hybrid operation, maintenance and warranty manual - Steyr Motors

More documents

Recommendations

Info

3 442651023 854512060200,511,5255 3 4 426510902500CLEAN EFFICIENT POWER25020501003 85 4 85550 120 6 1201. To start the Hybrid- engine in D-MODE, move throttle lever into idle position and gear into neutral position.2. Press the push button for ignition (ill.F;red) (push button lock in place);An audible alarm will sound (for 0,7sec.) and the warning lights are illuminated (temporary), indicating the correctfunction of the audible and visual warning system.STARTONOFF11-041NOTE:In case of a low temperature start, wait until the combined oil pressure/glow plug preheating indication light isturned off, then continue with the start procedure.3.Wait till SCC has completely started up showing below screen- menu “Main”STEYR-CONTROL-CENTER49.16.45N 48.08.56N 102.41.11W 014.27.47W 57,4 117 14:05 22:57HCUHCUSPEED/KN10.0 3412 3rpm x 10004RPM2650 1500MAIN05SWITCH2103 4 43 85 46bar 52 °C 568 1502,8 6.377.8 73OIL/BARTEMP/°C120 611-0344.Select on SCC menu “HCU” to enter below shown screen.STEYR-CONTROL-CENTER49.16.45N 48.08.56N 014.27.47W 102.41.11W 57,4 117 14:0522:57SPEED/KN10.0 34012 3rpm x 100045bar °C86 1502,8 6.377.8 73OIL/BARTEMP/°CRPM2650 1500HCUMAINSWITCHSTEYR-CONTROL-CENTERR49.16.45N 48.08.56N 102.41.11W 014.27.47W 57,4 117 14:05 22:57GENER.SPEED/KN10.0 34rpm12 3rpm x 1000A9870 131E-Speed HCU/CURHybrid statustus45RPM MAIN2650 1500E-Mode ready°C bar D-Mode ready °C °C68 HCU ok150HCU2,8 6.377.8 E-MOTOR 73OIL/BARTEMP/°CV48,00BATTERYSWITCHGENER.Hybrid statusE-Mode readyD-Mode readyHCU ok11-03211-013- 20 -Z001045-0_1_March 2012
Check following parameters on screen „HCU” before continuing with start- procedure:- E-Mode ready= red illustrated,- D-Mode ready= green illustrated,- HCU o.k.=green illustrated- GENER.= green illustrated,- BATTERY= between min.45V/max.57V .NOTE: If parameters are not displayed as described above, follow chapter chapter 4.TROUBLE SHOOTINGor contact your authorized STEYR MOTORS marine DEALER.5. Press the button START (ill.G; green) and hold in this position until "starting" of engine, but under nocircumstances hold in this position for more than ten seconds.If engine does not start, release start – push button momentarily and repeat starting procedure.ATTENTION: If Hybrid- engine is not to start, in emergency cases conventional startermotor can beused for start- up. To start the Hybrid- engine with conventional startermotor refer to chapter 2.5(STEYR MOTORS recommends to use conventional startermotor only in emergency- cases. If conventionalstarter-motor is used, contact authorized STEYR MOTORS DEALER for fault investigation as soon as possible)6. As soon as engine starts, release start button. The audible alarm will stop when normal oil pressure hasbeen reached.ATTENTION: If engine fails to start within one minute and/or repeated attempts, try to start in emergency caseswith conventional startermotor (proceed according chapter 2.5) or contact your STEYR MOTORS Marine dealer.Never push start button when engine is running.STOPPING HYBRID ENGINE in D-MODE (for SOLAS only)1. Move throttle lever into idle position and gear in neutral position.2. Cool down the engine.3. Press push button ignition ON/OFF (ill.F) to disengage from locking position and to shut OFF the engine.ATTENTION:Do not stop engine at speeds above idle or accelerate engine while turning off ignition. This may result inengine failures.Z001045-0_1_March 2012 - 21 -
Page 1 and 2: HYBRIDOPERATION, MAINTENANCEAND WAR
Page 3 and 4: WELCOME ABOARDCongratulations on yo
Page 5 and 6: TABLE OF CONTENTS1. GENERAL PART ..
Page 7 and 8: 1.2. Product References, Illustrati
Page 11 and 12: 1.15. SymbolsCertain symbols or com
Page 13 and 14: CLEAN EFFICIENT POWERCLEAN EFFICIEN
Page 15 and 16: 2.3 Starting/Stopping a Hybrid Engi
Page 17 and 18: Check following parameters on scree
Page 19: *) Starting/Stopping the Hybrid- En
Page 23 and 24: 3 442651023 854512060200,51551,5290
Page 25 and 26: CLEAN EFFICIENT POWER6. To start E-
Page 27 and 28: CLEAN EFFICIENT POWER1. Move thrott
Page 29 and 30: *) Starting/Stopping the Hybrid- En
Page 31 and 32: CLEAN EFFICIENT POWERCheck followin
Page 33 and 34: CLEAN EFFICIENT POWERSTOPPING HYBRI
Page 35 and 36: CLEAN EFFICIENT POWERVARIANT B:1. P
Page 37 and 38: CLEAN EFFICIENT POWER1.To start the
Page 39 and 40: 3 4 43 85 4265251068 150120 6SWITCH
Page 41 and 42: E-ModeManualDrive12 VStartE-ModeMan
Page 43 and 44: CLEAN EFFICIENT POWERNOTE:In case o
Page 45 and 46: 2.10 Gear Box - InformationNOTE: Yo
Page 47 and 48: CLEAN EFFICIENT POWER2. Ignition ON
Page 49 and 50: CLEAN EFFICIENT POWER• in E-Mode
Page 51 and 52: Instrument PanelHybrid Engines are
Page 53 and 54: • HCU is limiting or stopping cha
Page 55 and 56: CLEAN EFFICIENT POWERMain Switch to
Page 57 and 58: If temperature-values exceed from S
Page 59 and 60: 2.17 Diagnostic systemThe electroni
Page 61 and 62: 2.19 Economy in Electrical-MODE (E-
Page 63 and 64: THIS PAGE IS INTENTIONALLY BLANKZ00
Page 65 and 66: Z001045-0_1_March 2012 - 65 -4.2 Tr
Page 67 and 68: Z001045-0_1_March 2012 - 67 -
Page 69 and 70: 4.3. Reading Service Codes/Alarms f
Page 71 and 72:
CODE ABBREV. 150 PINWIREChart -Serv
Page 73 and 74:
5.2. Preparation for Off Season Sto
Page 75 and 76:
THIS PAGE IS INTENTIONALLY BLANKZ00
Page 77:
SERVICENETWORKAUSTRIASTEYR MOTORS G
show all

hybrid operation, maintenance and warranty manual - Steyr Motors

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?