E - VAE ProSys sro

More documents

Recommendations

Info

$\ATS\schemi\ATS con S3-S4-S5\Rm002101.dwg - VAE ProSys sro$

3.3 Instructions for Mounting and InstallationRemove the terminal from the packaging. Items supplied are:− the MT− mounting elements• two for MT-40 and MT-45• four for MT-30• six for MT-60• eight for MT-91 and MT-120− this manual where applicableFitting can be directly into− cabinet doors or− operating panels.Selection of fitting position according to:− optimal height for operator− good lighting, so that the display is easy to read− suitable ventilation to be used in case of high ambient temperatures.− Avoid mounting in the immediate vicinity of switchgear or power converters.Prepare an opening with the following dimensions:Device Width Height Fitting depth Thickness/materialMT-30 138 +1 mm 106 + 1 mm 105 mm approx. max. 18 mmMT-40, MT-45 138 +1 mm 138 + 1 mm 125 mm approx. up to 40 mmMT-60283 ± 0.5 mm 139 ± 0.5 mm 110 mm approx. max. 18 mmConst. variation IMT-60283 ± 0.5 mm 79 + 0.5 mm 110 mm approx. max. 18 mmConst. variation II+ 3 holes(see diagram)MT-91 300 mm 180 mm 130 mm approx. max. 10 mmMT-121 300 ± 0.5 mm 180 ± 0.5 mm 120 mm approx. max. 8 mmExchange the labelling strip before the installation:The labelling stripes are to be changed at the rear of the device.• Pull out paper-tapes carefully with a tweezers. Do not press into the slot with a sharp tool because the front foilwill be damaged!• Inscribe the paper-tapes• Carefully insert again (at an angle of approx. 45 degrees):• in doing this, do not apply any pressure on the front panel• angling the corners simplifies insertionIf you produce new stripes, these must correspond in size to the original stripes (see appendix, "Labelling strips").They may not protrude over the rubber seal.E24Process display and control/ Device Manual/ Issue: 07.01
Fit the device using the mounting elements:− Fix the clamps at even distances in the gaps of the casing.Optimal spacing:• MT-30, MT-40, MT-45 one mounting element per side• MT-60, MT-91, MT-121 three mounting elements to the upper and lower sidesas well as one mounting element to each of the sidesthemselves.− Finger tighten the screws.− Check the position of the display, and take special care to check the correct seat of the sealing rubber.− Now tighten the clamping screws with a torque of 60N/cm.Caution:IP 65 (or IP 54 for MT-40 and MT-45) will be achieved by• quality installation and fitting• use of a flat and smooth mounting surface (after the clamping screws have been tightened)• the specified torque setting.Process display and control/ Device Manual/ Issue: 07.0125E
Page 2 and 3: RegulationsConcerning the Setting u
Page 4 and 5: 3.4 Overview of connection assignme
Page 6 and 7: 6.1.4 Address declaration Modbus-Ma
Page 8 and 9: 1 Product Overview1.1 Product range
Page 10 and 11: 1.3 Overview machine terminals with
Page 12 and 13: 1.4.4 RecordingThe devices contain
Page 14 and 15: 1.5 Software concept of graphic ter
Page 16 and 17: The following barcode readers have
Page 18 and 19: 2.3.3 Format for Modbus RTUGenerall
Page 20 and 21: 3 Mounting Instructions and Install
Page 22 and 23: 3.2.1 Shielding cables / leadsShiel
Page 26 and 27: 3.3.1 Mounting Diagram MT-60Constru
