Programming Manual

More documents

Recommendations

Info

LNC-MILLG76 Fine Boring CycleM03 S1000;G17 G90 G00 G54 X0. Y0.;G00 Z100.;G98 G76 X0. Y0. Z-20. R10. P1000 Q5. K1 F100.; ---------------------------------------------------- (1)X-10. Z-30.; ------------------------------------------------------------------------------------------------------- (2)X20. Z-40.;------------------------------------------------------------------------------------------------------ (3)G80 G91 G28 X0. Y0. Z0.;M05;10 20+Y+X(2)(1)(3)Starting point(Cutter Retraction Point)+ZR point4010100+X2030(2) (1)(3)82 LNC Technology Co., Ltd.
LNC-MILLG80 Fixed Canned Cycle Cutting Mode CancelG80 Fixed Canned Cycle Cutting Mode CancelCommand FormatG80;Argument InstructionThis command is to cancel the fixed canned cycle cutting mode of G73, G74, G76,G81~G89.Besides G80, movement commands G00, G01, G02 and G03 can also be usedto cancel fixed canned cycle cutting mode.Program SampleG17 G90 G00 G54 X0. Y0.;Z100.;G99 G73 X0. Y0. Z-20. R10. Q4. K1 F100.;G80; ------------------------------------------------------------------------------------------- (G73 cycle cancel)G17 G90 G00 G54 X0. Y0.;Z100.;G99 G73 X0. Y0. Z-20. R10. Q4. K1 F100.;G00 Z100.;----------------------------------------------------------------------------------- (G73 cycle cancel)LNC Technology Co., Ltd. 83
Page 3 and 4:
LNC-MILLTable of ContentTable of Co
Page 5:
LNC-MILLTable of ContentG131 Circul
Page 9:
LNC-MILLG-Code Function TableG Code
Page 12 and 13:
LNC-MILLG00 Rapid Positioning3 Comm
Page 14 and 15:
LNC-MILLG01 Linear InterpolationG01
Page 16 and 17:
LNC-MILLG02, G03 Circular/Helical I
Page 18 and 19:
LNC-MILLG04 DwellG04 DwellCommand F
Page 20 and 21:
LNC-MILLG10 Data Input SettingG10 D
Page 22 and 23:
LNC-MILLG15 Polar Coordinate Comman
Page 24 and 25:
LNC-MILLG17, G18, G19 Cutting Plane
Page 26 and 27:
LNC-MILLG22, G23 Tool Stored Stroke
Page 28 and 29:
LNC-MILLG27 Return to Origin CheckG
Page 30 and 31:
LNC-MILLG28 Return to the First Ref
Page 32 and 33:
LNC-MILLG29 Return from the First R
Page 34 and 35:
LNC-MILLG30 Auto Return to the 2nd,
Page 36 and 37:
LNC-MILLG31 Skip Signal Abort Block
Page 38 and 39: LNC-MILLG31 Skip Signal Abort Block
Page 40 and 41: LNC-MILLG41, G42 Tool Radius Compen
Page 42 and 43: LNC-MILLG43, G44, G49 Tool Length C
Page 44 and 45: LNC-MILLG43, G44, G49 Tool Length C
Page 46 and 47: LNC-MILLG50, G51 Scaling CommandIll
Page 48 and 49: LNC-MILLG52 Interval Coordinate Sys
Page 50 and 51: LNC-MILLG54~G59 Manufacturing Coord
Page 52 and 53: LNC-MILLG61, G64 Exact Positioning
Page 54 and 55: LNC-MILLG65 Simple CallO0001;..#1==
Page 56 and 57: LNC-MILLG66 Macro Program Mode Call
Page 58 and 59: LNC-MILLG67 Macro Program Mode Call
Page 60 and 61: 60°LNC-MILLG68, G69 Coordinate Sys
Page 62 and 63: LNC-MILLG73 Rapid Peck Drilling Cyc
Page 72 and 73: LNC-MILLG74 Left-Handed Screw Threa
Page 80 and 81: LNC-MILLG76 Fine Boring CycleG76 Fi
Page 82 and 83: LNC-MILLG76 Fine Boring CycleIllust
Page 84 and 85: LNC-MILLG76 Fine Boring CycleM03 S1
Page 86 and 87: LNC-MILLG76 Fine Boring CycleM03 S1
Page 90 and 91: LNC-MILLG81 Drilling CycleG81 Drill
Page 92 and 93: LNC-MILLG81 Drilling CycleProgram S
Page 94 and 95: LNC-MILLG81 Drilling CycleM03 S1000
Page 98 and 99: LNC-MILLG82 Drilling CycleG82 Drill
