Programming Manual

More documents

Recommendations

Info

LNC-MILLG66 Macro Program Mode CallG66 Macro Program Mode CallCommand FormatG66 P__ L__ ;Argument Instruction• P__The macro program times to be called (Macro program name excluding the 4digits after “O”). The system alarm will be triggered if no input available. [INT3111: no called program name (no input of P address)].• L__Times of iteration. The default setting value is 1 if no input.In addition to arguments P and L mentioned above, more NC addresses(English alphabets excluding G, L, N, O, P) can be used to induct argumentswithout any previously defined order, and these arguments are correspondingto the local variables used in the macro program. Refer to the comparisoncharts listed in G65.Action InstructionThe difference between G66 and G65 is that the latter only calls macro program for once, but themacro programs called by G66 will be called aincremental after each movement block is completeduntil the calling mode is cancelled by G67.O0001;..G66 P0008 L1 A 2.0B3.0;G91 G00 Y10.;Y10.;Y10.;G67;Y10.;Execution O0008After Move,Execution O0008After Move,Execution O0008After Move,Execution O0008Go O0001O0008;#3=#1+#2;G91 G00 Z#3;Z-#3;M99;50 LNC Technology Co., Ltd.
LNC-MILLG66 Macro Program Mode CallIn G66 blocks, G66 must be written before all arguments. Like G65, the nest type call could be doneby G66, and up to 4 levels are available for the combination of G66 and G65, (The main program isnot included, and the main program is level 0), but the G66 arguments (corresponding to localvariables of macro program) can only be set for once in G66 block, and then the mode calling willnot be reset aincremental.LNC Technology Co., Ltd. 51
Page 3 and 4:
LNC-MILLTable of ContentTable of Co
Page 5: LNC-MILLTable of ContentG131 Circul
Page 9: LNC-MILLG-Code Function TableG Code
Page 12 and 13: LNC-MILLG00 Rapid Positioning3 Comm
Page 14 and 15: LNC-MILLG01 Linear InterpolationG01
Page 16 and 17: LNC-MILLG02, G03 Circular/Helical I
Page 18 and 19: LNC-MILLG04 DwellG04 DwellCommand F
Page 20 and 21: LNC-MILLG10 Data Input SettingG10 D
Page 22 and 23: LNC-MILLG15 Polar Coordinate Comman
Page 24 and 25: LNC-MILLG17, G18, G19 Cutting Plane
Page 26 and 27: LNC-MILLG22, G23 Tool Stored Stroke
Page 28 and 29: LNC-MILLG27 Return to Origin CheckG
Page 30 and 31: LNC-MILLG28 Return to the First Ref
Page 32 and 33: LNC-MILLG29 Return from the First R
Page 34 and 35: LNC-MILLG30 Auto Return to the 2nd,
Page 36 and 37: LNC-MILLG31 Skip Signal Abort Block
Page 38 and 39: LNC-MILLG31 Skip Signal Abort Block
Page 40 and 41: LNC-MILLG41, G42 Tool Radius Compen
Page 42 and 43: LNC-MILLG43, G44, G49 Tool Length C
Page 44 and 45: LNC-MILLG43, G44, G49 Tool Length C
Page 46 and 47: LNC-MILLG50, G51 Scaling CommandIll
Page 48 and 49: LNC-MILLG52 Interval Coordinate Sys
Page 50 and 51: LNC-MILLG54~G59 Manufacturing Coord
Page 52 and 53: LNC-MILLG61, G64 Exact Positioning
Page 54 and 55: LNC-MILLG65 Simple CallO0001;..#1==
Page 58 and 59: LNC-MILLG67 Macro Program Mode Call
Page 60 and 61: 60°LNC-MILLG68, G69 Coordinate Sys
Page 62 and 63: LNC-MILLG73 Rapid Peck Drilling Cyc
Page 72 and 73: LNC-MILLG74 Left-Handed Screw Threa
Page 80 and 81: LNC-MILLG76 Fine Boring CycleG76 Fi
Page 82 and 83: LNC-MILLG76 Fine Boring CycleIllust
Page 84 and 85: LNC-MILLG76 Fine Boring CycleM03 S1
