Responder LE Model 5701 Security and Remote Start Installation ...

More documents

Recommendations

Info

• The vehicle will start, but will only run for 10 seconds. 1. 2. Is the remote start programmed for voltage sense If this does not work, a tach wire should be used. Check diagnostics. • The climate control system does not work while the unit is operating the vehicle. Either the wrong accessory wire is being energized or more than one ignition or accessory wire must be energized in order to operate the climate control system. 88 © 2008 Directed Electronics—all rights reserved
Responder LE Quick Reference Wiring Guide D2D jumpers: must be horizontal For connecting to external modules for use with external module. Antenna four-pin connector Red/White aux trunk release (-) 200mA Red 12v (+) constant input Brown siren (+) output White/Brown Flex parking light relay 87A Black chassis ground Violet door (+) input Blue trunk (-) instant trigger input Greendoor (-) input Black/white domelight 200mA (-) output White/Blue remote start activation(-) input White parking light output 30 Orange ground-when-armed (-) 500mA output IMPORTANT! Neutral safety must be plugged in and in the On position. ON D2D Data-to-data connector Black/White neutral safety (-) input Violet/White tach input Brown brake shut down (+) input H1 Bitwriter ESP Tach Threshold Jumper Hi Lo Neutral Safety Switch RS in Access Door Light Flash Fuse Jumper under door. Use needlenose pliers to change fuse position. Door Lock/unlock Status LED Output (use White two-pin from antenna cable) Valet Program switch input (use Blue two-pin from antenna cable) Blue RS status (-) 200mA output Pink RS ignition1 (-) 200mA output Violet RS starter (-) 200mA output Orange RS accessory (-) 200mA output Pink ignition 1 (+) output (also ignition sense input) Red/white fused 30a (contact 87 of RS Flex Relay) Orange accessory output Violet starter output (car side of starter wire) Green starter input (key side of starter wire) Red 12V(+) constant fused 30a input (for Ignition1 relay) Pink/ White Flex Relay output (default is ignition 2) Pink/black Flex Relay contact 87a (default is ignition 2) Red/black fused 30a( for accessory and starter relays) Remote start output Optional Mux sensor port H2 Relay out H3 Pink/ White flex (-) 200mA output (default setting is ignition 2) Note: Wires 1 - 4 on the auxiliary outputs are wired to the (-) triggers for the onboard remote start relays and are not diode isolated. If wiring directly to the vehicle place a 1-amp diode in line to prevent feedback from the vehicle. Green Blue (-) Lock (+) Unlock Gray hood pin switch NO/NC (-) input (-) Unlock (+) Lock Blue/White 2nd remote start status (-) 200mA output Defogger (programmable) Heavy gauge 10-pin connection rear view N/C RED/BLACK PINK/BLACK PINK/WHITE RED Light Green/ Black OEM disarm (-) 200mA output Light Green/ White OEM arm (-) 200mA output 10 9 8 7 6 White/ Violet AUX 1 (-) 200mA output PINK RED/WHITE Violet/Black AUX 2 (-) 200mA output ORANGE White/ Black AUX 3(-) 200mA output VIOLET Light Blue 2nd Unlock (-) 200mA output GREEN Gray/ Black wait-to-start (-) input Brown/Black (-) 200mA Horn honk output © 2008 Directed Electronics 5 4 3 2 1 © 2008 Directed Electronics—all rights reserved 89
Page 1 and 2:
Responder LE Model 5701 Security an
Page 3 and 4:
Table of contents What is included
Page 5 and 6:
What is included • The control mo
Page 7 and 8:
• After the remote start module h
Page 9 and 10:
After the installation • Test all
Page 11 and 12:
Control module Some things to remem
Page 13 and 14:
Finding the wires you need Now that
Page 15 and 16:
Starter wire The starter wire provi
Page 17 and 18:
Wait-to-start bulb wire for diesels
Page 19 and 20:
Door pin switch circuit The best pl
Page 21 and 22:
Primary harness (H1), 12-pin connec
Page 23 and 24:
Remote start auxiliary output, 5-pi
Page 25 and 26:
H1/3 BROWN (+) Siren output Connect
Page 27 and 28:
H1/6 VIOLET (+) Door trigger input,
Page 29 and 30:
H1/11 WHITE Parking light output Th
Page 31 and 32:
H2/4 VIOLET/BLACK 200 mA (-) progra
Page 33 and 34:
(+)WAIT-TO-START WIRE H2/8 BROWN/BL
Page 35 and 36:
Type A: Three-wire (+) pulse contro
Page 37 and 38: Type C: Direct-wired reversing pola
Page 39 and 40: Type E: Electrically-activated vacu
Page 41 and 42: Type G: Positive (+) multiplex The
Page 43 and 44: Determining the Proper Resistor Val
Page 45 and 46: H3/8 PINK/BLACK - 87a of Ignition 2
Page 47 and 48: Outputs for optional ext. remote st
Page 49 and 50: Testing the neutral safety switch 1
Page 51 and 52: Plug-in LED and valet/program switc
Page 53 and 54: Tach learning To learn the tach sig
Page 55 and 56: Setting the light flash polarity Li
Page 57 and 58: 3. Choose. Within 10 seconds, press
Page 59 and 60: The remote control buttons that ope
Page 61 and 62: 4. Select a Feature. Press and rele
Page 63 and 64: Feature menus Menu 1 - Security fea
Page 65 and 66: Menu 3 - Remote start features Menu
Page 67 and 68: 1-5 IGNITION LOCKS OFF : (1) When t
Page 69 and 70: Menu 2 - Convenience features Defau
Page 71 and 72: 2-10 Channel 1 Linking, None (1) Ar
Page 73 and 74: To activate manually a push button
Page 75 and 76: Bitwriter® features The Bitwriter
Page 77 and 78: Valet mode To enter or exit valet m
Page 79 and 80: Timer Mode This unit can be program
Page 81 and 82: Table of zones When using the Diagn
Page 83 and 84: Remote starting diagnostics When th
Page 85 and 86: Troubleshooting Alarm • Shock sen
Page 87: 6. Check connections. The heavy gau
show all

Responder LE Model 5701 Security and Remote Start Installation ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?