Responder LE Model 5701 Security and Remote Start Installation ...

More documents

Recommendations

Info

Door lock harness, 3-pin connector 1 BLUE (+) LOCK (-) UNLOCK OUTPUT 2 EMPTY NOT USED 3 GREEN (-) LOCK (+) UNLOCK OUTPUT There are three harness connections relative to remote start function, including the heavy gauge and input and output harnesses. Heavy gauge remote start, (H3) 10-pin connector 1 PINK (+) IGNITION 1 INPUT/OUTPUT 2 RED/WHITE (30A) FUSED IGNITION 2 / FLEX RELAY INPUT 87 3 ORANGE ACCESSORY OUTPUT 4 VIOLET (+) STARTER OUTPUT (CAR SIDE OF THE STARTER KILL WIRE) 5 GREEN (+) STARTER INPUT (KEY SIDE OF THE STARTER KILL WIRE) 6 RED (+) FUSED (30A) IGNITION 1 INPUT 7 PINK/WHITE (+) IGNITION 2 / FLEX RELAY OUTPUT 8 PINK/BLACK FLEX RELAY INPUT 87A key side (if required) of FLEX RELAY 9 RED/BLACK FUSED (30A) ACCESSORY/STARTER INPUT 10 N/C N/C Remote start input, 5-pin connector 1 BLACK/WHITE (-) NEUTRAL SAFETY SWITCH INPUT 2 VIOLET/WHITE TACHOMETER INPUT WIRE 3 BROWN (+) BRAKE SHUTDOWN WIRE 4 GRAY N/O or N/C (-) HOOD PIN SWITCH INPUT, ZONE 6 5 BLUE/WHITE (-) 200 mA 2ND STATUS/REAR DEFOGGER 22 © 2008 Directed Electronics—all rights reserved
Remote start auxiliary output, 5-pin 1 PINK/WHITE (-) 200mA FLEX RELAY CONTROL OUTPUT 2 ORANGE (-) 200mA ACCESSORY OUTPUT 3 VIOLET (-) 200mA STARTER OUTPUT 4 PINK (-) 200mA IGNITION 1 OUTPUT 5 BLUE (-) 200mA STATUS OUTPUT Note: Wires 1 - 4 on the remote auxiliary outputs are wired to the (-) triggers for the onboard remote start relays and are not diode isolated. If wiring these wires directly to the vehicle you must place a 1-amp diode in line to prevent feedback from the vehicle. © 2008 Directed Electronics—all rights reserved 23
Page 1 and 2: Responder LE Model 5701 Security an
Page 3 and 4: Table of contents What is included
Page 5 and 6: What is included • The control mo
Page 7 and 8: • After the remote start module h
Page 9 and 10: After the installation • Test all
Page 11 and 12: Control module Some things to remem
Page 13 and 14: Finding the wires you need Now that
Page 15 and 16: Starter wire The starter wire provi
Page 17 and 18: Wait-to-start bulb wire for diesels
Page 19 and 20: Door pin switch circuit The best pl
Page 21: Primary harness (H1), 12-pin connec
Page 25 and 26: H1/3 BROWN (+) Siren output Connect
Page 27 and 28: H1/6 VIOLET (+) Door trigger input,
Page 29 and 30: H1/11 WHITE Parking light output Th
Page 31 and 32: H2/4 VIOLET/BLACK 200 mA (-) progra
Page 33 and 34: (+)WAIT-TO-START WIRE H2/8 BROWN/BL
Page 35 and 36: Type A: Three-wire (+) pulse contro
Page 37 and 38: Type C: Direct-wired reversing pola
Page 39 and 40: Type E: Electrically-activated vacu
Page 41 and 42: Type G: Positive (+) multiplex The
Page 43 and 44: Determining the Proper Resistor Val
Page 45 and 46: H3/8 PINK/BLACK - 87a of Ignition 2
Page 47 and 48: Outputs for optional ext. remote st
Page 49 and 50: Testing the neutral safety switch 1
Page 51 and 52: Plug-in LED and valet/program switc
Page 53 and 54: Tach learning To learn the tach sig
Page 55 and 56: Setting the light flash polarity Li
Page 57 and 58: 3. Choose. Within 10 seconds, press
Page 59 and 60: The remote control buttons that ope
Page 61 and 62: 4. Select a Feature. Press and rele
Page 63 and 64: Feature menus Menu 1 - Security fea
Page 65 and 66: Menu 3 - Remote start features Menu
Page 67 and 68: 1-5 IGNITION LOCKS OFF : (1) When t
Page 69 and 70: Menu 2 - Convenience features Defau
Page 71 and 72: 2-10 Channel 1 Linking, None (1) Ar
Page 73 and 74:
To activate manually a push button
Page 75 and 76:
Bitwriter® features The Bitwriter
Page 77 and 78:
Valet mode To enter or exit valet m
Page 79 and 80:
Timer Mode This unit can be program
Page 81 and 82:
Table of zones When using the Diagn
Page 83 and 84:
Remote starting diagnostics When th
Page 85 and 86:
Troubleshooting Alarm • Shock sen
Page 87 and 88:
6. Check connections. The heavy gau
Page 89 and 90:
Responder LE Quick Reference Wiring
show all

Responder LE Model 5701 Security and Remote Start Installation ...

Create successful ePaper yourself

Delete template?

Save as template?