7.8.1.0 - Force10 Networks

More documents

Recommendations

Info

Enable graceful restart Graceful Restart is enabled for the global OSPF process. Use these commands to configure OSPF graceful restart. Refer to Graceful Restart on page 524 for feature details. The Force10 Networks implementation of OSPF graceful restart enables you to specify: • grace period—the length of time the graceful restart process can last before OSPF terminates it. • helper-reject neighbors—the router ID of each restart router that does not receive assistance from the configured router. • mode—the situation or situations that trigger a graceful restart. • role—the role or roles the configured router can perform. Note: By default, OSPF graceful restart is disabled. You enable OSPF graceful restart in CONFIGURATION ROUTER OSPF mode. Command Syntax Command Mode Usage graceful-restart grace-period seconds graceful-restart helper-reject router-id graceful-restart mode [planned-only | unplanned-only] CONFIG-ROUTER- OSPF-id Enable OSPF graceful-restart globally and set the grace period. Seconds range: between 40 and 3000 This is the period of time that an OSPF router’s neighbors will advertise it as fully adjacent, regardless of the synchronization state, during a graceful restart. OSPF terminates this process when the grace period ends. CONFIG-ROUTER- OSPF-id CONFIG-ROUTER- OSPF-id Enter the Router ID of the OSPF helper router from which the router does not accept graceful restart assistance. This applies to the specified router only. IP Address: A.B.C.D Specify the operating mode in which graceful-restart functions. FTOS supports the following options: • Planned-only. The OSPF router supports graceful-restart for planned restarts only. A planned restart is when the user manually enters a fail-over command to force the primary RPM over to the secondary RPM. During a planned restart, OSPF sends out a Grace LSA before the system switches over to the secondary RPM. OSPF also is notified that a planned restart is happening. • Unplanned-only. The OSPF router supports graceful-restart for only unplanned restarts. During an unplanned restart, OSPF sends out a Grace LSA once the secondary RPM comes online. By default, OSPF supports both planned and unplanned restarts. Selecting one or the other mode restricts OSPF to the single selected mode. 540 Open Shortest Path First (OSPFv2 and OSPFv3)
Command Syntax Command Mode Usage graceful-restart role [helper-only | restart-only] When you configure a graceful restart, the show run ospf command (Figure 351) displays information similar to the following. Figure 351 Command Example: show run ospf (partial) Force10#show run ospf ! router ospf 1 graceful-restart grace-period 300 graceful-restart role helper-only graceful-restart mode unplanned-only graceful-restart helper-reject 10.1.1.1 graceful-restart helper-reject 20.1.1.1 network 10.0.2.0/24 area 0 Force10# Use the following command to disable OSPF graceful-restart after you have enabled it. For more information on OSPF graceful restart, refer to the FTOS Command Line Interface Reference. Configure virtual links CONFIG-ROUTER- OSPF-id Areas within OSPF must be connected to the backbone area (Area ID 0.0.0.0). If an OSPF area does not have a direct connection to the backbone, at least one virtual link is required. Virtual links must be configured on an ABR connected to the backbone. • hello-interval: help packet • retransmit-interval: LSA retransmit interval • transmit-delay: LSA transmission delay • dead-interval: dead router detection time • authentication-key: authentication key • message-digest-key: MD5 authentication key Configure the graceful restart role or roles that this OSPF router performs. FTOS supports the following options: • Helper-only. The OSPF router supports graceful-restart only as a helper router. • Restart-only. The OSPF router supports graceful-restart only during unplanned restarts. By default, OSPF supports both restarting and helper roles. Selecting one or the other role restricts OSPF to the single selected role. Command Syntax Command Mode Usage no graceful-restart grace-period CONFIG-ROUTER- OSPF-id Disable OSPF graceful-restart. Returns OSPF graceful-restart to its default state. FTOS Configuration Guide, version 7.8.1.0 541
Page 1 and 2:
FTOS Configuration Guide for ® the
Page 3 and 4:
This chapter contains the following
Page 5 and 6:
Enhanced Fan Tray: The enhanced fan
Page 7 and 8:
• Management on page 8 • System
Page 9 and 10:
System • SNMP OID for Interface O
Page 11 and 12:
Contents New Features . . . . . . .
