PNEG-1156ETL - David Manufacturing Co.

More documents

Recommendations

Info

4. Assembly and Installationc. Use the hole in the track as a guide to drill or punch the next hole and install an additional trackbracket and bolt; repeat this process around the bin. Tighten bolts as you go. (See Figure 4E.)Figure 4ENOTE: If upon completing the circuit of the bin, the last section needed is less than 3' in length,shorten the preceding piece so that a 3' or longer section can be used as the final section.There should be slightly more material than required.3. The end of the last section should be cut to fit snugly against the starting end of the first length anda 5/16" hole drilled about 5/8" from the cut off end. All track joints should be aligned as smoothlyas possible.The closer the augers run to the bin wall, the less chance of grain spoilage. Drying in cold weathercan require the use of wall liners (not sold by GSI) or air tubes (sold separately) to minimize binwall spoilage.NOTE: After the wall track is installed, check clearance between the track and bin sheet splice bolts.Long bolts may catch on the Stir-Ator track wheel or pivot pin on the track unit. To alleviatethis problem, cut off the bolts or reverse them.22 PNEG-1156ETL Design III Series Grain Stir-Ator CSA
4. Assembly and InstallationSuspension Chains1. The bin roof is then assembled and the suspension chains are dropped through the fill-hole. Two (2)chains are used on the single and double auger units and three (3) chains are used on thetriple auger units. Space the suspension hooks equally apart around the center fill-hole collar,placing them in reference to the manhole where the shut off switch box is to be located. Place chainsthrough the hole and then slide the chain down into the slot. (See Figure 4F and Figure 4G.) A holein the suspension hooks is provided if bolting the hooks in position is desired. NOTE: For GSIbins larger than 33' diameter an alternate method of mounting is to attach suspension chainto intermediate center collar. (See Figure 4H on Page 24.)Figure 4F Viewed from top of binFigure 4GWARNINGDo not use the bolt in the suspension hook to support the entire unit. The outsideend of the Stir-Ator should be supported by the track.PNEG-1156ETL Design III Series Grain Stir-Ator CSA 23
Page 4 and 5: Table of ContentsChapter 9 Wiring D
Page 6 and 7: 1. SafetySafety InstructionsOur for
Page 9 and 10: 1. SafetyWear Protective ClothingWe
Page 11 and 12: 1. SafetyCAUTIONSAFETY FIRST PAYSRe
Page 13 and 14: 2. Safety DecalsThe decals shown be
Page 15 and 16: 3. Specifications and DimensionsDes
Page 17: 3. Specifications and DimensionsDes
Page 20 and 21: 4. Assembly and InstallationTrack I
Page 24 and 25: 4. Assembly and InstallationSwitch
Page 26 and 27: 4. Assembly and InstallationFrame R
Page 28 and 29: 4. Assembly and Installation2. For
Page 30 and 31: 4. Assembly and InstallationYokes1.
Page 32 and 33: 4. Assembly and Installation2. 36'
Page 34 and 35: 4. Assembly and Installation2. Afte
Page 36 and 37: 4. Assembly and InstallationCenter
Page 38 and 39: 4. Assembly and InstallationLifting
Page 40 and 41: 4. Assembly and Installation4. When
Page 42 and 43: 4. Assembly and Installation3. Use
Page 44 and 45: 4. Assembly and InstallationCheck M
Page 46 and 47: 4. Assembly and InstallationCutting
Page 48 and 49: 5. OperationStart-Up Procedure (Ful
Page 50 and 51: 5. OperationStir-Guard Option Insta
Page 52 and 53: 5. Operation**Number of Stir-Ator A
Page 54 and 55: NOTES54 PNEG-1156ETL Design III Ser
Page 56 and 57: 6. Parts ListDesign III Stir-Ator T
Page 58 and 59: 6. Parts ListDesign III Stir-Ator S
Page 60 and 61: 6. Parts ListDesign III Stir-Ator Y
Page 62 and 63: 6. Parts ListDesign III Stir-Ator Y
Page 64 and 65: 6. Parts ListDesign III Stir-Ator D
Page 70 and 71: 6. Parts ListDMC 440V - Gear Motor
Page 72 and 73:
6. Parts ListStir-Ator Guard Option
Page 74 and 75:
7. Service and MaintenanceTrolley D
Page 76 and 77:
7. Service and MaintenanceSafety Sh
Page 78 and 79:
8. TroubleshootingProblemProbable C
Page 80 and 81:
9. Wiring DiagramsDesign III Stir-A
Page 82 and 83:
9. Wiring DiagramsDesign III Stir-A
Page 84:
This equipment shall be installed i
show all

PNEG-1156ETL - David Manufacturing Co.

Create successful ePaper yourself

Delete template?

Save as template?