GPTLR SERIES (2008 Release) - Maxon

More documents

Recommendations

Info

STEP 6 - CONNECT POWER CABLE TO BATTERY NOTE: MAXON recommends using dielectric grease on all electrical connections. Remove nut from positive (+) battery terminal connector. Connect power cable to the positive (+) battery terminal connector (FIG. 24-1). Reinstall and tighten nut. NUT POSITIVE (+) BATTERY TERMINAL CONNECTING POWER CABLE FIG. 24-1 FUSED POWER CABLE BOLT 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 24
STEP 7 - REMOVE LOCKING BRACKETS 1. Push the control switch to RAISE position to moderately pressurize hydraulic system. Remove tack weld from installation bracket (FIG. 25-1B). Next, unbolt installation bracket (FIG. 25-1B) from RH side of extension plate (FIG. 25- 1A). Repeat for LH side. WARNING ! To prevent possible injury, never work in the area under the platform. Get access to the locking angle from the back of the Liftgate. NOTE: To operate Liftgate, locking bracket must be removed. 2. Remove clamps from forklift and Liftgate. If wood supports were used between forklift and ICC bumper, remove the supports. Back out forklift (FIG. 25-2). FIG. 25-1A FLAT WASHER INSTALLATION BRACKET NUT FIG. 25-1B TOP OF EXTENSION PLATE TACK WELD 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 25 FIG. 25-2
Page 1 and 2: M-04-06 REV. D APRIL 2008 INSTALLAT
Page 3 and 4: SYSTEM DIAGRAMS ...................
Page 5 and 6: GPTLR LIFTGATE COMPONENTS CAUTION !
Page 7 and 8: VEHICLE REQUIREMENTS NOTE: BODY max
Page 9 and 10: VEHICLE REQUIREMENTS - Continued 96
Page 11 and 12: VEHICLE REQUIREMENTS - Continued RE
Page 13 and 14: STEP 1 - WELD LIFTGATE TO VEHICLE -
Page 15 and 16: STEP 1 - WELD LIFTGATE TO VEHICLE -
Page 17 and 18: STEP 2 - RUN POWER CABLE Never rout
Page 19 and 20: STEP 3 - CONNECT POWER CABLE - Cont
Page 21 and 22: STEP 4 - INSTALL CONTROL SWITCH - C
Page 23: STEP 5 - CHECKING HYDRAULIC FLUID -
Page 27 and 28: STEP 7 - REMOVE LOCKING BRACKETS -
Page 29 and 30: STEP 8 - FINISH WELDING EXTENSION P
Page 31 and 32: STEP 9 - ADJUST PLATFORM (IF REQUIR
Page 39 and 40: STEP 10 - FINISH WELDING LIFTGATE T
Page 41 and 42: STEP 12 - ADJUST OPENER (IF REQUIRE
Page 43 and 44: STEP 12 - ADJUST OPENER (IF REQUIRE
Page 45 and 46: STEP 14 - ADJUST UNDERRIDE (IF REQU
Page 51 and 52: STEP 15 - ATTACH DECALS - Continued
Page 53 and 54: STEP 17 - VEHICLE TAILLIGHT POSITIO
Page 55 and 56: STEP 17 - VEHICLE TAILLIGHT POSITIO
Page 57 and 58: SYSTEM DIAGRAMS PUMP & MOTOR SOLENO
Page 59 and 60: HYDRAULIC SCHEMATIC (GRAVITY DOWN)
Page 61 and 62: ELECTRICAL SCHEMATIC (GRAVITY DOWN)
Page 63 and 64: OPTIONS RECOMMENDED LIFTGATE POWER

GPTLR SERIES (2008 Release) - Maxon

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?