Page 13 and 14:
Chapter 4 802.1X . . . . . . . . .
Page 15 and 16:
Multi-Exit Discriminators (MEDs) .
Page 17 and 18:
Chapter 13 Internet Group Managemen
Page 19 and 20:
UDP Helper with Broadcast-all Addre
Page 21 and 22:
Viewing Information Advertised by A
Page 23 and 24:
Override Bootstrap Router Updates .
Page 25 and 26:
Chapter 32 Remote Monitoring . . .
Page 27 and 28:
Chapter 37 Storm Control. . . . . .
Page 29 and 30:
Appendix A Standards Compliance . .
Page 31 and 32:
Preface About this Guide Objectives
Page 33 and 34:
The FTOS Command Line Interface (CL
Page 35 and 36:
Figure 2 CLI Modes in FTOS EXEC EXE
Page 37 and 38:
Table 2 FTOS Command Modes CLI Comm
Page 39 and 40:
Obtaining Help Obtain a list of key
Page 41 and 42:
Filtering show Command Outputs Filt
Page 43 and 44:
Chapter 2 Getting Started This chap
Page 45 and 46:
Configuring a Host Name The host na
Page 47 and 48:
To configure a username and passwor
Page 49 and 50:
Copying Files to and from the Syste
Page 51 and 52:
Task Command Syntax Command Mode Sa
Page 53 and 54:
Viewing Configuration Files Configu
Page 55 and 56:
Chapter 3 Management Management is
Page 57 and 58:
Task Command Syntax Command Mode Al
Page 59 and 60:
Apply a Privilege Level to a Userna
Page 61 and 62:
Send System Messages to a Syslog Se
Page 63 and 64:
Display the Logging Buffer and the
Page 65 and 66:
Synchronize log messages You can co
Page 67 and 68:
Enable FTP server To enable the sys
Page 69 and 70:
• Enable diagnostics on an SFM on
Page 71 and 72:
To view diagnostic results, use the
Page 73 and 74:
Step Task Command Syntax Command Mo
Page 75 and 76:
A two types of locks can be set: au
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Chapter 4 802.1X 802.1X is supporte
Page 83 and 84:
Figure 38 RADIUS Frame Format Code
Page 85 and 86:
Configuring 802.1X Configuring 802.
Page 87 and 88:
Configuring Request Identity Re-tra
Page 89 and 90:
• ForceUnauthorized an unauthoriz
Page 91 and 92:
Figure 45 Configuring a Reauthentic
Page 93 and 94:
In Figure 47 shows the configuratio
Page 95 and 96:
Figure 49 Configuring an Authentica
Page 97 and 98:
Chapter 5 IP Access Control Lists (
Page 99 and 100:
• L3 ACL (ipv4acl): 6 • L2 ACL(
Page 101 and 102:
In cases such as these, where class
Page 103 and 104:
Figure 54 illustrates how the seq c
Page 105 and 106:
To create a filter for TCP packets
Page 107 and 108:
Established Flag The est (establish
Page 109 and 110:
To view which IP ACL is applied to
Page 111 and 112:
• To deny routes with a mask less
Page 113 and 114:
Step Command Syntax Command Mode Pu
Page 115 and 116:
Command Syntax Command Mode Purpose
Page 117 and 118:
Create a route map Route maps, ACLs
Page 119 and 120:
Example 1 Force10(conf)#route-map f
Page 121 and 122:
To configure a set condition, use a
Page 123 and 124:
Note: If the continue clause is con
Page 125 and 126:
Chapter 6 Border Gateway Protocol B
Page 127 and 128:
A stub AS is one that is connected
Page 129 and 130:
Establishing a session Information
Page 131 and 132:
BGP Attributes Routes learned via B
Page 133 and 134:
• A path with no AS_PATH configur
Page 135 and 136:
An MED is a non-transitive attribut
Page 137 and 138:
Next Hop The Next Hop is the IP add
Page 139 and 140:
Figure 82 shows a scenario where Ro
Page 141 and 142:
• SNMP set for BGP is not support
Page 143 and 144:
Table 7 displays the default values
Page 145 and 146:
Page 147 and 148:
The third line of the show ip bgp n
Page 149 and 150:
Page 151 and 152:
Use the show ip bgp peer-group comm
Page 153 and 154:
Use the show ip bgp neighbors comma
Page 155 and 156:
Page 157 and 158:
To disable this feature, use the no
Page 159 and 160:
Page 161 and 162:
Filtering with Regular ExpressionFi
