–8" (FDA compliant).** *The above roughness height is approximate and should only be used as a guide. **Available in flanged end connections only. VALVE STROKE VALVE SIZE FULL STROKE Bio-Tek 0.16" 0.50" 0.25" DN 15 6.3 mm 0.75" 0.38" DN 20 9.6 mm 1.00" 0.50" DN 25 12.7 mm 1.50" 0.81" DN 40 20.6 mm 2.00" 1.12" DN 50 28.4 mm 3.00" 1.62" DN 80 41.3 mm 4.00" 2.12" DN 100 53.8 mm
GENERAL ENGINEERING DATA PRESSURE/TEMPERATURE RECOMMENDA- The above chart does not pertain to steam or corrosive services. Please consult our Service and Engineering Catalog for particular service recommendations. For services exceeding these pressure/temperature recommendations, consult the factory. PTFE DIAPHRAGMS FOR VACUUM SERVICE Notes: 1. Service conditions falling to the right of these lines will require bonnet evacuation. 2. PTFE-Diaphragms, 6" (DN 150) size and larger, will not withstand full vacuum at any temperature unless bonnets are evacuated. 3. With evacuated bonnets any size PTFE-Diaphragms can be used up to 350°F (176°C). 75 GENERAL ENGINEERING DATA
Page 1 and 2:
Pure-Flo ® Diaphragm Valves High P
Page 3 and 4:
ITT Fluid Technology Corporation, U
Page 5 and 6:
3 INNOVATION
Page 7 and 8:
T he integration of innovative qual
Page 9 and 10:
FEATURES BENEFITS Adjustable Travel
Page 11 and 12:
MANUFACTURING METHODS Castings: Pur
Page 13 and 14:
ELECTROPOLISHING Electropolishing,
Page 15 and 16:
BODY DIMENSION CHARTS ISO & DIN ISO
Page 17 and 18:
PURE-FLO ® GMP ® 15 The GMP (Good
Page 19 and 20:
PURE-FLO ® BIO-TEK ® ® PURE-FLO
Page 21 and 22:
PURE-FLO ® ZERO STATIC “T” WIT
Page 23 and 24:
MODULAR VALVE ASSEMBLIES 21 21 The
Page 25 and 26: “TM” & #16 DIAPHRAGMS The intro
Page 27 and 28: BONNETS SIZE RANGE 1/2"-4"(DN 15-10
Page 29 and 30: MODULAR VALVE ASSEMBLIES LIST OF PA
Page 31 and 32: DIAPHRAGM DRIVEN Diaphragm-driven t
Page 33 and 34: 3”-4” SERIES 47 ADVANTAGE ® AC
Page 35 and 36: MODULAR VALVE ASSEMBLIES AIR TO OPE
Page 37 and 38: ADVANTAGE ® ACTUATOR A100 DIRECT A
Page 39 and 40: ADVANTAGE ® ACTUATOR A300 37 DOUBL
Page 41 and 42: ADVANTAGE ® ACTUATOR WEIGHTS & MEA
Page 43 and 44: ADVANTAGE ® SWITCH PACKAGE SP-2 41
Page 45 and 46: ADVANTAGE ® SWITCH PACKAGE SP-2.5
Page 47 and 48: ADVANTAGE ® SWITCH PACKAGE SP-3.0
Page 49 and 50: MANUAL BONNET SWITCH PACKAGE 2” P
Page 51 and 52: WFI POINT-OF-USE SCHEMATIC COLD Not
Page 53 and 54: ADVANTAGE ® ACTUATOR WITH POSITION
Page 55 and 56: FINE THROTTLING ; ;; ; ; ;; ; ; ; ;
Page 57 and 58: DIAPHRAGM GRADE TEMPERATURE MATERIA
Page 59 and 60: 1 Thermoplastic PAS (polyarylsulfon
Page 61 and 62: 1/2” TRI-CLAMP X SWICKLE BODY 3/8
Page 63 and 64: “Our customers have been more tha
Page 65 and 66: Valve Size A B C D E F G H I J Inch
Page 67 and 68: PURE-FLO ® DIVERT VALVES The paten
Page 69 and 70: LINE DRAWINGS 2-WAY DIVERT VALVE TO
Page 71 and 72: PURE-FLO ® INTEGRAL CHROMATOGRAPHY
Page 73 and 74: TOP VIEW SIDE VIEW FRONT VIEW TOP V
Page 75: GENERAL ENGINEERING DATA VALVE SIZE
Page 79 and 80: COMPLIANCE, APPROVALS AND VALIDATIO
Page 81 and 82: Bonnet isolation, streamlined fluid
Page 83 and 84: BONNET OPTIONS, DIAPHRAGMS, AND ACT
Page 85 and 86: FABRICATION TYPE (Block BI) Code De
Page 87 and 88: FIGURE NUMBERS 85 TYPE OF VALVE Opt
Page 89 and 90: FIGURE NUMBERS MULTIPORT VALVE TOPW
Page 91 and 92: STANDARD PURE-FLO FIGURE NUMBER BLO
Page 93 and 94: 88 TERMS AND CONDITIONS OF SALE CON
show all

Pure-Flo®

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?