Programmer's Manual TSP700/800 Series - i-POS.nl BV

More documents

Recommendations

Info

Commands to Control Peripheral Devices FUNCTION Define drive pulse width for peripheral device CODE n1 n2 HEX 1B 07 n1 n2 REMARKS Defines the drive pulse width for peripheral devices requiring other than standard 200 ms pulse time and delay time. n1 indicates the energizing time and n2 indicates the delay time, using 10ms units. FUNCTION Control peripheral device #1 CODE HEX 07 REMARKS Executes drive pulse for peripheral device #1. FUNCTION Control peripheral device #1 CODE HEX 1C REMARKS Executes drive pulse for peripheral device #1. FUNCTION Control peripheral device #2 CODE HEX 19 REMARKS Drives peripheral device #2. The drive pulse width and delay time are fixed at 200 ms. FUNCTION Control peripheral device #2 CODE HEX 1A REMARKS Drives peripheral device #2. The drive pulse width and delay time are fixed at 200 ms. – 35 – LINE MODE
LINE MODE Commands to Control Auto Cutter FUNCTION Cut command to the auto cutter CODE “d” n HEX 1B 64 n REMARKS n = “0” or : Cuts the paper fully immediately. n = “1” or : Cuts the paper leaving one point uncut immediately. n = “2” or : Cuts the paper fully after feeding the paper to the cutting position. When print start position detect is ON, feeds the paper to the next print start position first, feeds the paper to the cutting position, then cuts the paper fully. n = “3” or : Cuts the paper fully after feeding the paper to the cutting position. When print start position detect is ON, feeds the paper to the next print start position first, feeds the paper to the cutting position, then cuts the paper leaving one point uncut. – 36 –
Page 1 and 2: Thermal Printer TSP700 Series TSP80
Page 3 and 4: TABLE OF CONTENTS 1. OUTLINE.......
Page 5 and 6: LINE MODE 2-1. Command Summary The
Page 7 and 8: LINE MODE Commands to Print Dot Gra
Page 9 and 10: LINE MODE 2-2. Command Specificatio
Page 11 and 12: LINE MODE CODE 39, NW-7, ITF CODE 3
Page 13 and 14: LINE MODE Express “% (25H)” as
Page 15 and 16: LINE MODE FUNCTION CODE HEX 0E Set
Page 17 and 18: LINE MODE FUNCTION Upperlining CODE
Page 19 and 20: LINE MODE Commands to Set the Page
Page 21 and 22: LINE MODE Commands to Move the Prin
Page 23 and 24: LINE MODE FUNCTION One time n/8 mm
Page 25 and 26: LINE MODE FUNCTION Alignment CODE
Page 27 and 28: LINE MODE EXAMPLE We will create th
Page 29 and 30: LINE MODE EXAMPLE We will create th
Page 31 and 32: LINE MODE EXAMPLE MSB LSB MSB LSB d
Page 33 and 34: LINE MODE FUNCTION Define logo data
Page 35 and 36: LINE MODE FUNCTION Print logo image
Page 37: LINE MODE FUNCTION Data Binary Hexa
Page 41 and 42: LINE MODE 2) Use N=3 for folloing s
Page 43 and 44: LINE MODE FUNCTION Initialize print
Page 45 and 46: LINE MODE Number of transmit byte n
Page 47 and 48: LINE MODE FUNCTION Printer status #
Page 49 and 50: PAGE MODE Other commands Control co
Page 51 and 52: PAGE MODE FUNCTION Define ruled lin
Page 53 and 54: PAGE MODE Character rotation and ch
Page 55 and 56: PAGE MODE Bar code rotation Start p
Page 57 and 58: PAGE MODE FUNCTION Set bar code dat
Page 59 and 60: PAGE MODE FUNCTION Copy BMP file to
Page 61 and 62: PAGE MODE Other commands FUNCTION P
Page 63 and 64: PAGE MODE Parameter n1 n2 n3 n4 n4
Page 65 and 66: PAGE MODE FUNCTION Request status C
Page 67 and 68: PAGE MODE Version No. n Header #2 1
Page 69 and 70: PAGE MODE FUNCTION Set status trans
Page 71 and 72: DP8340 MODE 4-1. Command Summary Co
Page 73 and 74: DP8340 MODE CODE SI (0F)H FUNCTION
Page 75 and 76: DP8340 MODE CODE FUNCTION ESC N n (
Page 77 and 78: ESC/POS 5 : ESC/POS Mode Command Su
Page 79 and 80: APPENDIX Refer to the industry stan
Page 81 and 82: APPENDIX (2) Interleaved 2 of 5 (IT
Page 83 and 84: APPENDIX (4) UPC (5) JAN/EAN-8 (6)
Page 85 and 86: APPENDIX 3) 2-character set codes C
Page 87 and 88: APPENDIX Appendix 2 : Sensor adjust
Page 89 and 90:
APPENDIX STAR Line Mode (Character
Page 91 and 92:
APPENDIX STAR Line Mode (Character
Page 93 and 94:
APPENDIX STAR Line Mode Code Page #
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
APPENDIX A3-2. STAR Page Mode - 100
Page 105 and 106:
APPENDIX STAR Page Mode (Character
Page 107 and 108:
APPENDIX A3-3. DP8340 Mode (U.S.A.
Page 109 and 110:
APPENDIX DP8340 Mode (IBM Character
Page 111 and 112:
APPENDIX DP8340 Mode (IBM Character
Page 113 and 114:
APPENDIX DP8340 Mode (JAPAN) - 110
Page 115 and 116:
APPENDIX DP8340 Mode International
show all

Programmer's Manual TSP700/800 Series - i-POS.nl BV

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?