1747-6.22, Backup Scanner User Manual

More documents

Recommendations

Info

7-136 RIO Block Transfer Publication 1747-6.22 Directional Non-Continuous Block Transfer Example The following rungs demonstrate a directional non-continuous block transfer. The block transfer executes once for every false-to-true transition of the input. Please note that the input bit I:2.0/0 was chosen randomly for this example and can be any address in your program used to initiate a BTR. Also note that this same method may be used for a BTW. Rung 2:0 Configure the BTR operation type, length and rio address at power-up. Bit B3:100/7 must be set prior to going to run to indicate a BTR operation. | | | | | | | POWER±UP BTR | | BIT CONTROL | | S:1 +COP---------------+ | |----] [--------------------------------------------------+COPY FILE +- | 15 |Source #B3:100| | | |Dest #M0:1.100| | | |Length 3| | | +------------------+ | Rung 2:1 Copy the BTR status area to a binary file, which is used throughout the program. This avoids addressing the M1 file multiple times during each program scan. Each time an instruction containing an M1 file bit, word or file is scanned b the processor, an immediate data transfer to the module occurs and therefore will impact the overall processor scan time. | | | | | | | BTR | | PENDING BTR STATUS | | B3 +COP---------------+ | |-+----] [-----+------------------------------------------+COPY FILE +- | | 80 | |Source #M1:1.100| | | | | |Dest #B3:0| | | | | |Length 4| | | | | +------------------+ | | | | | | | | | | | | | | | CHECK BTR | | | | STATUS | | | | B3 | | | +----] [-----+ | | 81 | Rung 2:2 Unlatch the bit that continues to check the BTR status. When a BTR is complete, the done or error bit is set. The ladder program must then unlatch the enable bit, then wait for the SN module to turn off the done/error bit before another BTR to the same M-file location can be initiated. This is one complete BTR cycle. | | | | | VIRTUAL | | BTR DONE CHECK BTR | | BIT STATUS | | B3 B3 | |-+----]/[-----+-------------------------------------------------------(U)-----| | | 13 | 81 | | | | | | | | | | | | | | | | | | | VIRTUAL | | | | BTR ERROR | | | | BIT | | | | B3 | | | +----]/[-----+ | | 12 |
RIO Block Transfer 7-137 Rung 2:3 When BTR successfully completes, buffer the BTR data and unlatch the BTR enable bit. Also, unlatch the BTR pending bit and latch the bit that continues checking the BTR status until the SN turns off the done bit. | | | | | VIRTUAL | | BTR DONE | | BIT BTR DATA | | B3 +COP---------------+ | |----] [------------------------------------------------+COPY FILE +-+-| | 13 | |Source #M1:1.110| | | | | |Dest #N7:10| | | | | |Length 64| | | | | +------------------+ | | | | | | | | | | | | | | | | BTR | | | | PENDING | | | | B3 | | | +----(U)---------------+ | | | 80 | | | | | | | | | | | | VIRTUAL | | | | BTR ENABLE | | | | BIT | | | | B3 | | | +----(U)---------------+ | | | 1615 | | | | | | | | | | | | | | | | CHECK BTR | | | | STATUS | | | | B3 | | | +----(L)---------------+ | | 81 | Rung 2:4 | | | | | VIRTUAL | | BTR ERROR | | BIT | | B3 +MOV---------------+ | |----] [------------------------------------------------+MOVE +-+-| | 12 | |Source M1:1.103| | | | | | *| | | | | |Dest N7:9| | | | | | 0| | | | | +------------------+ | | | | | | | | | | | | | | | | BTR | | | | PENDING | | | | B3 | | | +----(U)---------------+ | | | 80 | | | | | | | | | | | | VIRTUAL | | | | BTR ENABLE | | | | BIT | | | | B3 | | | +----(U)---------------+ | | | 1615 | | | | | | | | | | | | | | | | CHECK BTR | | | | STATUS | | | | B3 | | | +----(L)---------------+ | | 81 | Publication 1747-6.22
Page 1 and 2:
Backup Scanner 1747-BSN User Manual
Page 3 and 4:
Overview Table of Contents Preface
Page 5 and 6:
Scanner Configuration and Programmi
Page 7 and 8:
Switchover Considerations Programmi
Page 9 and 10:
Glossary Index Table of Contents xi
Page 11 and 12:
Who Should Use This Manual How to U
Page 13 and 14:
Conventions Used in This Manual The
Page 15 and 16:
Overview This chapter contains the
Page 17 and 18:
Local I/O Remote I/O Processor I/O
Page 19 and 20:
SLC and Scanner Asynchronous Operat
Page 21 and 22:
RIO Logical Rack 0 RIO Logical Rack
Page 23 and 24:
Physical and Logical RIO Link Speci
Page 25 and 26:
Overview 1-27 Complementary I/O: Pl
Page 27 and 28:
Overview 1-29 Complementary I/O: Pl
Page 29 and 30:
Slot Pair I O I O I O I O 0 1 2 3 4
Page 31 and 32:
Hardware Features Overview 1-33 Not
Page 33 and 34:
Module Address Switch Overview 1-35
Page 35 and 36:
A Typical SLC 500 Backup Configurat
Page 37 and 38:
Overview 1-39 Data table values are
Page 39 and 40:
Required Tools and Equipment Chapte
Page 41 and 42:
5. Configure the system. Quick Star
Page 43 and 44:
Configuration Selection Installatio
Page 45 and 46:
Backup Scanner Installation Install
Page 47 and 48:
Installation and Wiring 3-49 Termin
Page 49 and 50:
Chapter 4 Operating Your SLC 500 Ba
Page 51 and 52:
(1) Operating Your SLC 500 Backup S
Page 53 and 54:
Operating Your SLC 500 Backup Syste
Page 55 and 56:
Startup Sequencing Operating Your S
Page 57 and 58:
Understanding Remote Input and Outp
Page 59 and 60:
Page 61 and 62:
Rules for Configuring the Scanner G
Page 63 and 64:
Logical Rack 0 Logical Rack 1 Logic
Page 65 and 66:
Considerations When Configuring Rem
Page 67 and 68:
Page 69 and 70:
Output Reset Control Device Inhibit
Page 71 and 72:
M0 File - RIO Device Reset Control
Page 73 and 74:
Page 75 and 76:
M1 Status File Description General
Page 77 and 78:
Logical Device Starting Address Sta
Page 79 and 80:
Logical Device Fault Status M1 (Sta
Page 81 and 82:
Page 83 and 84: Primary Logical Device Address, Wor
Page 85 and 86: SLC/Scanner Configuration Scanner C
Page 87 and 88: Chapter 6 Module Control and Status
Page 89 and 90: Module Control and Status Word 6-91
Page 91 and 92: Transferring Data over the High-Spe
Page 93 and 94: Data Transfer Status Word Module Co
Page 95 and 96: Program File 2 0000 0001 0002 Modul
Page 97 and 98: Program File 4 0000 0001 0002 0003
Page 99 and 100: Module Status Counters Module Contr
Page 101 and 102: RIO Block Transfer Theory of Operat
Page 103 and 104: SLC Processor ➀ RIO Block Transfe
Page 105 and 106: RIO Block Transfer General Function
Page 107 and 108: Example 2 # 2 # 4 # 1 # 2 # 3 # 4 #
Page 109 and 110: M0 File BT Control Buffer Layout BT
Page 111 and 112: Error Code Description RIO Block Tr
Page 113 and 114: RIO Block Transfer 7-115 Your SLC c
Page 115 and 116: Control EN TO Status Flag EW ST ER
Page 117 and 118: Control Flag EN TO Status Flag EW S
Page 119 and 120: Bit Number Octal 17 10 7 Bit Number
Page 121 and 122: Block Transfer Read Control Logic E
Page 123 and 124: RIO Block Transfer 7-125 Rung 2:3 W
Page 125 and 126: RIO Block Transfer 7-127 Rung 2:1 C
Page 127 and 128: Directional Continuous Block Transf
Page 131 and 132: Directional Repeating Block Transfe
Page 133: Rung 2:5 Block transfer reads will
Page 137 and 138: Bidirectional Continuous Block Tran
Page 139 and 140: RIO Block Transfer 7-141 When a BTR
Page 141 and 142: RIO Block Transfer 7-143 Rung 2:9 T
Page 143 and 144: RIO Block Transfer 7-145 Rung 2:1 C
Page 147 and 148: RIO Block Transfer 7-149 Rung 2:10
Page 149 and 150: RIO Block Transfer 7-151 Rung 2:2 U
Page 153 and 154: RIO Block Transfer 7-155 Rung 2:11
Page 155 and 156: Switchover Considerations Chapter 8
Page 157 and 158: Switchover Considerations 8-159 Div
Page 159 and 160: Switchover Considerations 8-161 Dur
Page 161 and 162: Switchover Considerations 8-163 The
Page 163 and 164: Programming Techniques Chapter 9 Ch
Page 165 and 166: Program File 3 0000 0001 0002 0003
Page 167 and 168: 0009 0010 0011 0012 Programming Tec
Page 169 and 170: 0017 Programming Techniques 9-171 T
Page 171 and 172: 0005 0006 0007 0008 0009 0010 0011
Page 173 and 174: 0021 0022 0023 0024 0025 0026 0027
Page 175 and 176: Programming Techniques 9-177 Data T
Page 177 and 178: Programming Techniques 9-179 3. For
Page 179 and 180: Programming Techniques 9-181 The ha
Page 181 and 182: Programming Techniques 9-183 Howeve
Page 183 and 184: Backup Scanner Operating Specificat
Page 185 and 186:
Calculating Throughput Specificatio
Page 187 and 188:
Specifications A-189 You need to ca
Page 189 and 190:
Determining T btx All Baud Rates 57
Page 191 and 192:
Specifications A-193 3. Calculate t
Page 193 and 194:
Backup Scanner Output Delay Time (T
Page 195 and 196:
M0-M1 Files and G Files Appendix B
Page 197 and 198:
Monitoring Bit Addresses M0-M1 File
Page 199 and 200:
Access Time M0-M1 Files and G Files
Page 201 and 202:
S:4/8 causes the #M1:4.3 file to up
Page 203 and 204:
M0-M1 Files and G Files B-205 G Fil
Page 205 and 206:
M0-M1 Files and G Files B-207 With
Page 207 and 208:
RIO Configuration Worksheet Appendi
Page 209 and 210:
Glossary The following terms are us
Page 211 and 212:
Glossary 213 Module Status Word (MS
Page 213 and 214:
Numerics 1/2-slot addressing, 1-13,
Page 215 and 216:
minimizing the scan time, B-6 speci
Page 217 and 218:
Index I-ccxix Publication 1747-6.22
Page 219:
Publication 1747-6.22 — October 1
show all

1747-6.22, Backup Scanner User Manual

Create successful ePaper yourself

Delete template?

Save as template?