General Index - National Roofing Contractors Association

Spray Polyurethane Foam-Based Systems; Protective Coatings -General InformationUNITED UNITED 1. COMPANY NAME UNITED UNITEDCOATINGS COATINGS COATINGS COATINGSELASTUFF ELASTUFF 2. PRODUCT NAME BERM UNISEAL101 102 600 EPOXYSEALER3A. COATING DESCRIPTIONAcrylilcXButylHypalonNeopreneSiliconeX X UrethaneVinylModified AsphaltOther (type)EPOXYNO NO 3B. VAPOR RETARDER (yes, perm rating 1.0) NO NOMEDIUM GRAY IVORY WHITE, 3C. COLORS AVAILABLE LIGHT GRAY, CLEAR, BLACKLIMITED CUSTOMTAN, CUSTOMSAME ELASTUFF 101 4. BASE COATING (Name of Product) BERM 500DIATHIONELASTUFF 102 SAME TOP COATING (Name of Product) BERM 6005. NUMBER OF COATING APPLICATIONS REQUIRED1 Base Coatings 11 Top Coatings 1NO OPTIONAL Granules Required (yes, no or optional) OPTIONAL6. REQUIRED DRY FILM THICKNESS: (mils)17 Base Coating 11 MIN. 1/2 – 2 MIN.7 Tom Coating 11 MIN.7. FILM CURE TIME6 – 8 HOURS Base Coating 1 1/2 – 2 HOURS 8 HOURS8 – 12 HOURS Top Coating 1 1/2 – 2 HOURS1/2" 1/2" 8. MINIMUM SLOPE REQUIRED (inches per foot) 1/2"9. REQUIREMENTS FOR USE OVER:(X=direct application permitted) (P=primer required)(T=thermal barrier required)P P Concrete Decks XP P Plywood Decks XP P Metal Decks PExisting Spudded Built-up RoofingXX X Other Coatings XSELF SELF 10. FLASHING MATERIAL (type or self-flashing) SELF SELF11. APPLICATION CONDITIONS40 – 110 40 – 110 Recommended Ambient Air Temperature Range (degrees F) 50 – 110 50 – 11012 12 Maximum Permitted Wind Velocity Without Screen (mph) 12 1220 20 Maximum Permitted Wind Velocity With Wind Screen (mph) 20 2012. APPLICATION EQUIPMENT REQUIREMENTSX X Single-Component Airless Spray X XMulti-Component Airless SprayX X Other (roller, brush, etc.) X XNONE NONE 13. RESTRICTED REGIONS (yes/none) NONE NONEYES YES 14. RESTRICTED BUILDING USES (yes/none) YES YES5 5 15. RECOMMENDED RECOATING SCHEDULE (years or none) 516. PHYSICAL PROPERTIES OF THE COATING1000 2500 Tensile Strength Per ASTM D 412 or Other (psi) 250500 400 Elongation Per ASTM D 412 or Other (%) 240Impact Resistance Per ASTM D 2794 or Other (inch lbs)NO CHANGE Accelerated Weathering Per ASTM D 882 or Other (color change) NO CHANGEHeat Aging Per ASTM D 573 or Other (%)1.0 MAX 2.5 MAX Water Absorption Per ASMT D 570 or Other (%)YES YES 17. UL 790 FLAMMABILITY CLASS A RATING IN ANY SYSTEM (yes/no) YES18. FOAM INSULATION REQUIREMENTS1 1 Minimum Thickness (inches) 12.5 – 3.0 2.5 – 3.0 Nominal Density Per ASTM D 1622 or Other (lbs/ft 3 ) 2.5 – 3.040 40 Compressive Strength Per ASTM D 1621 or Other (psi) 40 MIN.90 90 Closed Cell Content Per ASTM D 2856 or Other (%) 90 MIN.NO NO 19. FOAM AVAILABLE FROM MANUFACTURER (yes/no) NO1989 1989 20. YEAR OF FIRST COMMERCIAL USE 1990 19953,000 5,000 21. NUMBER OF SQUARES INSTALLED (100 ft 2 )NO NO 22. MANUFACTURER-QUALIFIED APPLICATOR REQUIRED (yes/no) NO NODISTRS, DIRECT DISTRS, DIRECT 23. METHODS OF DISTRIBUTION (distributors and/or direct) DISTRS, DIRECT DISTRS, DIRECT4 4 24. NUMBER OF REGIONAL SERVICE LOCATIONS 8 8B. MANN B. MANN 25. FOR SALES INFORMATION, CONTACT: B. MANN B. MANN800/541-4383 800/541-4383 800/541-4383 800/541-4383B. MANN B. MANN FOR TECHNICAL INFORMATION, CONTACT: B. MANN B. MANN800/541-4383 800/541-4383 800/541-4383 800/541-438326. SEE APPENDIX IF CHECKEDNA=not applicable275