PMS 4500 FCB Manual - Ysebaert

More documents

Recommendations

Info

Mode of Operation of the Generator 1. Raw water impeller pump 2. Freshwater pump 3. Water-cooled exhaust elbow 4. Cooling water connection block 5. Heat exchanger 6. Raw water filter 7. Water cock 8. Raw water inlet 9. Expansion tank 10. Vent valve 11. Oil cooler 12. Reducer Page 12 PMS_4500_FCB_manual.V02 - Chapter A: Mode of Operation of the Generator 15.7.05
Maintenance Instructions B. Maintenance Instructions B.1 General maintenance instructions B.1.1 Checks before starting • Oil level • Cooling system leaks • Visual check for any changes, leaks oil drain system, v-belt, cable connections, hose clips, air filter, fuel lines B.1.2 Hose elements and rubber formed component in the sound cover Check all hoses and hose connections for good condition. The rubber hoses are very sensitive to enviromental influences. They can season fast with dry air, in which environment of muted oil and fuel steams and increased temperature. The hoses must be checked regularly for elasticity. There are operating situations, at which the hoses must be renewed once in the year. Additionally to usual tasks of maintenance (oil level check, oil filter control etc.) further maintenance activities are to be accomplished for marine aggregates. It belongs control of the sacrificial anode (cooling water connection block) and the front seal cover at the generator. For maintenance intervalls see Table F.5, “Inspection checklist for services,” on Page VIII. B.2 Oil circuit maintenance The first oil change is to be accomplished after a period of operation from 35 to 50 hours. Afterwards the oil is to be changed after 100 hours. For this the oil SAE30 for temperatures over 20°C and SAE20 for temperatures between 5°C and 20°C is to be used. At temperatures under 5°C oil of the viscosity SAE10W or 10W-30 is prescribed. Type and amount of required oil see: See “Engine oil” on page IX and “Technical Data Engine” on page V. 15.7.05 PMS_4500_FCB_manual.V02 - Chapter B: Maintenance Instructions Page 13
Page 1 and 2: Installation manual Installation, M
Page 3 and 4: 25 20 10 10 10 since 1977 Icemaster
Page 5: Safety Instructions The electrical
Page 8 and 9: C.3 Low Generator-Output Voltage ..
Page 10 and 11: Page 4 PMS_4500_FCB_manual.V02 - Ta
Page 12 and 13: Mode of Operation of the Generator
Page 20 and 21: Maintenance Instructions B.3 Execut
Page 22 and 23: Maintenance Instructions B.3.1 De-a
Page 24 and 25: Maintenance Instructions B.5 De-aer
Page 26 and 27: Maintenance Instructions If no chan
Page 28 and 29: Maintenance Instructions B.7 Causes
Page 30 and 31: Maintenance Instructions B.8 Coolan
Page 32 and 33: Maintenance Instructions B.9.1 Meas
Page 34 and 35: Generator Failure Overloading the G
Page 36 and 37: Generator Failure Steps to check th
Page 38 and 39: Generator Failure C.3.3 Checking th
Page 40 and 41: Generator Failure C.4 Generator pro
Page 42 and 43: Generator Failure Damage to starter
Page 44 and 45: Installation Instructions D.2 Gener
Page 46 and 47: Installation Instructions D.3.4 Ins
Page 50 and 51: Installation Instructions D.4 The F
Page 52 and 53: Installation Instructions ’Ventil
Page 54 and 55: Installation Instructions D.5 Water
Page 58 and 59: Installation Instructions D.6.2 The
Page 60 and 61: Installation Instructions D.7 Gener
Page 62 and 63: Installation Instructions D.7.3 The
Page 66 and 67: Installation Instructions D.8.3 AC-
Page 68 and 69:
Installation Instructions D.8.5 Jum
Page 70 and 71:
Installation Instructions A) upper
Page 72 and 73:
Troubleshooting DIESEL MOTOR FAILS
Page 74 and 75:
Troubleshooting MOTOR STOPS BY ITSE
Page 76 and 77:
Technical Data Generator F.3 Techni
Page 78 and 79:
Inspection checklist for services F
Page 80 and 81:
Coolant F.7 Coolant Use a mixture o
Page 82 and 83:
Cooling water flow Panda 4500 FCB F
Page 84:
WHEN AN ADULT STOPS BREATHING WARNI
show all

PMS 4500 FCB Manual - Ysebaert

Create successful ePaper yourself

Delete template?

Save as template?