Page 163 and 164:
Use these commands in the following
Page 165 and 166:
Manipulate the COMMUNITY attribute
Page 167 and 168:
Use the show ip bgp community comma
Page 169 and 170:
Use the following command in the CO
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Use the following commands in the C
Page 177 and 178:
To set dampening parameters via a r
Page 179 and 180:
Change BGP timers Use either or bot
Page 181 and 182:
Route map continue The BGP route ma
Page 183 and 184:
Debugging BGP Use any of the comman
Page 185 and 186:
Capturing PDUs Capture incoming and
Page 187 and 188:
Figure 105 is a graphic illustratio
Page 189 and 190:
Figure 107 Enable BGP - Router 2 R2
Page 191 and 192:
Figure 109 Enable Peer Group - Rout
Page 193 and 194:
Figure 111 Enable Peer Groups - Rou
Page 195 and 196:
Page 197 and 198:
Chapter 7 Border Gateway Protocol B
Page 199 and 200:
A stub AS is one that is connected
Page 201 and 202:
Establishing a session Information
Page 203 and 204:
BGP Attributes Routes learned via B
Page 205 and 206:
• A path with no AS_PATH configur
Page 207 and 208:
An MED is a non-transitive attribut
Page 209 and 210:
Next Hop The Next Hop is the IP add
Page 211 and 212:
Figure 122 shows a scenario where R
Page 213 and 214:
• SNMP set for BGP is not support
Page 215 and 216:
Table 10 displays the default value
Page 217 and 218:
Page 219 and 220:
The third line of the show ip bgp n
Page 221 and 222:
Page 223 and 224:
Use the show ip bgp peer-group comm
Page 225 and 226:
Use the show ip bgp neighbors comma
Page 227 and 228:
Page 229 and 230:
To disable this feature, use the no
Page 231 and 232:
Page 233 and 234:
Filtering with Regular ExpressionFi
Page 235 and 236:
Use these commands in the following
Page 237 and 238:
Manipulate the COMMUNITY attribute
Page 239 and 240:
Use the show ip bgp community comma
Page 241 and 242:
Use the following command in the CO
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Use the following commands in the C
Page 249 and 250:
To set dampening parameters via a r
Page 251 and 252:
Change BGP timers Use either or bot
Page 253 and 254:
Route map continue The BGP route ma
Page 255 and 256:
Debugging BGP Use any of the comman
Page 257 and 258:
Capturing PDUs Capture incoming and
Page 259 and 260:
Figure 145 is a graphic illustratio
Page 261 and 262:
Figure 147 Enable BGP - Router 2 R2
Page 263 and 264:
Figure 149 Enable Peer Group - Rout
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Chapter 8 Configuration Replace and
Page 271 and 272:
You do not have to enable the archi
Page 273 and 274:
Figure 158 Force10#configure replac
Page 275 and 276:
Configuring Auto-archive Figure 162
Page 277 and 278:
Figure 164 Viewing the Difference b
Page 279 and 280:
Chapter 9 Dynamic Host Configuratio
Page 281 and 282:
• Option 82 on page 281 • DHCP
Page 283 and 284:
Enable DCHP snooping Step Task Comm
Page 285 and 286:
Chapter 10 Force10 Service Agent Fo
Page 287 and 288:
Designating an administrator email
Page 289 and 290:
Each command in the procedure, abov
Page 291 and 292:
Using FTSA for Event Handling The p
Page 293 and 294:
4 5 6 contact-name name CONFIGURATI
Page 295 and 296:
Table 13 shows the three preset tes
Page 297 and 298:
The following tests are all configu
Page 299 and 300:
Using the basic procedure presented
Page 301 and 302:
• Message type 2: On system failo
Page 303 and 304:
Figure 173 shows an example of the
Page 305 and 306:
Using FTSA Show Commands The FTSA
Page 307 and 308:
Chapter 11 GARP VLAN Registration P
Page 309 and 310:
Enabling GVRP Globally Enable GVRP
Page 311 and 312:
Chapter 12 High Availability High A
Page 313 and 314:
Message 5 FTOS Version Incompatibil
Page 315 and 316:
C-Series RPMs have one CPU, the CP.