Page 90 and 91: LNC-MILLG81 Drilling CycleG81 Drill
Page 92 and 93: LNC-MILLG81 Drilling CycleProgram S
Page 94 and 95: LNC-MILLG81 Drilling CycleM03 S1000
Page 98 and 99: LNC-MILLG82 Drilling CycleG82 Drill
Page 100 and 101: LNC-MILLG82 Drilling CycleProgram S
Page 106 and 107:
LNC-MILLG83 Peck Drilling CycleG83
Page 108 and 109:
LNC-MILLG83 Peck Drilling CycleProg
Page 110 and 111:
LNC-MILLG83 Peck Drilling CycleM03
Page 112 and 113:
LNC-MILLG83 Peck Drilling CycleM03
Page 114 and 115:
LNC-MILLG84 Right-Handed Screw Thre
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
LNC-MILLG85 Reaming CycleG85 Reamin
Page 124 and 125:
LNC-MILLG85 Reaming CycleProgram Sa
Page 126 and 127:
LNC-MILLG85 Reaming CycleM03 S1000;
Page 128 and 129:
Page 130 and 131:
LNC-MILLG86 Boring CycleG86 Boring
Page 132 and 133:
LNC-MILLG86 Boring CycleProgram Sam
Page 134 and 135:
LNC-MILLG86 Boring CycleM03 S1000;G
Page 136 and 137:
Page 138 and 139:
LNC-MILLG87 Back Boring/CuttingG87
Page 140 and 141:
LNC-MILLG87 Back Boring/CuttingIllu
Page 142 and 143:
LNC-MILLG87 Back Boring/CuttingM03
Page 144 and 145:
LNC-MILLG87 Back Boring/CuttingM03
Page 146 and 147:
LNC-MILLG88 Boring CycleG88 Boring
Page 148 and 149:
LNC-MILLG88 Boring CycleProgram Sam
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
LNC-MILLG89 Reaming CycleG89 Reamin
Page 156 and 157:
LNC-MILLG89 Reaming CycleProgram Sa
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
LNC-MILLG90, G91 Absolute, Incremen
Page 164 and 165:
LNC-MILLG92 Coordinate SettingBNew
Page 166 and 167:
LNC-MILLG98, G99 Retraction Point S
Page 168 and 169:
LNC-MILLG101~G105 Compound G-Code f
Page 170 and 171:
LNC-MILLG101 Linear Mode Multi-hole
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
LNC-MILLG102 Circular Mode of Multi
Page 178 and 179:
OLNC-MILLG102 Circular Mode of Mult
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
LNC-MILLG103 Arc Mode of Multi-hole
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
LNC-MILLG104 Grid Mode of Multi-hol
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
LNC-MILLG105 Promiscuous Mode of Mu
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
LNC-MILLG111 X-axis Two-Way Plane M
Page 208 and 209:
LNC-MILLG112 Two-way Plane Processi
Page 210 and 211:
LNC-MILLG113 One-way Plane Manufact
Page 212 and 213:
LNC-MILLG114 Y One-way Plane Manufa
Page 214 and 215:
Page 216 and 217:
LNC-MILLG122 Rectangle Shape Side M
Page 218 and 219:
Page 220 and 221:
LNC-MILLG132 Rectangle Shape Fillet
Page 223 and 224:
LNC MILLIndication of Auxiliary Fun
Page 225:
LNC MILLIndication of Auxiliary Fun
Page 228 and 229:
LNC MILLMACRO Program5.2 Macro Prog
Page 230 and 231:
LNC MILLMACRO Program5.2.4 Calling
Page 232 and 233:
LNC MILLMACRO Program5.2.5 Calling
Page 234 and 235:
LNC MILLMACRO Program5.4 MACRO Func
Page 236 and 237:
LNC MILLMACRO Program5.5.2 Classifi
Page 238 and 239:
LNC MILLMACRO Program7. Coordinate
Page 240 and 241:
LNC MILLMACRO ProgramTimesInstructi
Page 242 and 243:
LNC MILLMACRO Program5.5.4 Tool Com
Page 244 and 245:
LNC MILLMACRO Program5.5.7 Instruct
Page 246 and 247:
LNC MILLMACRO Program5.8 Compare Co
Page 248 and 249:
LNC MILLMACRO Program5.10 Flow Cont
Page 250 and 251:
LNC MILLMACRO Program• DO cycle c
Page 252:
LNC MILLMACRO Program#i=FIX(#j)(unc
show all

Programming Manual

Create successful ePaper yourself

Delete template?

Save as template?