PMS 4500 FCB Manual - Ysebaert

More documents

Recommendations

Info

Installation Instructions D.7.3 The speed sensor Speed sensor Installation of the speed sensor The speed sensor tip must have between 0.3 to 0.8mm of clearance (air gap) from the gear tooth tips. In order to achieve this clearance: the speed sensor tip should be aligned with the tip of a gear tooth and screwed in until it touches the tip of the tooth. (ATTENTION! Ensure that when inserting the sensor, that the sensor tip is not screwed into the root of the gear tooth). The screw is subsequently turned anticlockwise by half a turn (0.3 to 0.8mm) and held by a counter nut. 4 1 1. Speed sensor on threaded seat 2. Engine Flywheel (with gear teeth) 3. Generator housing 4. Retention/tightening nut 2 3 1 1 2 2 1. Speed sensor on threaded seat 2. Engine Flywheel (with gear teeth) D.7.4 Electronic starter control unit If there is an automatic starting requirement and if the remote control panel is switched off, then this automatic starting requirement is ignored. Automatic starting is only possible if after switching on of the remote control panel the automatic starting requirement takes place. Page 56 PMS_4500_FCB_manual.V02 - Chapter D: Installation Instructions 15.7.05
Installation Instructions D.8 Generator AC System-Installation ATTENTION! Before the electrical system is installed, READ the “Safety Instructions” on page v of this manual FIRST! Be sure that all electrical installations (including all safety systems) comply with all required regulations of the regional authorities. This includes lightnening conductor, personal protection switch etc. D.8.1 Installation with looped in AC-Control box 1. Generator 2. Starter battery 3. AC-Control box 4. Distribustion panel 5. Remote control panel 6. Fuel pump All electrical safety installations have to be made on board. 15.7.05 PMS_4500_FCB_manual.V02 - Chapter D: Installation Instructions Page 57
Page 1 and 2:
Installation manual Installation, M
Page 3 and 4:
25 20 10 10 10 since 1977 Icemaster
Page 5:
Safety Instructions The electrical
Page 8 and 9:
C.3 Low Generator-Output Voltage ..
Page 10 and 11:
Page 4 PMS_4500_FCB_manual.V02 - Ta
Page 12 and 13: Mode of Operation of the Generator
Page 20 and 21: Maintenance Instructions B.3 Execut
Page 22 and 23: Maintenance Instructions B.3.1 De-a
Page 24 and 25: Maintenance Instructions B.5 De-aer
Page 26 and 27: Maintenance Instructions If no chan
Page 28 and 29: Maintenance Instructions B.7 Causes
Page 30 and 31: Maintenance Instructions B.8 Coolan
Page 32 and 33: Maintenance Instructions B.9.1 Meas
Page 34 and 35: Generator Failure Overloading the G
Page 36 and 37: Generator Failure Steps to check th
Page 38 and 39: Generator Failure C.3.3 Checking th
Page 40 and 41: Generator Failure C.4 Generator pro
Page 42 and 43: Generator Failure Damage to starter
Page 44 and 45: Installation Instructions D.2 Gener
Page 46 and 47: Installation Instructions D.3.4 Ins
Page 50 and 51: Installation Instructions D.4 The F
Page 52 and 53: Installation Instructions ’Ventil
Page 54 and 55: Installation Instructions D.5 Water
Page 58 and 59: Installation Instructions D.6.2 The
Page 60 and 61: Installation Instructions D.7 Gener
Page 66 and 67: Installation Instructions D.8.3 AC-
Page 68 and 69: Installation Instructions D.8.5 Jum
Page 70 and 71: Installation Instructions A) upper
Page 72 and 73: Troubleshooting DIESEL MOTOR FAILS
Page 74 and 75: Troubleshooting MOTOR STOPS BY ITSE
Page 76 and 77: Technical Data Generator F.3 Techni
Page 78 and 79: Inspection checklist for services F
Page 80 and 81: Coolant F.7 Coolant Use a mixture o
Page 82 and 83: Cooling water flow Panda 4500 FCB F
Page 84: WHEN AN ADULT STOPS BREATHING WARNI
show all

PMS 4500 FCB Manual - Ysebaert

Create successful ePaper yourself

Delete template?

Save as template?