Page 317 and 318:
RPM synchronization Data between th
Page 319 and 320:
On the C-Series, when a secondary R
Page 321 and 322:
Pre-configuring a line card slot Yo
Page 323 and 324:
Graceful Restart Graceful Restart i
Page 325 and 326:
• Hot-lock IP ACLs (supported on
Page 327 and 328:
If you do not have the proper boot
Page 329 and 330:
View your cache boot configuration
Page 331 and 332:
Chapter 13 IGMP version 1, version
Page 333 and 334:
Figure 196 Leaving a Multicast Grou
Page 335 and 336:
Figure 198 2 Interface Multicast Gr
Page 337 and 338:
Viewing IGMP Enabled Interfaces Int
Page 339 and 340:
Adjusting the IGMP Querier Timeout
Page 341 and 342:
Enabling IGMP Immediate-leave Confi
Page 343 and 344:
Chapter 14 Interfaces This chapter
Page 345 and 346:
Overview of Layer Modes On all syst
Page 347 and 348:
Configuration Task List for Physica
Page 349 and 350:
Configuring Layer 3 mode By assigni
Page 351 and 352:
To configure IP addresses on a Mana
Page 353 and 354:
To assign an IP address, use the fo
Page 355 and 356:
With this feature, the user can cre
Page 357 and 358:
The port channel is now enabled and
Page 359 and 360:
Figure 216 Error Message Force10(co
Page 361 and 362:
Configure the minimum oper up links
Page 363 and 364:
Balancing may be applied to IPv4, s
Page 365 and 366:
Hash algorithm The load-balance com
Page 367 and 368:
Create a single-range Figure 219 Cr
Page 369 and 370:
To show the defined interface-range
Page 371 and 372:
Figure 226 Command Example: monitor
Page 373 and 374:
• This feature is not supported o
Page 375 and 376:
• Link dampening can be applied t
Page 377 and 378:
The globally assigned 48-bit Multic
Page 379 and 380:
Configuring MTU Size on an Interfac
Page 381 and 382:
Setting speed and duplex mode of Et
Page 383 and 384:
Figure 235 Setting Auto-Negotiation
Page 385 and 386:
Figure 238 Configuring Rate Interva
Page 387 and 388:
Clearing interface counters The cou
Page 389 and 390:
Chapter 15 IP Addressing IP Address
Page 391 and 392:
To assign an IP address to an inter
Page 393 and 394:
To view the configured routes, use
Page 395 and 396:
Enable dynamic resolution of host n
Page 397 and 398:
ARP FTOS uses two forms of address
Page 399 and 400:
Page 401 and 402:
2. Configure a broadcast address on
Page 403 and 404:
UDP Helper with Broadcast-all Addre
Page 405 and 406:
Packet 2 is sent from a host on VLA
Page 407 and 408:
Chapter 16 IPv6 Introduction This c
Page 409 and 410:
• Prefix Renumbering - Useful in
Page 411 and 412:
The Payload Length limit of 2 bytes
Page 413 and 414:
01 Discard the packet. 10 Discard t
Page 415 and 416:
Implementing IPv6 with FTOS FTOS su
Page 417 and 418:
Feature and/or Functionality First
Page 419 and 420:
Figure 257 MTU Discovery Path Sourc
Page 421 and 422:
• PIM in Source Specific Multicas
Page 423 and 424:
Figure 260 Command Example: show ca
Page 425 and 426:
Assign a Static IPv6 Route IPv6 Sta
Page 427 and 428:
Page 429 and 430:
Figure 262 illustrates the show ipv
Page 431 and 432:
Clear IPv6 Routes Use the clear IPv
Page 433 and 434:
Chapter 17 Link Aggregation Control
Page 435 and 436:
FTOS supports LAGs in the following
Page 437 and 438:
Set the LACP long timeout PDUs are
Page 439 and 440:
Step Task Command Command Mode 2 Cr
Page 441 and 442:
Configure LACP to be hitless using
Page 443 and 444:
Figure 279 Inspecting Configuration
Page 445 and 446:
Summary of the configuration on ALP
Page 447 and 448:
Figure 283 Using the show interface
Page 449 and 450:
Figure 285 Using the show lacp Comm
Page 451 and 452:
Chapter 18 Layer 2 Layer 2 features
Page 453 and 454:
This section has the following sub-
Page 455 and 456:
Task Command Syntax Command Mode Sh
Page 457 and 458:
Figure 288 Far-end Failure Detectio
Page 459 and 460:
Configuring FEFD You can configure
Page 461 and 462:
Figure 293 Debug FEFD packets displ
Page 463 and 464:
Chapter 19 Link Layer Discovery Pro
Page 465 and 466:
Figure 296 Organizationally Specifi
Page 467 and 468:
• storing the information that en
Page 469 and 470:
Figure 298 TLV Type (127) The appli
Page 471 and 472:
Important Points to Remember • LL
Page 473 and 474:
Step Task Command Command Mode * No
Page 475 and 476:
Figure 305 Viewing All Information
Page 477 and 478:
Configuring Transmit and Recieve Mo
Page 479 and 480:
Figure 309 debug lldp detail—LLDP
Page 481 and 482:
Table 43 LLDP System MIB Objects TL
Page 483 and 484:
Chapter 20 Multiple Spanning Tree P
Page 485 and 486:
4. Create Multiple Spanning Tree In
Page 487 and 488:
Figure 313 Viewing MSTP Port States
Page 489 and 490: Figure 315 Viewing the MSTP Region
Page 491 and 492: Task Command Syntax Command Mode Ch
Page 493 and 494: Figure 319 Router 1 Running-configu
Page 495 and 496: Figure 321 Router 3 Running-configu
Page 497 and 498: Figure 323 Displaying BPDUs and Eve
Page 499 and 500: Chapter 21 Multicast Features This
Page 501 and 502: Limit the Number of Multicast Route
Page 503 and 504: Rate Limit IGMP Join Requests If yo
Page 505 and 506: Prevent a PIM Router from Processin
Page 507 and 508: Tune the Central Scheduler for Mult
Page 509 and 510: Chapter 22 Network Time Protocol Ne
Page 511 and 512: Configure NTP broadcasts With FTOS,
Page 513 and 514: Configure a source IP address for N
Page 515 and 516: _ls Chapter 23 Open Shortest Path F
Page 517 and 518: Areas allow you to further organize
Page 519 and 520: Figure 336gives some examples of th
Page 521 and 522: Link-State Advertisements (LSAs) A
Page 523 and 524: Cost is a numbered rating 1-65535.
Page 525 and 526: Multi-Process OSPF (OSPFv2, IPv4 on
Page 527 and 528: OSPF Adjacency with Cisco Routers T
Page 529 and 530: Use these commands on one of the in
Page 531 and 532: Message 15 If you try to enable mor
Page 533 and 534: OSPF, by default, sends hello packe
Page 535 and 536: Use the following command in the RO
Page 537 and 538: Command Syntax Command Mode Usage N
Page 539: Use the show config command in CONF
Page 543 and 544: Filter routes To filter routes, use
Page 545 and 546: Troubleshooting OSPFv2 FTOS has sev
Page 547 and 548: Use the following command in EXEC P
Page 549 and 550: Enable IPv6 Unicast Routing Command
Page 551 and 552: Configure Passive-Interface Use the
Page 553 and 554: Troubleshooting OSPFv3 FTOS has sev
Page 555 and 556: Basic OSPFv2 Router Topology The fo
Page 557 and 558: Chapter 24 PIM Sparse Mode PIM Spar
Page 559 and 560: the RP to remove the outgoing inter
Page 561 and 562: Figure 358 Viewing the PIM Multicas
Page 563 and 564: Figure 359 Configure S, G Expiry ti
Page 565 and 566: Figure 361 Electing a Rendezvous Po
Page 567 and 568: If a graceful-restart capable route
Page 569 and 570: Chapter 25 PIM Source Specific Mode
Page 571 and 572: Implementation Information • The
Page 573 and 574: Figure 366 R2(conf )#do show ip pim
Page 575 and 576: Chapter 26 Power over Ethernet Powe
Page 577 and 578: Enabling PoE on a Port PoE is disab
