Responder LE Model 5701 Security and Remote Start Installation ...

More documents

Recommendations

Info

■ If the starter engages, immediately step on the brake to shut down the system. If it does engage, recheck the neutral safety input connection. The vehicle may use a mechanical neutral safety switch. (See H3/1 BLACK/WHITE neutral safety switch input in Remote Start Harness Wire Connection Guide section of this guide.) ■ If the starter does not engage, the test is complete. Once the system passes the three tests, the vehicle can be re-assembled and delivered. Do not the use the remote start system or finalize the installation if it fails any of the safety check tests. 84 © 2008 Directed Electronics—all rights reserved
Troubleshooting Alarm • Shock sensor doesn't trigger the alarm: Has the NPC® system been triggered If so, you will hear 5 chirps when disarming. To check this, turn the ignition key on and off to clear the NPC®'s memory, and then retest the shock sensor. For a detailed description of NPC®, see Nuisance Prevention Circuitry section of this guide. • Door input does not immediately trigger full alarm. Instead, chirps are heard for the first 3 seconds: That's how the progressive two-stage door input works! This is a feature of this system. This is an instant trigger, remember, even if the door is instantly closed again, the progression from chirps to constant siren will continue. • Closing the door triggers the system, but opening the door does not: Have you correctly identified the type of door switch system This happens often when the wrong door input has been used. (See Door Lock Harness Wire Connection Guide section of this guide.) • System will not passively arm until it is remotely armed and then disarmed: Are the door inputs connected Is the H1/6 blue wire connected to the door trigger wire in the vehicle Either the H1/5 green or the H1/7 violet should be used instead. (See wiring diagrams.) • Door input does not respond with the progressive trigger, but with immediate full alarm: Does the Status LED indicate that the trigger was caused by the shock sensor (See Diagnostics section of this guide.) The shock sensor, if set to extreme sensitivity, may be detecting the door unlatching before the door switch sends its signal. Reducing the sensitivity can solve this problem. © 2008 Directed Electronics—all rights reserved 85
Page 1 and 2:
Responder LE Model 5701 Security an
Page 3 and 4:
Table of contents What is included
Page 5 and 6:
What is included • The control mo
Page 7 and 8:
• After the remote start module h
Page 9 and 10:
After the installation • Test all
Page 11 and 12:
Control module Some things to remem
Page 13 and 14:
Finding the wires you need Now that
Page 15 and 16:
Starter wire The starter wire provi
Page 17 and 18:
Wait-to-start bulb wire for diesels
Page 19 and 20:
Door pin switch circuit The best pl
Page 21 and 22:
Primary harness (H1), 12-pin connec
Page 23 and 24:
Remote start auxiliary output, 5-pi
Page 25 and 26:
H1/3 BROWN (+) Siren output Connect
Page 27 and 28:
H1/6 VIOLET (+) Door trigger input,
Page 29 and 30:
H1/11 WHITE Parking light output Th
Page 31 and 32:
H2/4 VIOLET/BLACK 200 mA (-) progra
Page 33 and 34: (+)WAIT-TO-START WIRE H2/8 BROWN/BL
Page 35 and 36: Type A: Three-wire (+) pulse contro
Page 37 and 38: Type C: Direct-wired reversing pola
Page 39 and 40: Type E: Electrically-activated vacu
Page 41 and 42: Type G: Positive (+) multiplex The
Page 43 and 44: Determining the Proper Resistor Val
Page 45 and 46: H3/8 PINK/BLACK - 87a of Ignition 2
Page 47 and 48: Outputs for optional ext. remote st
Page 49 and 50: Testing the neutral safety switch 1
Page 51 and 52: Plug-in LED and valet/program switc
Page 53 and 54: Tach learning To learn the tach sig
Page 55 and 56: Setting the light flash polarity Li
Page 57 and 58: 3. Choose. Within 10 seconds, press
Page 59 and 60: The remote control buttons that ope
Page 61 and 62: 4. Select a Feature. Press and rele
Page 63 and 64: Feature menus Menu 1 - Security fea
Page 65 and 66: Menu 3 - Remote start features Menu
Page 67 and 68: 1-5 IGNITION LOCKS OFF : (1) When t
Page 69 and 70: Menu 2 - Convenience features Defau
Page 71 and 72: 2-10 Channel 1 Linking, None (1) Ar
Page 73 and 74: To activate manually a push button
Page 75 and 76: Bitwriter® features The Bitwriter
Page 77 and 78: Valet mode To enter or exit valet m
Page 79 and 80: Timer Mode This unit can be program
Page 81 and 82: Table of zones When using the Diagn
Page 83: Remote starting diagnostics When th
Page 87 and 88: 6. Check connections. The heavy gau
Page 89 and 90: Responder LE Quick Reference Wiring
show all

Responder LE Model 5701 Security and Remote Start Installation ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?