GEA CAIRfricostar - Aspectenvironmental.com
GEA CAIRfricostar - Aspectenvironmental.com
GEA CAIRfricostar - Aspectenvironmental.com
- No tags were found...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>GEA</strong> <strong>CAIRfricostar</strong><br />
Dehumidification unit with air mixing and heat pump function<br />
Type CMU<br />
Heat pump for<br />
dehumidification:<br />
– Direct evaporator according to VDI 6022: heat exchanger as Cu/Alu model for R<br />
407c refrigerant, fins made of aluminium, frame elements made of AlMg3, pipes<br />
made of oxygen-free copper.<br />
– Condensate water tray in bottom panel for evaporator and heat recovery system,<br />
with a slope in the direction of condensate drain, made of stainless steel V4A powder<br />
coated, including drain tray, conform with VDI 6022<br />
– Air-cooled condenser according to VDI 6022: heat exchanger as Cu/Alu model for<br />
R 407c refrigerant, fins made of aluminium, frame elements made of AlMg3, pipes<br />
made of oxygen-free copper<br />
– Compressor unit: refrigeration circuit with a fully hermetic scroll <strong>com</strong>pressor<br />
– With optimized heat exchanger <strong>com</strong>bination for maximum COP values, mounted on<br />
anti-vibration mounts, circuit includes filter drier, liquid collector, thermostatic<br />
expansion valve with MOP (maximum operating pressure) and external pressure<br />
equalisation, all necessary shut-off valves, monitoring and safety devices<br />
(pressostat, icing sensor, etc.)<br />
Droplet eliminator – Made of plastic with an aluminium frame at air velocities on supply and exhaust side<br />
exceeding 2,5 m/s is necessary<br />
Air mixing dehumidifier CMU<br />
Fan unit:<br />
Alternative fan unit:<br />
<strong>GEA</strong> centrifugal fan „LESS ENERGY SYSTEM“<br />
– Optimized operating point, double side suction, coated surface model<br />
– Three phase motor, protection class IP55 , model type B3, <strong>com</strong>plete belt drive, easy<br />
service thanks to one bolt tensioning sled<br />
– Fan/motor unit mounted on anti-vibration mounts<br />
<strong>GEA</strong> „OPTIVENT“ high performance fan impellers<br />
– Surface coated one side suction with backward curved blades that are directly connected<br />
to motor shaft; performance optimized three-phase motor, B3 model type,<br />
protection type IP55, insulation class F adjusted for operation with a frequency converter.<br />
Fan and motor unit including coated intake nozzle mounted on buckling<br />
resistant and coated base construction, motor and fan have sound attenuated<br />
bearings.<br />
– Continuous measurement of pressure effects<br />
– Statically and dynamically balanced according to DIN ISO 1940, part 1, G2,5).<br />
Continuous monitoring of operation using DDC. Frequency converter for each<br />
motor installed in or mounted on the unit, control via <strong>GEA</strong> DDC with a separate analogue<br />
signal for both motors. Frequency converters are adjusted and set for both<br />
motors. Limit values for motor current and fan speed are set by the programme<br />
– Resonance frequency band/fade out set by factory<br />
– Automatic energy optimization for optimal energy use and efficiency rate<br />
– Multiple motor operation is possible<br />
– Voltage intermediate circuit converter without reduction of capacity<br />
– Continuous speed control<br />
– Operating hours counter<br />
– Min. and max. speed limitation, automatic ramp curve function UP/DOWN<br />
– Automatic motor adjustment<br />
– Motor tracing switch<br />
– DC break<br />
– Variable clock frequency<br />
– Motor protection<br />
– Short circuit and short circuit to earth safe<br />
– Under and over current protection<br />
– Phase fault monitoring<br />
PR-2008-0327-GB • Subject to modifications • Status 05/2009 9