Page 579 and 580: Table 51 describes the fields that
Page 581 and 582: Manage Power Priorities PoE-enabled
Page 583 and 584: When a failed PSU is replaced and t
Page 585 and 586: Figure 376 LLDP Configuration for O
Page 587 and 588: Step Task Command Command Mode 1 Cr
Page 589 and 590: Chapter 27 Port Monitoring Port Mon
Page 591 and 592:
Port Monitoring on C-Series and S-S
Page 593 and 594:
Figure 385 Port Monitoring Configur
Page 595 and 596:
Flow-based Monitoring Flow-based Mo
Page 597 and 598:
Chapter 28 Private VLANs FTOS 7.8.1
Page 599 and 600:
Private VLAN Commands The commands
Page 601 and 602:
Creating a Primary VLAN A primary V
Page 603 and 604:
Figure 390 Configuring VLANs for a
Page 605 and 606:
• show vlan private-vlan mapping:
Page 607 and 608:
Chapter 29 Per-VLAN Spanning Tree P
Page 609 and 610:
Page 611 and 612:
To configure hello-time, use the co
Page 613 and 614:
The following command configures th
Page 615 and 616:
To disable PVST+ priority on a part
Page 617 and 618:
Per-Port BPDU Block As detailed in
Page 619 and 620:
Chapter 30 Quality of Service Quali
Page 621 and 622:
Table 57 FTOS Support for Port-base
Page 623 and 624:
Figure 415 Configuring dot1p Priori
Page 625 and 626:
Display how your rate limiting conf
Page 627 and 628:
Figure 423 Using the Order Keyword
Page 629 and 630:
FTOS Behavior: An explicit “deny
Page 631 and 632:
Set a DSCP value for egress packets
Page 633 and 634:
Specify WRED drop precedence Specif
Page 635 and 636:
• You cannot apply an input Layer
Page 637 and 638:
Create WRED Profiles To create a WR
Page 639 and 640:
Allocating Bandwidth to Multicast Q
Page 641 and 642:
Chapter 31 Routing Information Prot
Page 643 and 644:
• Generate a default route on pag
Page 645 and 646:
Control RIP routing updates By defa
Page 647 and 648:
Figure 432 shows an example of the
Page 649 and 650:
Summarize routes Routes in the RIPv
Page 651 and 652:
Configuring RIPv2 on Core 2 Figure
Page 653 and 654:
RIP Configuration on Core 3 Figure
Page 655 and 656:
RIP Configuration Summary Figure 44
Page 657 and 658:
Chapter 32 Remote Monitoring Remote
Page 659 and 660:
Set rmon alarm To set an alarm on a
Page 661 and 662:
The following example shows the rmo
Page 663 and 664:
Chapter 33 Rapid Spanning Tree Prot
Page 665 and 666:
Verify that an interface is in Laye
Page 667 and 668:
View the interfaces participating i
Page 669 and 670:
R1#show spanning-tree rstp Root Ide
Page 671 and 672:
• Max-age is the length of time t
Page 673 and 674:
Verify that EdgePort is enabled on
Page 675 and 676:
Chapter 34 Security Security featur
Page 677 and 678:
Configure Accounting of EXEC and pr
Page 679 and 680:
Configure AAA Authentication login
Page 681 and 682:
Server-side configuration TACACS+:
Page 683 and 684:
Configure the enable password comma
Page 685 and 686:
Figure 460 Configuring a Custom Pri
Page 687 and 688:
RADIUS Authentication and Authoriza
Page 689 and 690:
Page 691 and 692:
To view the configuration of RADIUS
Page 693 and 694:
Figure 462 Failed Authentication Fo
Page 695 and 696:
To view the TACACS+ configuration,
Page 697 and 698:
Figure 464 Specifying an SSH versio
Page 699 and 700:
Figure 466 Enabling SSH Password Au
Page 701 and 702:
Page 703 and 704:
VTY Line and Access-Class Configura
Page 705 and 706:
To apply a MAC ACL on a VTY line, u
Page 707 and 708:
Chapter 35 sFlow Configuring sFlow
Page 709 and 710:
Enable and Disable sFlow By default