Page 28 and 29: 3.3.4 Mounting Diagram MT-91Dimensi
Page 30 and 31: Back wall MT-60Back wall MT-91 / MT
Page 32 and 33: Connections:Identification Signific
Page 34 and 35: Connection between the ends of the
Page 36 and 37: 3.5.5 Technical data of the ARCNET
Page 38 and 39: 3.7.1 PIN assignment for barcode in
Page 40 and 41: 4 Installation on the PLC4.1 Instal
Page 42 and 43: 4.2 Installation on the T200Standar
Page 44 and 45: Installation on X4The connection ca
Page 46 and 47: 4.3.2 Modbus RTU SlaveAC 31MK 92RS-
Page 48 and 49: 4.3.6 Connection via RS-485 on X2MT
Page 50 and 51: 4.3.9 Connection via RS-422 on X4MT
Page 53 and 54: 4.5 Connection to AC 41/ AC 51 with
Page 55 and 56: 4.7 Connection to KR / KT31 with Mo
Page 57 and 58: 4.8.3 Block 5F_ARC resp. 5F_ARC945F
Page 59: ArcNet reading procedure of the PLC
Page 63 and 64: 5.2 System download of MT-30Info:Al
Page 65 and 66: 5.5 Configuration during operation
Page 67 and 68: 5.5.5 Brightness control of the dis
Page 69 and 70: Adjustment of the baud rateIn the n
Page 71 and 72: 5.6 Starting-up and self test of MT
Page 73 and 74: 5.6.3 Basic MaskAfter error-free se
Page 75 and 76:
5.7.2 General settings5.7.2.1 Langu
Page 77 and 78:
5.7.2.5 Programming texts / systemD
Page 79 and 80:
Printer flow controlnoneXON/XOFF (s
Page 81 and 82:
5.7.2.8 Substation numberCaution:Th
Page 83 and 84:
5.7.2.14 Handling the fault listThe
Page 85 and 86:
5.7.4.3 Display testTest display?Ye
Page 87 and 88:
5.7.4.7 Test COM1Test COM1?YesNo -
Page 89 and 90:
5.8 Startup keys of MT-45, MT-91, M
Page 91 and 92:
6.1.1 Address declaration for CS316
Page 93 and 94:
6.1.2 Address declaration for T200
Page 95 and 96:
6.1.3 Address declaration for Modbu
Page 97 and 98:
6.1.4 Address declaration Modbus-Ma
Page 99 and 100:
6.1.5 Address declaration Modbus-Ma
Page 101 and 102:
6.2 Description of Functions / Over
Page 103 and 104:
How can a picture or text display b
Page 105 and 106:
+06 Bit Bit Bit Bit Bit Bit Bit Bit
Page 107 and 108:
+02 Bit Bit Bit Bit Bit Bit Bit Bit
Page 109 and 110:
Fault bit field 1-32 words for MT-4
Page 111 and 112:
6.4.3 Dynamic control wordBackgroun
Page 113 and 114:
Text number register (only MT-30, M
Page 115 and 116:
6.8 Any variables• Display resp.
Page 117 and 118:
6.8.2.2 Variables in SPSPlus WIN(pr
Page 119 and 120:
6.9 Text programming / special func
Page 121 and 122:
6.10.1 Global Parameterizing of rep
Page 123 and 124:
7 Operation7.1 General performance
Page 125 and 126:
Abbildung: MT-45Picture: MT-60Proce
Page 127 and 128:
7.2.1 Keyboard descriptionThe keybo
Page 129 and 130:
Functions in system menus (history,
Page 131 and 132:
Additional functions in edit menusK
Page 133 and 134:
Input of variablesThe input of vari
Page 135 and 136:
With MT-30:Type of variable Definit
Page 137 and 138:
7.5 Dynamic menu branchingBy means
Page 139 and 140:
7.5.2 Parameterizing of the returnT
Page 141 and 142:
7.6.3 Programming of a help textThe
Page 143 and 144:
7.7.2 Calling up the historyThe his
Page 145 and 146:
After the correct password has been
Page 147 and 148:
7.7.9 Exiting the historyThe functi
Page 149 and 150:
8 INDEX/ not into basic mask 109Ack
show all

E - VAE ProSys sro

Create successful ePaper yourself

Delete template?

Save as template?