Responder LE Model 5701 Security and Remote Start Installation ...

More documents

Recommendations

Info

Manual transmission remote start If the vehicle has manual transmission the proper steps must be followed before leaving the parked vehicle or the remote start feature is disabled. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Make sure the doors on the vehicle are closed. Put the transmission in neutral. Press on the brake in the vehicle. Apply the emergency brake. Release the brake. Within 15 seconds activate the remote start from the remote. The parking lights will flash confirming that the remote start is active. Turn off the ignition (the car should stay running when key is turned off). Exit the vehicle. Arm the alarm (the vehicle should shut off when arming the system). You can now remote start the vehicle. If a door is opened or if the alarm is triggered before the next remote start activation the system will not remote start. Note: To enable Valet take-over with a manual transmission, open the door and enter into manual transmission mode, as described above. Once you exit the vehicle you can arm the alarm and the car will stay running. If the vehicle shuts down when arming, then the unit did not enter valet take-over mode. 78 © 2008 Directed Electronics—all rights reserved
Timer Mode This unit can be programmed to start and run the engine every three hours, for a maximum of six cycles. The engine will run for the programmed run time and then shut down. After three hours, the system will restart the engine. Important! Timer Mode should be used only in open areas. Never start and run the vehicle in an enclosed space such as a garage or carport. To enter or exit timer mode with the transmitter: 1. Remote start the vehicle by pressing twice and then press . 2. 3. The parking lights will flash rapidly four times. After 1 second the car will start and the timer mode will run for the specified time period. The engine may run for its programmed run time, or the transmitter can be used to shut down the engine. Either way, the remote start system will restart the engine again in three hours. Timer Mode is exited automatically after the sixth run cycle. The same procedure may be used to enter or exit Timer Mode using the remote transmitter and will slowly flash the parking lights 4 times when exiting. To exit timer mode manually: 1. Make sure the remote start system is not operating the engine. 2. Turn the ignition on. Timer Mode will be exited and the parking lights will flash slowly four times. To enter turbo timer mode with a manual transmission: Perform the manual transmission procedure (See p.78), with the door open. Transmit the timer mode feature with the remote by pressing two-times, and then . After exiting the vehicle, arm the alarm and the vehicle will remain running for the programmed runtime. (The remote start feature is still enabled). Note: The Bitwriter can change the amount of times the remote start will activate and the intervals between activations in timer mode. © 2008 Directed Electronics—all rights reserved 79
Page 1 and 2:
Responder LE Model 5701 Security an
Page 3 and 4:
Table of contents What is included
Page 5 and 6:
What is included • The control mo
Page 7 and 8:
• After the remote start module h
Page 9 and 10:
After the installation • Test all
Page 11 and 12:
Control module Some things to remem
Page 13 and 14:
Finding the wires you need Now that
Page 15 and 16:
Starter wire The starter wire provi
Page 17 and 18:
Wait-to-start bulb wire for diesels
Page 19 and 20:
Door pin switch circuit The best pl
Page 21 and 22:
Primary harness (H1), 12-pin connec
Page 23 and 24:
Remote start auxiliary output, 5-pi
Page 25 and 26:
H1/3 BROWN (+) Siren output Connect
Page 27 and 28: H1/6 VIOLET (+) Door trigger input,
Page 29 and 30: H1/11 WHITE Parking light output Th
Page 31 and 32: H2/4 VIOLET/BLACK 200 mA (-) progra
Page 33 and 34: (+)WAIT-TO-START WIRE H2/8 BROWN/BL
Page 35 and 36: Type A: Three-wire (+) pulse contro
Page 37 and 38: Type C: Direct-wired reversing pola
Page 39 and 40: Type E: Electrically-activated vacu
Page 41 and 42: Type G: Positive (+) multiplex The
Page 43 and 44: Determining the Proper Resistor Val
Page 45 and 46: H3/8 PINK/BLACK - 87a of Ignition 2
Page 47 and 48: Outputs for optional ext. remote st
Page 49 and 50: Testing the neutral safety switch 1
Page 51 and 52: Plug-in LED and valet/program switc
Page 53 and 54: Tach learning To learn the tach sig
Page 55 and 56: Setting the light flash polarity Li
Page 57 and 58: 3. Choose. Within 10 seconds, press
Page 59 and 60: The remote control buttons that ope
Page 61 and 62: 4. Select a Feature. Press and rele
Page 63 and 64: Feature menus Menu 1 - Security fea
Page 65 and 66: Menu 3 - Remote start features Menu
Page 67 and 68: 1-5 IGNITION LOCKS OFF : (1) When t
Page 69 and 70: Menu 2 - Convenience features Defau
Page 71 and 72: 2-10 Channel 1 Linking, None (1) Ar
Page 73 and 74: To activate manually a push button
Page 75 and 76: Bitwriter® features The Bitwriter
Page 77: Valet mode To enter or exit valet m
Page 81 and 82: Table of zones When using the Diagn
Page 83 and 84: Remote starting diagnostics When th
Page 85 and 86: Troubleshooting Alarm • Shock sen
Page 87 and 88: 6. Check connections. The heavy gau
Page 89 and 90: Responder LE Quick Reference Wiring
show all

Responder LE Model 5701 Security and Remote Start Installation ...

Create successful ePaper yourself

Delete template?

Save as template?