Page 100 and 101: LNC-MILLG82 Drilling CycleProgram S
Page 106 and 107: LNC-MILLG83 Peck Drilling CycleG83
Page 108 and 109: LNC-MILLG83 Peck Drilling CycleProg
Page 110 and 111: LNC-MILLG83 Peck Drilling CycleM03
Page 112 and 113: LNC-MILLG83 Peck Drilling CycleM03
Page 114 and 115: LNC-MILLG84 Right-Handed Screw Thre
Page 122 and 123: LNC-MILLG85 Reaming CycleG85 Reamin
Page 124 and 125: LNC-MILLG85 Reaming CycleProgram Sa
Page 126 and 127: LNC-MILLG85 Reaming CycleM03 S1000;
Page 128 and 129: LNC-MILLG85 Reaming CycleM03 S1000;
Page 130 and 131: LNC-MILLG86 Boring CycleG86 Boring
Page 132 and 133: LNC-MILLG86 Boring CycleProgram Sam
Page 134 and 135: LNC-MILLG86 Boring CycleM03 S1000;G
Page 136 and 137: LNC-MILLG86 Boring CycleM03 S1000;G
Page 138 and 139:
LNC-MILLG87 Back Boring/CuttingG87
Page 140 and 141:
LNC-MILLG87 Back Boring/CuttingIllu
Page 142 and 143:
LNC-MILLG87 Back Boring/CuttingM03
Page 144 and 145:
LNC-MILLG87 Back Boring/CuttingM03
Page 146 and 147:
LNC-MILLG88 Boring CycleG88 Boring
Page 148 and 149:
LNC-MILLG88 Boring CycleProgram Sam
Page 150 and 151:
LNC-MILLG88 Boring CycleM03 S1000;G
Page 152 and 153:
LNC-MILLG88 Boring CycleM03 S1000;G
Page 154 and 155:
LNC-MILLG89 Reaming CycleG89 Reamin
Page 156 and 157:
LNC-MILLG89 Reaming CycleProgram Sa
Page 158 and 159:
LNC-MILLG89 Reaming CycleM03 S1000;
Page 160 and 161:
LNC-MILLG89 Reaming CycleM03 S1000;
Page 162 and 163:
LNC-MILLG90, G91 Absolute, Incremen
Page 164 and 165:
LNC-MILLG92 Coordinate SettingBNew
Page 166 and 167:
LNC-MILLG98, G99 Retraction Point S
Page 168 and 169:
LNC-MILLG101~G105 Compound G-Code f
Page 170 and 171:
LNC-MILLG101 Linear Mode Multi-hole
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
LNC-MILLG102 Circular Mode of Multi
Page 178 and 179:
OLNC-MILLG102 Circular Mode of Mult
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
LNC-MILLG103 Arc Mode of Multi-hole
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
LNC-MILLG104 Grid Mode of Multi-hol
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
LNC-MILLG105 Promiscuous Mode of Mu
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
LNC-MILLG111 X-axis Two-Way Plane M
Page 208 and 209:
LNC-MILLG112 Two-way Plane Processi
Page 210 and 211:
LNC-MILLG113 One-way Plane Manufact
Page 212 and 213:
LNC-MILLG114 Y One-way Plane Manufa
Page 214 and 215:
Page 216 and 217:
LNC-MILLG122 Rectangle Shape Side M
Page 218 and 219:
Page 220 and 221:
LNC-MILLG132 Rectangle Shape Fillet
Page 223 and 224:
LNC MILLIndication of Auxiliary Fun
Page 225:
LNC MILLIndication of Auxiliary Fun
Page 228 and 229:
LNC MILLMACRO Program5.2 Macro Prog
Page 230 and 231:
LNC MILLMACRO Program5.2.4 Calling
Page 232 and 233:
LNC MILLMACRO Program5.2.5 Calling
Page 234 and 235:
LNC MILLMACRO Program5.4 MACRO Func
Page 236 and 237:
LNC MILLMACRO Program5.5.2 Classifi
Page 238 and 239:
LNC MILLMACRO Program7. Coordinate
Page 240 and 241:
LNC MILLMACRO ProgramTimesInstructi
Page 242 and 243:
LNC MILLMACRO Program5.5.4 Tool Com
Page 244 and 245:
LNC MILLMACRO Program5.5.7 Instruct
Page 246 and 247:
LNC MILLMACRO Program5.8 Compare Co
Page 248 and 249:
LNC MILLMACRO Program5.10 Flow Cont
Page 250 and 251:
LNC MILLMACRO Program• DO cycle c
Page 252:
LNC MILLMACRO Program#i=FIX(#j)(unc
show all

Programming Manual

Create successful ePaper yourself

Delete template?

Save as template?