Single-Chip Low Power RF Transceiver for Narrowband Systems ...

More documents

Recommendations

Info

27.4. Plastic Tube Specification Description: MAGAZINE, 7X7 QFN CC1021 Tube Specification Device Package Tube Width Tube Length Units per Tube CC1021RUZ QFN 32 8.91 mm 381 mm 52 28. Ordering Information Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead Finish MSL Peak Temp (3) CC1021RUZ Active QFN RUZ 32 2080 Green (RoHS & Cu NiPdAu LEVEL3-260C no Sb/Br) 1 YEAR CC1021RUZR Active QFN RUZ 32 2500 Green (RoHS & Cu NiPdAu LEVEL3-260C no Sb/Br) 1 YEAR Note: The CC1020/1070DK Development Kit with a fully assembled CC1020EMX Evaluation Module should be used for evaluation of the CC1021 transceiver. Orderable Evaluation Module Description Minimum Order Quantity CC1020_1070DK-433 CC1020/1070 Development Kit, 433 MHz 1 CC1020_1070DK-868/915 CC1020/1070 Development Kit, 868/915 MHz SWRS045B Page 88 of 89 1
29. General Information CC1021 Document Revision History Revision Date Description/Changes 1.0 February 2004 First edition 1.1 December 2004 The various sections have been reorganized to improve readability Added chapter numbering Reorganized electrical specification section Electrical specifications updated Changes to sensitivity figures Changes to TX spurious emission and harmonics figures Changes to current consumption figures in RX and TX mode and crystal oscillator, bias and synthesizer mode Changes to noise figure Added figures on modulation bandwidth Updates to section on input / output matching Updates to section on VCO and PLL self-calibration Updates to section on VCO, charge pump and PLL loop filter Updates to section on receiver channel filter bandwidth Updates to section on RSSI Updates to section on image rejection calibration Updates to section on preamble length and sync word Description of OOK modulation and demodulation merged into one section New bill of materials for operation at 433 MHz and 868/915 MHz Added recommended PCB footprint for package (QFN 32) Added information that there should be no via at “pin #1 corner” (section 27.2) Added list of abbreviations Changes to ordering information 1.2 October 2005 RSSI dynamic range changed from 63 dB to 55 dB Recommended CAL_ITERATE changed from 5 to 4 PLL timeout in “Automatic power-up sequencing flow chart” changed from 1024 filter clocks to 127 filter clocks Calibration routine flow chart changed in accordance to CC1021 Errata Note 002 Added chapter on TX data latency 1.3 January 2006 Updates to Ordering Information and Address Information SWRS045A July 2008 Updated Plastic Tube specification, Carrier Tape and Reel specification to reflect new MOQ quantities. SWRS045B February 2009 Package Description changed to reflect CC1021RUZ in compliance with PCN20081216001. Package Marking changed in compliance with PCN20081216001. Package Thermal Properties removed to align with general TI datasheets Plastic Tube Specification: added device CC1021RUZ and changed tube width to reflect CC1021RUZ in compliance with PCN20081216001. Carrier Tape and Reel Specification: added device CC1021RUZR Ordering Information: changed device orderable names to CC1021RUZ and CC1021RUZR in compliance with PCN20081216001. Added important information and disclaimer Product Status Definition: removed Carrier Tape and Reel Specification is removed, since this was duplicate information to Tape And Reel Information SWRS045B Page 89 of 89
Page 1 and 2:
CC1021 CC1021 Single Chip Low Power
Page 3 and 4:
CC1021 13. Transmitter ............
Page 5 and 6:
2. Absolute Maximum Ratings CC1021
Page 7 and 8:
Parameter Spurious emission, radiat
Page 9 and 10:
Input IP3 Parameter 433 MHz 102.4 k
Page 11 and 12:
4.3. RSSI / Carrier Sense Section P
Page 13 and 14:
4.6. Frequency Synthesizer Section
Page 15 and 16:
4.8. Current Consumption Parameter
Page 17 and 18:
6. Circuit Description RF_IN LNA RF
Page 19 and 20:
Microcontroller configuration inter
Page 21 and 22:
8. Configuration Overview CC1021 ca
Page 23 and 24:
9.1. 4-wire Serial Configuration In
Page 25 and 26:
9.2. Signal Interface The CC1021 ca
Page 27 and 28:
Transmitter side: DCLK DIO “RF”
Page 29 and 30:
f ref f xosc = REF _ DIV + 1 FSK fr
Page 31 and 32:
The DEC_DIV[2:0] bits in the FILTER
Page 33 and 34:
12.5. RSSI CC1021 has a built-in RS
Page 35 and 36:
12.6. Image Rejection Calibration F
Page 37 and 38: Blocker rejection [dB] 65 60 55 50
Page 39 and 40: • Frequency register setting is s
Page 41 and 42: 12.11. Carrier Sense The carrier se
Page 43 and 44: offset. The new frequency must be c
Page 45 and 46: Current [mA] / Output power [dBm] C
Page 47 and 48: CC1021 CC1021 RF_OUT RF_IN C60 L1 A
Page 49 and 50: 868 MHz CC1021 Figure 28: Typical o
Page 51 and 52: 15.2. VCO and PLL Self-Calibration
Page 53 and 54: CC1021 Loop C6 C7 C8 R2 R3 PLL turn
Page 55 and 56: Rese tCC102 0 WakeupCC1020ToRx/ Wak
Page 57 and 58: the "carrier sense" level (programm
Page 59 and 60: Item CL= 12 pF CL= 16 pF CL= 22 pF
Page 61 and 62: LNA_EN and PA_EN are used to contro
Page 63 and 64: frequencies is done through the MAI
Page 65 and 66: 26.1. CC1021 Register Overview CC10
Page 67 and 68: CC1021 INTERFACE Register (01h) REG
Page 69 and 70: CC1021 CLOCK_A Register (07h) REGIS
Page 71 and 72: CC1021 MODEM Register (0Dh) REGISTE
Page 73 and 74: CC1021 VGA1 Register (11h) REGISTER
Page 75 and 76: CC1021 VGA3 Register (13h) REGISTER
Page 77 and 78: CC1021 FRONTEND Register (16h) REGI
Page 79 and 80: BUFF_CURRENT Register (19h) REGISTE
Page 81 and 82: CC1021 TEST1 Register (21h, for tes
Page 83 and 84: CC1021 AFC Register (43h, read only
Page 85 and 86: 27. Package Description (QFN 32) CC
Page 87: 27.2. Recommended PCB Footprint for
Page 91: *All dimensions are nominal PACKAGE
show all

Single-Chip Low Power RF Transceiver for Narrowband Systems ...

Create successful ePaper yourself

Delete template?

Save as template?