Programming Manual

More documents

Recommendations

Info

LNC-MILLG30 Auto Return to the 2nd, 3rd and 4th Reference PointsG30 Auto Return to the 2nd, 3rd and 4th Reference PointsCommand FormatArgument InstructionAction Instruction⎡ 2⎤G30 P⎢3⎥⎢ ⎥< Axis >< Center point Location > ;⎢⎣4⎥⎦• P__Specify the reference point. Setting range: 2~4, corresponding to the 2nd~4 threference points.• AxisSpecify the name of axis being reverted to the reference points. It can be anycombination of X, Y, Z, A, B, C or U, V, W. The only condition is that it must beconsistent with the setting of current axis (the 4 th axis is set by using theparameter #0122). On the six-axes model M600, parameters #0288 & #0289are used to control the 5 th & 6 th axes.• Center point LocationCoordinate of the center point can be an absolute value or incrementalal valuein accordance with the status of G90 or G91.This command is used to return to 2 nd , 3 rd , 4 th reference points, and the tool willrevert to 2 nd , 3 rd , 4 th reference points through the center point from the currentposition.The offset of 2 nd reference point and the machine origin can be set by usingparameters #1022~1025; the offset of 3 rd reference point and the machine origincan be set by using parameters #1026~1029; and the offset of 4th reference pointand the machine origin can be set by using parameters #1030~1033.Before executing G30, the “manually return to origin” procedure must beexecuted at first, otherwise the system alarm will be triggered【MOT 4018:Returning to origin is not yet executed after boot】.When the argument X___ is not specified, return to origin will not be executed onX-axis; so will be it on other axes as well. If no argument of any axis is specified,the “Return to reference point” procedure will be executed at all axes.Note that the previously specified Tool Compensation value will be cancelledautomatically after G30 is executed.28 LNC Technology Co., Ltd.
LNC-MILLG30 Auto Return to the 2nd, 3rd and 4th Reference PointsIllustrationG90 G30 P2 X100. Y80.;G91 G30 P2 X0. Y0.;(NO center point)YSecond Reference PointYSecond Reference Point(50,50)(100,80)(50,50)XXLNC Technology Co., Ltd. 29
Page 3 and 4: LNC-MILLTable of ContentTable of Co
Page 5: LNC-MILLTable of ContentG131 Circul
Page 9: LNC-MILLG-Code Function TableG Code
Page 12 and 13: LNC-MILLG00 Rapid Positioning3 Comm
Page 14 and 15: LNC-MILLG01 Linear InterpolationG01
Page 16 and 17: LNC-MILLG02, G03 Circular/Helical I
Page 18 and 19: LNC-MILLG04 DwellG04 DwellCommand F
Page 20 and 21: LNC-MILLG10 Data Input SettingG10 D
Page 22 and 23: LNC-MILLG15 Polar Coordinate Comman
Page 24 and 25: LNC-MILLG17, G18, G19 Cutting Plane
Page 26 and 27: LNC-MILLG22, G23 Tool Stored Stroke
Page 28 and 29: LNC-MILLG27 Return to Origin CheckG
Page 30 and 31: LNC-MILLG28 Return to the First Ref
Page 32 and 33: LNC-MILLG29 Return from the First R
Page 36 and 37: LNC-MILLG31 Skip Signal Abort Block
Page 38 and 39: LNC-MILLG31 Skip Signal Abort Block
Page 40 and 41: LNC-MILLG41, G42 Tool Radius Compen
Page 42 and 43: LNC-MILLG43, G44, G49 Tool Length C
Page 44 and 45: LNC-MILLG43, G44, G49 Tool Length C
Page 46 and 47: LNC-MILLG50, G51 Scaling CommandIll
Page 48 and 49: LNC-MILLG52 Interval Coordinate Sys
Page 50 and 51: LNC-MILLG54~G59 Manufacturing Coord
Page 52 and 53: LNC-MILLG61, G64 Exact Positioning
Page 54 and 55: LNC-MILLG65 Simple CallO0001;..#1==
Page 56 and 57: LNC-MILLG66 Macro Program Mode Call
Page 58 and 59: LNC-MILLG67 Macro Program Mode Call
Page 60 and 61: 60°LNC-MILLG68, G69 Coordinate Sys
Page 62 and 63: LNC-MILLG73 Rapid Peck Drilling Cyc
Page 72 and 73: LNC-MILLG74 Left-Handed Screw Threa
