Bedienungsanleitung euro-Maus 4 Version 2012 ... - ROPA Fahrzeug

8 Störung und Abhilfe
ADM3 fault
code (J1939)
SPN / FMI
Kapitel 8
Störung und Abhilfe
ADM3
fault code
(K-line)
MR2
fault code
(K-line)
729 / 12 - 16432
354
9. Fault codes
Fault location Fault description Remedial action Pin
Intake Air Heater
(PLD/MR2)
730 / 0 13900 - Output Relay 2 (REL 2)
730 / 1 13901 - Output Relay 2 (REL 2)
730 / 2 13902 - Output Relay 2 (REL 2)
730 / 3 13903 - Output Relay 2 (REL 2)
730 / 4 13904 - Output Relay 2 (REL 2)
Circuit Universal Troubles
Grid Heater: No
Increasing Boost
Temperature After
Activation
Relay Permanently
Closed (Grid Heater)
Relay Permanently Open
(Grid Heater)
Voltage too High when
Activated
Voltage too Low when
Activated
870 / 3 - 14223 SCR Diffusor Heating Circuit High
870 / 3 - 14270
Heater Regeneration
System
Circuit High
870 / 4 - 14222 SCR Diffusor Heating Circuit Low
870 / 4 - 14269
Heater Regeneration
System
Circuit Low
870 / 5 - 14221 SCR Diffusor Heating Circuit Open
904 / 9 18809 - Front Axle Speed Abnormal Update Rate
904 / 19 18819 - Front Axle Speed
925 / 3 - 17905
925 / 4 - 17908
973 / 9 18909 -
973 / 19 18919 -
974 / 2 14202 -
974 / 3 14203 -
974 / 4 14204 -
SCR Module Proportional
Valve Bank
SCR Module Proportional
Valve Bank
Engine Retarder
Selection
Engine Retarder
Selection
Remote Throttle Pedal
(HFG)
Remote Throttle Pedal
(HFG)
Remote Throttle Pedal
(HFG)
Received Network Data
in Error
Circuit High
Circuit Low
Abnormal Update Rate
Received Network Data
in Error
Supply Voltage Out of
Range (Pin HFG+)
Voltage too High
Voltage too Low
986 / 1 - 10631 Fan Speed Speed Too Low
986 / 9 - 10612 Fan Speed Time Out
986 / 9 - 17112 Fan Speed Time Out
1004 / 3 14403 - Output Relay 4 (REL 4) Open Circuit
1004 / 4 14404 - Output Relay 4 (REL 4) Short Circuit to Ground
1005 / 3 14503 -
1005 / 4 14504 -
Output PWM Pedal
Supply or Transmission
(FP+)
Output PWM Pedal
Supply or Transmission
(FP+)
- Check wiring
- Check relay 2
- Check grid heater
- Check wiring
- Check relay 2
- Check wiring
- Check relay 2
LSCAN-
MR
ADM3 operating manual rev. 10.00b 161 / 226
15/09
15/09
15/09
- Check wiring 15/09
- Check wiring
- Check relay 2
- Limit values for the supply
voltage of the
HFG:
Minimum value: 4,8 V and
maximum value: 5,2 V.
- Check wiring
- Check remote pedal
- Check wiring
- Check remote pedal
- Check wiring
- Check relay 4
- Check wiring
- Check relay
15/09
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
CAN-
J1939
CAN-
J1939
LSCAN-
MR
LSCAN-
MR
CAN-
J1939
CAN-
J1939
18/17
18/18
18/18
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
18/01
18/01
Open Circuit - Check wiring. 15/05
Short Circuit to Ground - Check wiring. 15/05