Programming Manual

More documents

Recommendations

Info

LNC-MILLG89 Reaming CycleG89 Reaming CycleCommand FormatG89 X╴ Y╴ Z╴ R╴ P╴ K╴ F╴;Argument Instruction• X__Y__Coordinate of hole position (mm).• Z__Coordinate of hole bottom (mm).• R__Coordinate of R point (i.e. retraction point) (mm).• P__Dwell time at hole bottom (1/1000 sec), minimum unit, decimal numbers arenot allowed.• K__Times of repetition.• F__Cutting feedrate (G94 mm/min) (G95 mm/rev)Action Instruction (taking G17 plane for example)1. Fast position to hole position (X, Y, yet main tain original tool height);2. Fast position to the coordinate of R point (R);3. Cut to hole bottom position (Z) with specified cutting feedrate and spindlespeed;4. If P is specified, dwell at hole bottom for specified time;5. In G98 mode, return to starting point at cutting feedrate; In G99 mode,return to R point at cutting feedrate;6. If K is specified ( > 1), repeat steps 2~5 until obtaining specified reamingrepetition times; otherwise procedure ends;148 LNC Technology Co., Ltd.
LNC-MILLG89 Reaming Cycle7. In G91 mode, argument R specifies the distance between R point and thestarting point; argument Z specifies the distance between hole bottomposition and R point; If K is specified ( > 1), after each reaming process(steps 2~5), the hole will migrate according to specified X, Y and thencontinue next reaming process.8. The difference between G85 and G89 is that the latter can specify the dwelltime at hole bottom.IllustrationWork BreakdownStarting pointR pointG89 G98)Retract toStarting pointWork BreakdownStarting pointR pointG89 (G99)Retract toR pointPZ pointPZ pointLNC Technology Co., Ltd. 149
Page 3 and 4:
LNC-MILLTable of ContentTable of Co
Page 5:
LNC-MILLTable of ContentG131 Circul
Page 9:
LNC-MILLG-Code Function TableG Code
Page 12 and 13:
LNC-MILLG00 Rapid Positioning3 Comm
Page 14 and 15:
LNC-MILLG01 Linear InterpolationG01
Page 16 and 17:
LNC-MILLG02, G03 Circular/Helical I
Page 18 and 19:
LNC-MILLG04 DwellG04 DwellCommand F
Page 20 and 21:
LNC-MILLG10 Data Input SettingG10 D
Page 22 and 23:
LNC-MILLG15 Polar Coordinate Comman
Page 24 and 25:
LNC-MILLG17, G18, G19 Cutting Plane
Page 26 and 27:
LNC-MILLG22, G23 Tool Stored Stroke
Page 28 and 29:
LNC-MILLG27 Return to Origin CheckG
Page 30 and 31:
LNC-MILLG28 Return to the First Ref
Page 32 and 33:
LNC-MILLG29 Return from the First R
Page 34 and 35:
LNC-MILLG30 Auto Return to the 2nd,
Page 36 and 37:
LNC-MILLG31 Skip Signal Abort Block
Page 38 and 39:
LNC-MILLG31 Skip Signal Abort Block
Page 40 and 41:
LNC-MILLG41, G42 Tool Radius Compen
Page 42 and 43:
LNC-MILLG43, G44, G49 Tool Length C
Page 44 and 45:
LNC-MILLG43, G44, G49 Tool Length C
Page 46 and 47:
LNC-MILLG50, G51 Scaling CommandIll
Page 48 and 49:
LNC-MILLG52 Interval Coordinate Sys
Page 50 and 51:
LNC-MILLG54~G59 Manufacturing Coord
Page 52 and 53:
LNC-MILLG61, G64 Exact Positioning
Page 54 and 55:
LNC-MILLG65 Simple CallO0001;..#1==
Page 56 and 57:
LNC-MILLG66 Macro Program Mode Call
Page 58 and 59:
LNC-MILLG67 Macro Program Mode Call
Page 60 and 61:
60°LNC-MILLG68, G69 Coordinate Sys
Page 62 and 63:
LNC-MILLG73 Rapid Peck Drilling Cyc
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
LNC-MILLG74 Left-Handed Screw Threa
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
LNC-MILLG76 Fine Boring CycleG76 Fi
Page 82 and 83:
LNC-MILLG76 Fine Boring CycleIllust
Page 84 and 85:
LNC-MILLG76 Fine Boring CycleM03 S1
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
LNC-MILLG81 Drilling CycleG81 Drill
Page 92 and 93:
LNC-MILLG81 Drilling CycleProgram S
Page 94 and 95:
LNC-MILLG81 Drilling CycleM03 S1000
Page 96 and 97:
Page 98 and 99:
LNC-MILLG82 Drilling CycleG82 Drill
Page 100 and 101:
LNC-MILLG82 Drilling CycleProgram S
Page 102 and 103:
Page 104 and 105: LNC-MILLG82 Drilling CycleM03 S1000
Page 106 and 107: LNC-MILLG83 Peck Drilling CycleG83
Page 108 and 109: LNC-MILLG83 Peck Drilling CycleProg
Page 110 and 111: LNC-MILLG83 Peck Drilling CycleM03
Page 112 and 113: LNC-MILLG83 Peck Drilling CycleM03
Page 114 and 115: LNC-MILLG84 Right-Handed Screw Thre
Page 122 and 123: LNC-MILLG85 Reaming CycleG85 Reamin
Page 124 and 125: LNC-MILLG85 Reaming CycleProgram Sa
Page 126 and 127: LNC-MILLG85 Reaming CycleM03 S1000;
Page 130 and 131: LNC-MILLG86 Boring CycleG86 Boring
Page 132 and 133: LNC-MILLG86 Boring CycleProgram Sam
Page 134 and 135: LNC-MILLG86 Boring CycleM03 S1000;G
Page 138 and 139: LNC-MILLG87 Back Boring/CuttingG87
Page 140 and 141: LNC-MILLG87 Back Boring/CuttingIllu
Page 142 and 143: LNC-MILLG87 Back Boring/CuttingM03
Page 144 and 145: LNC-MILLG87 Back Boring/CuttingM03
Page 146 and 147: LNC-MILLG88 Boring CycleG88 Boring
Page 148 and 149: LNC-MILLG88 Boring CycleProgram Sam
Page 156 and 157: LNC-MILLG89 Reaming CycleProgram Sa
Page 162 and 163: LNC-MILLG90, G91 Absolute, Incremen
Page 164 and 165: LNC-MILLG92 Coordinate SettingBNew
Page 166 and 167: LNC-MILLG98, G99 Retraction Point S
Page 168 and 169: LNC-MILLG101~G105 Compound G-Code f
Page 170 and 171: LNC-MILLG101 Linear Mode Multi-hole
Page 176 and 177: LNC-MILLG102 Circular Mode of Multi
Page 178 and 179: OLNC-MILLG102 Circular Mode of Mult
Page 184 and 185: LNC-MILLG103 Arc Mode of Multi-hole
Page 190 and 191: LNC-MILLG104 Grid Mode of Multi-hol
Page 198 and 199: LNC-MILLG105 Promiscuous Mode of Mu
Page 204 and 205:
LNC-MILLG105 Promiscuous Mode of Mu
Page 206 and 207:
LNC-MILLG111 X-axis Two-Way Plane M
Page 208 and 209:
LNC-MILLG112 Two-way Plane Processi
Page 210 and 211:
LNC-MILLG113 One-way Plane Manufact
Page 212 and 213:
LNC-MILLG114 Y One-way Plane Manufa
Page 214 and 215:
LNC-MILLG121~G123 Compound G-Code f
Page 216 and 217:
LNC-MILLG122 Rectangle Shape Side M
Page 218 and 219:
LNC-MILLG131~G133 Compound G-Code f
Page 220 and 221:
LNC-MILLG132 Rectangle Shape Fillet
Page 223 and 224:
LNC MILLIndication of Auxiliary Fun
Page 225:
LNC MILLIndication of Auxiliary Fun
Page 228 and 229:
LNC MILLMACRO Program5.2 Macro Prog
Page 230 and 231:
LNC MILLMACRO Program5.2.4 Calling
Page 232 and 233:
LNC MILLMACRO Program5.2.5 Calling
Page 234 and 235:
LNC MILLMACRO Program5.4 MACRO Func
Page 236 and 237:
LNC MILLMACRO Program5.5.2 Classifi
Page 238 and 239:
LNC MILLMACRO Program7. Coordinate
Page 240 and 241:
LNC MILLMACRO ProgramTimesInstructi
Page 242 and 243:
LNC MILLMACRO Program5.5.4 Tool Com
Page 244 and 245:
LNC MILLMACRO Program5.5.7 Instruct
Page 246 and 247:
LNC MILLMACRO Program5.8 Compare Co
Page 248 and 249:
LNC MILLMACRO Program5.10 Flow Cont
Page 250 and 251:
LNC MILLMACRO Program• DO cycle c
Page 252:
LNC MILLMACRO Program#i=FIX(#j)(unc
show all

Programming Manual

Create successful ePaper yourself

Delete template?

Save as template?