Responder LE Model 5701 Security and Remote Start Installation ...

More documents

Recommendations

Info

Shutdown diagnostics To perform shutdown diagnostics 1. 2. 3. 4. With the ignition OFF, press and hold the Valet/Program switch. Turn the ignition ON and then back OFF while holding the Valet/Program switch. Release the Valet/Program switch. Press and release the Valet/Program switch. The LED starts flashing to report the last shutdown for one minute or until the ignition is turned on, as shown in the following table: LED Flashes Shutdown Mode 1 Runtime expired 2 Over-rev shutdown 3 Low or no RPM 4 Transmitter shutdown (or optional push button) 5 (+) Brake shutdown 6 (-) Hood shutdown 7 Timer mode/Turbo mode/Manual mode error * 8 Neutral safety shutdown 9 Low battery (voltage mode) 10 Alarm triggered ** 11 Wait-to-start input timed out *Timer mode error: Ignition is on or shutdown input is active when activating timer mode. Turbo mode error: Turbo mode is programmed off, engine is not on or shutdown input is active. Manual mode error: MTS mode not enabled. ** Alarm was triggered during remote start sequence. 82 © 2008 Directed Electronics—all rights reserved
Remote starting diagnostics When the remote start function is activated and emits an error tone; you have the ability to see what the cause of the no-start situation is by counting the amount of flashes of the parking lights from the vehicle. 5 flashes - Brake wire is active 6 flashes - Hoodpin wire is active 7 flashes - Manual transmission mode is enabled and not initialized. 8 flashes - Neutral safety wire has no ground or the neutral safety is Off. Remote start safety check Before vehicle reassembly, the remote system must be checked to ensure safe and trouble-free operation. The following test procedure must be used to verify proper installation and operation of the system. The installation must be completed before testing, including connection to the brake switch and hood switch. 1. Test the BRAKE shutdown circuit: With the vehicle in Park (P), activate the remote start system. Once the engine is running, press the brake pedal. The engine should shut down immediately. If the engine continues to run, check the brake circuit connection. 2. Test the HOOD PIN shutdown circuit: With the vehicle in Park (P), open the hood. Activate the remote start system. The vehicle should not start. If the starter engages, check your hood pin and connections. 3. Test the NEUTRAL SAFETY shutdown circuit. Important! Make sure there is adequate clearance to the front and rear of the vehicle before attempting this test. 1. Make sure the hood is closed and no other shutdown circuits are active. 2. Set the emergency brake. 3. Turn the ignition key to the run position but do not start the engine. 4. Put the vehicle in Drive (D). 5. Put your foot over the brake pedal but do not press down on it. Be ready to step on the brake to shutdown the remote start system. 6. Activate the remote start system. © 2008 Directed Electronics—all rights reserved 83
Page 1 and 2:
Responder LE Model 5701 Security an
Page 3 and 4:
Table of contents What is included
Page 5 and 6:
What is included • The control mo
Page 7 and 8:
• After the remote start module h
Page 9 and 10:
After the installation • Test all
Page 11 and 12:
Control module Some things to remem
Page 13 and 14:
Finding the wires you need Now that
Page 15 and 16:
Starter wire The starter wire provi
Page 17 and 18:
Wait-to-start bulb wire for diesels
Page 19 and 20:
Door pin switch circuit The best pl
Page 21 and 22:
Primary harness (H1), 12-pin connec
Page 23 and 24:
Remote start auxiliary output, 5-pi
Page 25 and 26:
H1/3 BROWN (+) Siren output Connect
Page 27 and 28:
H1/6 VIOLET (+) Door trigger input,
Page 29 and 30:
H1/11 WHITE Parking light output Th
Page 31 and 32: H2/4 VIOLET/BLACK 200 mA (-) progra
Page 33 and 34: (+)WAIT-TO-START WIRE H2/8 BROWN/BL
Page 35 and 36: Type A: Three-wire (+) pulse contro
Page 37 and 38: Type C: Direct-wired reversing pola
Page 39 and 40: Type E: Electrically-activated vacu
Page 41 and 42: Type G: Positive (+) multiplex The
Page 43 and 44: Determining the Proper Resistor Val
Page 45 and 46: H3/8 PINK/BLACK - 87a of Ignition 2
Page 47 and 48: Outputs for optional ext. remote st
Page 49 and 50: Testing the neutral safety switch 1
Page 51 and 52: Plug-in LED and valet/program switc
Page 53 and 54: Tach learning To learn the tach sig
Page 55 and 56: Setting the light flash polarity Li
Page 57 and 58: 3. Choose. Within 10 seconds, press
Page 59 and 60: The remote control buttons that ope
Page 61 and 62: 4. Select a Feature. Press and rele
Page 63 and 64: Feature menus Menu 1 - Security fea
Page 65 and 66: Menu 3 - Remote start features Menu
Page 67 and 68: 1-5 IGNITION LOCKS OFF : (1) When t
Page 69 and 70: Menu 2 - Convenience features Defau
Page 71 and 72: 2-10 Channel 1 Linking, None (1) Ar
Page 73 and 74: To activate manually a push button
Page 75 and 76: Bitwriter® features The Bitwriter
Page 77 and 78: Valet mode To enter or exit valet m
Page 79 and 80: Timer Mode This unit can be program
Page 81: Table of zones When using the Diagn
Page 85 and 86: Troubleshooting Alarm • Shock sen
Page 87 and 88: 6. Check connections. The heavy gau
Page 89 and 90: Responder LE Quick Reference Wiring
show all

Responder LE Model 5701 Security and Remote Start Installation ...

Create successful ePaper yourself

Delete template?

Save as template?