Generation C / Génération C - ASCO Numatics

More documents

Recommendations

Info

■ Setting of the transmission speed The transmission speed does not need to be adjusted, it is fi xed at 1 MBaud. RESET POSITION FIPIO islands are provided with a reset into zero position (confi guration bridge on two pins) FUSES See page 19 (same as Profi bus-DP) + 5 V + 24 V RUN I/O COM ERR VALVE ISLANDS - GENERATION C ■ Diagnostics LED INDICATIONS - ON THE BUSLINK MODULE The buslink module is provided with 6 diagnostic LEDs to FIPIO standard. RUN / green: All components connected to power supply - No display if not connected to power supply - Flashing light if bus communication is interrupted because another component accesses the same address (frequency = approx. 2Hz). COM / yellow : Communication is activated. - No display when there is no data exchange over the FIPIO bus or when communication is interrupted. - Flashing light during autotest, initialisation and connection of new components (Frequency = approx. 2 Hz). - Flashing light when the components participate in the data exchange over the FIPIO bus; fl ashing is at a fi xed frequency of approx. 2 MHz. ERR / red: Major error - No display during regular operation. - Flashing light during autotest, initialisation and connection of new components and as long as the components are not logically connected to the FIPIO network (frequency = approx. 2 Hz). - Lights up in case of error requiring an exchange of component or module (fault in a subassembly, assembly of incompatible modules etc.) I/O / red : Minor error - No display during regular operation. - Flashing light during autotest, initialisation and connection of new components (frequency = approx. 2Hz). - Lights fup in case of error not caused by one of the components. As soon as the components are powered-on, these 4 LEDS fl ash simultaneously during the components' autotest phase. If the LEDS continue to fl ash after the autotest, this means that the address which was confi gured is already occupied. + 24V (green) lights up as soon as the power supply for the spool valves/outputs is connected. +5V (green) lights up as soon as the power supply to the bus electronics/inputs is connected. ERRORS Errors in series 7 are displayed in the word STATUS A and in the APRIL 5000 under "external Error". STATUS A External error Signifi cation Bit 3 Bit 1 Problem with 24V power supply to the outputs Bit 1 Bit 3 Problem with power supply to the bus interface Bit 0 Bit 4 Problem of overload at the outputs If such an error occurs, the red I/O LED lights up (see above) - ON THE BUS CONTROLLER OF THE PLC The front panel of the controller is equipped with several displays which allow to locate errors in the FIPIO system and sensors/actuators. For detailed information see the FIPIO controller manual. DIAGNOSTICS REGISTER The diagnostics register gives the error status of the FIPIO system in bit information. An appropriate software evaluation and/or error reaction is possible by bit comparison. All leafl ets are available on: www.asconumatics.eu 26 Bridge to confi gure the reset position To obtain a self-locking reset position remove the bridge and put it on one pin only so as not to lose it. 00236GB-2005/R01 Availability, design and specifi cations are subject to change without notice. All rights reserved.
00236GB-2005/R01 Availability, design and specifi cations are subject to change without notice. All rights reserved. MODBUS ■ Connection of M12 connectors (Ref. G, page 15) 4 1 5 3 2 View from screw side of connector ■ Programming instructions VALVE ISLANDS - GENERATION C Pin Signal name Description 1 Tx + RS 485 high 2 5V - Bus 5V power supply to terminating resistor 3 Tx - RS 485 low 4 GND - BUS ( ) * GND - signal 5 NC - Shield - Protection earth ( * ) In case of connection with 2-wire cable, pin 4 must be connected. According to the PLC network cards, please fi nd below all specifi cations to parameter a JOUCOMATIC island with Modbus. - Speed : 4800, 9600 or 19200 Baud - Island profi le: "RTU - 8 bit format with parity" Make sure that the parity you choose corresponds to that defi ned for the CPU. - Connection type: RS 485 - 2 wires ■ Address selection + 5 V + 24 V RUN/MOD ERR/NET ON ON 8 1 4 1 NOTE: The default address of the module is "03" at delivery You can change the island's address with the dip switches in the bus coupling module. Example of an island with address # 03 8 7 6 5 4 3 2 1 OFF ON Position 8 7 6 5 4 3 2 1 Signifi cative value 1 2 4 8 16 32 64 128 Address 00 ADR 02 ADR 03 ADR 04 I I ADR 254 ADR 255 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 All leafl ets are available on: www.asconumatics.eu 27
Page 1 and 2: PNEUMATIC SPOOL VALVE ISLANDS MULTI
Page 3 and 4: 00454GB-2007/R01 Availability, desi
Page 27: 00236GB-2005/R01 Availability, desi
Page 33: VALVE ISLANDS - GENERATION C All le

Generation C / Génération C - ASCO Numatics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?