Page 80 and 81: LNC-MILLG76 Fine Boring CycleG76 Fi
Page 82 and 83: LNC-MILLG76 Fine Boring CycleIllust
Page 84 and 85:
LNC-MILLG76 Fine Boring CycleM03 S1
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
LNC-MILLG81 Drilling CycleG81 Drill
Page 92 and 93:
LNC-MILLG81 Drilling CycleProgram S
Page 94 and 95:
LNC-MILLG81 Drilling CycleM03 S1000
Page 96 and 97:
Page 98 and 99:
LNC-MILLG82 Drilling CycleG82 Drill
Page 100 and 101:
LNC-MILLG82 Drilling CycleProgram S
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
LNC-MILLG83 Peck Drilling CycleG83
Page 108 and 109:
LNC-MILLG83 Peck Drilling CycleProg
Page 110 and 111:
LNC-MILLG83 Peck Drilling CycleM03
Page 112 and 113:
LNC-MILLG83 Peck Drilling CycleM03
Page 114 and 115:
LNC-MILLG84 Right-Handed Screw Thre
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
LNC-MILLG85 Reaming CycleG85 Reamin
Page 124 and 125:
LNC-MILLG85 Reaming CycleProgram Sa
Page 126 and 127:
LNC-MILLG85 Reaming CycleM03 S1000;
Page 128 and 129:
Page 130 and 131:
LNC-MILLG86 Boring CycleG86 Boring
Page 132 and 133:
LNC-MILLG86 Boring CycleProgram Sam
Page 134 and 135:
LNC-MILLG86 Boring CycleM03 S1000;G
Page 136 and 137:
Page 138 and 139:
LNC-MILLG87 Back Boring/CuttingG87
Page 140 and 141:
LNC-MILLG87 Back Boring/CuttingIllu
Page 142 and 143:
LNC-MILLG87 Back Boring/CuttingM03
Page 144 and 145:
LNC-MILLG87 Back Boring/CuttingM03
Page 146 and 147:
LNC-MILLG88 Boring CycleG88 Boring
Page 148 and 149:
LNC-MILLG88 Boring CycleProgram Sam
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
LNC-MILLG89 Reaming CycleG89 Reamin
Page 156 and 157:
LNC-MILLG89 Reaming CycleProgram Sa
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
LNC-MILLG90, G91 Absolute, Incremen
Page 164 and 165:
LNC-MILLG92 Coordinate SettingBNew
Page 166 and 167:
LNC-MILLG98, G99 Retraction Point S
Page 168 and 169:
LNC-MILLG101~G105 Compound G-Code f
Page 170 and 171:
LNC-MILLG101 Linear Mode Multi-hole
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
LNC-MILLG102 Circular Mode of Multi
Page 178 and 179:
OLNC-MILLG102 Circular Mode of Mult
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
LNC-MILLG103 Arc Mode of Multi-hole
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
LNC-MILLG104 Grid Mode of Multi-hol
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
LNC-MILLG105 Promiscuous Mode of Mu
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
LNC-MILLG111 X-axis Two-Way Plane M
Page 208 and 209:
LNC-MILLG112 Two-way Plane Processi
Page 210 and 211:
LNC-MILLG113 One-way Plane Manufact
Page 212 and 213:
LNC-MILLG114 Y One-way Plane Manufa
Page 214 and 215:
Page 216 and 217:
LNC-MILLG122 Rectangle Shape Side M
Page 218 and 219:
Page 220 and 221:
LNC-MILLG132 Rectangle Shape Fillet
Page 223 and 224:
LNC MILLIndication of Auxiliary Fun
Page 225:
LNC MILLIndication of Auxiliary Fun
Page 228 and 229:
LNC MILLMACRO Program5.2 Macro Prog
Page 230 and 231:
LNC MILLMACRO Program5.2.4 Calling
Page 232 and 233:
LNC MILLMACRO Program5.2.5 Calling
Page 234 and 235:
LNC MILLMACRO Program5.4 MACRO Func
Page 236 and 237:
LNC MILLMACRO Program5.5.2 Classifi
Page 238 and 239:
LNC MILLMACRO Program7. Coordinate
Page 240 and 241:
LNC MILLMACRO ProgramTimesInstructi
Page 242 and 243:
LNC MILLMACRO Program5.5.4 Tool Com
Page 244 and 245:
LNC MILLMACRO Program5.5.7 Instruct
Page 246 and 247:
LNC MILLMACRO Program5.8 Compare Co
Page 248 and 249:
LNC MILLMACRO Program5.10 Flow Cont
Page 250 and 251:
LNC MILLMACRO Program• DO cycle c
Page 252:
LNC MILLMACRO Program#i=FIX(#j)(unc
show all

Programming Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?