Page 711 and 712:
Show sFlow on a Line Card Use the f
Page 713 and 714:
For example, if Gig 1/0 and 1/1 are
Page 715 and 716:
Important Points to Remember • Th
Page 717 and 718:
Chapter 36 Simple Network Managemen
Page 719 and 720:
View your SNMP configuration, using
Page 721 and 722:
To configure system contact and loc
Page 723 and 724:
Table 70 Force10 Enterprise-specifi
Page 725 and 726:
The relevant MIBs for these functio
Page 727 and 728:
Note: In Unix, enter the command sn
Page 729 and 730:
Force10 provides additional MIB Obj
Page 731 and 732:
Assign a VLAN Alias Write a charact
Page 733 and 734:
Figure 498 shows the output for an
Page 735 and 736:
Chapter 37 Storm Control Storm Cont
Page 737 and 738:
Chapter 38 Spanning Tree Protocol S
Page 739 and 740:
Configuring Interfaces for Layer 2
Page 741 and 742:
Verify that Spanning Tree is enable
Page 743 and 744:
Adding an Interface to the Spanning
Page 745 and 746:
The default values are listed in Ta
Page 747 and 748:
FTOS Behavior: BPDU Guard and BPDU
Page 749 and 750:
Chapter 39 Upgrade Procedures Findi
Page 751 and 752:
Chapter 40 VLAN Stacking The Stacka
Page 753 and 754:
Single-Tag and Untagged Support on
Page 755 and 756:
Configuring a VLAN-Stack access por
Page 757 and 758:
Setting the protocol type for VLAN-
Page 759 and 760:
Figure 517 VLAN-Stack Network Examp
Page 761 and 762:
E1200-2 Configuration E1200-2 Confi
Page 763 and 764:
Making a hybrid port a trunk port a
Page 765 and 766:
Customer Port A Configuring VLAN-St
Page 767 and 768:
Port 13/47 is noted as a trunk port
Page 769 and 770:
Chapter 41 Virtual Router Redundanc
Page 771 and 772:
VRRP Benefits With VRRP configured
Page 773 and 774:
To enable a Virtual Router, use the
Page 775 and 776:
Configure a Virtual IP address with
Page 777 and 778:
Configure the VRRP Group’s priori
Page 779 and 780:
Since preempt is enabled by default
Page 781 and 782:
The sum of all the costs for all tr
Page 783 and 784:
Figure 544 Configure VRRP Router 2
Page 785 and 786:
Chapter 42 C-Series Debugging and D
Page 787 and 788:
Table 78 FTOS Link Monitoring Syslo
Page 789 and 790:
Table 81 Poll Manager Syslog Messag
Page 791 and 792:
— CP trace log file (look for a f
Page 793 and 794:
1. Use the show environment command
Page 795 and 796:
When the trace messages are being s
Page 797 and 798:
debug Commands The debug command tr
Page 799 and 800:
Monitoring CPU and Memory Usage via
Page 801 and 802:
Table 89 SNMP Traps and OIDs OID St
Page 803 and 804:
• The complete diagnostics test s
Page 805 and 806:
Figure 560 Viewing Offline Diagnost
Page 807 and 808:
Bringing the Line Card Online Bring
Page 809 and 810:
Deciding Whether to Tune Buffers Fo
Page 811 and 812:
Figure 564 Displaying Buffer Profil
Page 813 and 814:
Sample Configurations The two gener
Page 815 and 816:
Appendix A Standards Compliance Thi
Page 817 and 818:
1027 Using ARP to Implement Transpa
Page 819 and 820:
OSPF FTOS support, per platform RFC
Page 821 and 822:
2571 An Architecture for Describing
Page 823 and 824:
MIB Location Force10 MIBs are under
Page 825 and 826:
Numerics 10/100/1000 Base-T Etherne
Page 827 and 828:
display parameter 42 distribution a
Page 829 and 830:
changing value for a router 168, 24
Page 831 and 832:
configuration requirements 686 conf
Page 833 and 834:
IP address of VLAN-Stack VLAN 765 V
show all

7.8.1.0 - Force10 Networks

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?