Responder LE Model 5701 Security and Remote Start Installation ...

More documents

Recommendations

Info

Installation points to remember This product is designed for fuel-injected, automatic transmission, or vehicles with manual transmissions. Note: The default option “Manual” is a safety precaution that forces the installer to enable the Manual Transmission Mode (MTS) routine or program the unit to the “Automatic” option before the remote start can be activated for the first time. The “Automatic” option will need to be programmed On to work with automatic transmissions. When the “Manual” option is selected a specific routine is required before exiting the vehicle to enable the MTS mode. Before beginning the installation • Please read this entire installation guide before beginning the installation. The installation of this remote start system requires interfacing with many of the vehicle’s systems. Many new vehicles use low-voltage or multiplexed systems that can be damaged by low resistance testing devices, such as test lights and logic probes (computer safe test lights). Test all circuits with a high quality digital multi-meter before making connections. • Do not disconnect the battery if the vehicle has an anti-theft-coded radio. If equipped with an air bag, avoid disconnecting the battery if possible. Many airbag systems will display a diagnostic code through their warning lights after they lose power. Disconnecting the battery requires this code to be erased, which can require a trip to the dealer. • If using an external LED or Valet Switch, check with the customer about where to locate the switch. • To avoid accidental battery drainage; turn off the interior lights or remove the dome light fuse. • Roll down a window to avoid being locked out of the car. © 2008 Directed Electronics—all rights reserved
After the installation • Test all functions. The “Using Your System” section of the Owner's Guide is very helpful when testing. • When testing, don’t forget that this system is equipped with Nuisance Prevention® Circuitry (NPC). NPC can bypass trigger zones, making them appear to stop working. See the Nuisance Prevention® Circuitry section. • Review and complete the Safety Check section of this guide prior to the vehicle reassembly. © 2008 Directed Electronics—all rights reserved
Page 1 and 2: Responder LE Model 5701 Security an
Page 3 and 4: Table of contents What is included
Page 5 and 6: What is included • The control mo
Page 7: • After the remote start module h
Page 11 and 12: Control module Some things to remem
Page 13 and 14: Finding the wires you need Now that
Page 15 and 16: Starter wire The starter wire provi
Page 17 and 18: Wait-to-start bulb wire for diesels
Page 19 and 20: Door pin switch circuit The best pl
Page 21 and 22: Primary harness (H1), 12-pin connec
Page 23 and 24: Remote start auxiliary output, 5-pi
Page 25 and 26: H1/3 BROWN (+) Siren output Connect
Page 27 and 28: H1/6 VIOLET (+) Door trigger input,
Page 29 and 30: H1/11 WHITE Parking light output Th
Page 31 and 32: H2/4 VIOLET/BLACK 200 mA (-) progra
Page 33 and 34: (+)WAIT-TO-START WIRE H2/8 BROWN/BL
Page 35 and 36: Type A: Three-wire (+) pulse contro
Page 37 and 38: Type C: Direct-wired reversing pola
Page 39 and 40: Type E: Electrically-activated vacu
Page 41 and 42: Type G: Positive (+) multiplex The
Page 43 and 44: Determining the Proper Resistor Val
Page 45 and 46: H3/8 PINK/BLACK - 87a of Ignition 2
Page 47 and 48: Outputs for optional ext. remote st
Page 49 and 50: Testing the neutral safety switch 1
Page 51 and 52: Plug-in LED and valet/program switc
Page 53 and 54: Tach learning To learn the tach sig
Page 55 and 56: Setting the light flash polarity Li
Page 57 and 58: 3. Choose. Within 10 seconds, press
Page 59 and 60:
The remote control buttons that ope
Page 61 and 62:
4. Select a Feature. Press and rele
Page 63 and 64:
Feature menus Menu 1 - Security fea
Page 65 and 66:
Menu 3 - Remote start features Menu
Page 67 and 68:
1-5 IGNITION LOCKS OFF : (1) When t
Page 69 and 70:
Menu 2 - Convenience features Defau
Page 71 and 72:
2-10 Channel 1 Linking, None (1) Ar
Page 73 and 74:
To activate manually a push button
Page 75 and 76:
Bitwriter® features The Bitwriter
Page 77 and 78:
Valet mode To enter or exit valet m
Page 79 and 80:
Timer Mode This unit can be program
Page 81 and 82:
Table of zones When using the Diagn
Page 83 and 84:
Remote starting diagnostics When th
Page 85 and 86:
Troubleshooting Alarm • Shock sen
Page 87 and 88:
6. Check connections. The heavy gau
Page 89 and 90:
Responder LE Quick Reference Wiring
show all

Responder LE Model 5701 Security and Remote Start Installation ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?