TPT User's Guide - PikeTec

More documents

Recommendations

Info

Page 54 TPT User’s Guide The first column takes the names of an input or output channel respectively. Note, that channels may only contain alphanumerical characters and the underline. Due to this restriction, channel names must sometimes differ from the source code’s original variable, e.g. if the code variable is contained in a structure. In those cases, the variables original C-Code variable may be stated in the second column. Furthermore you may specify the type of the C code variable. The C-Code Type must be one of the following TPT C-code types which are equivalent to the ANSI C-types which can be found in the table below: TPT C-code type ANSI C-type uint8 unsigned char int8 signed char uint16 unsigned short int16 signed short uint32 unsigned int int32 signed int int64 long long float float double double bool unsigned char The last two columns take optional scaling information for a given channel. It is assumed, that scaling is applied using the polynomial form: physical = fixed * slope + bias When both, a slope and a bias are given for a channel, reading and writing that channel will also include scaling values from its physical representation to its fixed-point representation and vice versa. Parameters that are to be accessed within the executable are configured in just the same way. Have a look at the “Parameters” sheet, if you want to exchange and use system parameters. As soon as you have filled the MS Excel Sheet with all information needed, you can return to the Exe-Platform configuration dialog and use the button “Generate test driver C code”, in order to finally generate a test-frame to the specified function. TPT will read in the Excel file and create a C source file based on the information found. You should now be able to build an executable file from the generated source code using an arbitrary compiler and linker. If this fails, please also check, that all information you gave within the Excel file are correct. The resulting executable file is ready to be run with the Exe-Platform. Just configure the platform with the correct command line and run your tests against the C-code. 9.5 Standalone platform The standalone platform is not really a test execution platform because the system under test will not be stimulated and no outputs from the system are inputs to TPT. The standaloneplatform is more the execution of the test cases in TPT for debugging of the tests without having the connection to the system under test. The inputs in TPT will be set to constant default values. Thus this is more a simulation than a real test.
TPT User's Guide Page 55 10 Test Execution 10.1 Introduction Tests can be executed after setting up test, test-configurations and platform configuration. The test execution runs a test set on the different platforms. 10.2 Test execution configuration Figure 38 shows the test execution configuration.
Page 1 and 2:
TPT User's Guide Version 3.1 13 Feb
Page 3 and 4: TPT User's Guide Page 3 5 Modelling
Page 5 and 6: TPT User's Guide Page 5 1 Introduct
Page 7 and 8: TPT User's Guide Page 7 1.1.6 Speci
Page 9 and 10: TPT User's Guide Page 9 1.2.5 Menu
Page 11 and 12: TPT User's Guide Page 11 2.3 Creati
Page 13 and 14: TPT User's Guide Page 13 3 Signatur
Page 15 and 16: TPT User's Guide Page 15 4 Graphica
Page 17 and 18: TPT User's Guide Page 17 initial no
Page 19 and 20: TPT User's Guide Page 19 4.7 Creati
Page 21 and 22: TPT User's Guide Page 21 Figure 10:
Page 23 and 24: TPT User's Guide Page 23 To create
Page 25 and 26: TPT User's Guide Page 25 You will b
Page 27 and 28: TPT User's Guide Page 27 5.2 Defini
Page 29 and 30: TPT User's Guide Page 29 6 Definiti
Page 31 and 32: TPT User's Guide Page 31 each state
Page 33 and 34: TPT User's Guide Page 33 The rules
Page 35 and 36: TPT User's Guide Page 35 7 Organisa
Page 37 and 38: TPT User's Guide Page 37 _ Figure 2
Page 39 and 40: TPT User's Guide Page 39 8 Test set
Page 41 and 42: TPT User's Guide Page 41 9 Platform
Page 47 and 48: TPT User's Guide Page 47 9.3.1.1 Ex
Page 49 and 50: TPT User's Guide Page 49 9.4 The ex
Page 51 and 52: TPT User's Guide Page 51 tpt_vmapi_
Page 53: TPT User's Guide Page 53 For now, l
Page 57 and 58: TPT User's Guide Page 57 Platforms
Page 59 and 60: TPT User's Guide Page 59 11 Test An
Page 61 and 62: TPT User's Guide Page 61 A toolbar
Page 63 and 64: TPT User's Guide Page 63 11.3.1 Rep
Page 69 and 70: TPT User's Guide Page 69 13 Functio
Page 71 and 72: TPT User's Guide Page 71 13.3.3 Asy
Page 73 and 74: TPT User's Guide Page 73 14 Debuggi
Page 79 and 80: TPT User's Guide Page 79 Activates/
Page 83 and 84: TPT User's Guide Page 83 15.7 The l
Page 85 and 86: TPT User's Guide Page 85 15.10 Envi
Page 87 and 88: TPT User's Guide Page 87 is 0 if an
Page 89 and 90: 16 Index add unambiguous variants .
Page 91: TPT User's Guide Page 91 shortcuts
show all

TPT User's Guide - PikeTec

Create successful ePaper yourself

Delete template?

Save as template?