PNEG-1156ETL - David Manufacturing Co.

More documents

Recommendations

Info

4. Assembly and Installation2. After making electrical connections, replace cover screw. Secure electrical wires to wire support rodusing two (2) wire ties. Trim excess. (See Figure 4AA and Figure 4AB.)Figure 4AA Junction Box Wiring Diagram - 1 PhaseFigure 4AB Junction Box Wiring Diagram - 3 Phase34 PNEG-1156ETL Design III Series Grain Stir-Ator CSA
4. Assembly and InstallationTrolley Drive Arm to Cable1. Connect trolley drive arm to cable connector using one 1/4" SAE (Society of Automotive Engineersstandard) flat washer and 5/32" x 1" cotter pin. (See Figure 4AC and Figure 4AD.) Be sure cableconnector is as shown in Figure 4AD. If assembled incorrectly, connector will not go aroundcable pulleys.Figure 4ACFigure 4ADNOTICEBe sure the trolley drive arm points to the center of the bin.Double check that the trolley unit on the main frame has been installed correctly.PNEG-1156ETL Design III Series Grain Stir-Ator CSA 35
Page 4 and 5: Table of ContentsChapter 9 Wiring D
Page 6 and 7: 1. SafetySafety InstructionsOur for
Page 9 and 10: 1. SafetyWear Protective ClothingWe
Page 11 and 12: 1. SafetyCAUTIONSAFETY FIRST PAYSRe
Page 13 and 14: 2. Safety DecalsThe decals shown be
Page 15 and 16: 3. Specifications and DimensionsDes
Page 17: 3. Specifications and DimensionsDes
Page 20 and 21: 4. Assembly and InstallationTrack I
Page 22 and 23: 4. Assembly and Installationc. Use
Page 24 and 25: 4. Assembly and InstallationSwitch
Page 26 and 27: 4. Assembly and InstallationFrame R
Page 28 and 29: 4. Assembly and Installation2. For
Page 30 and 31: 4. Assembly and InstallationYokes1.
Page 32 and 33: 4. Assembly and Installation2. 36'
Page 36 and 37: 4. Assembly and InstallationCenter
Page 38 and 39: 4. Assembly and InstallationLifting
Page 40 and 41: 4. Assembly and Installation4. When
Page 42 and 43: 4. Assembly and Installation3. Use
Page 44 and 45: 4. Assembly and InstallationCheck M
Page 46 and 47: 4. Assembly and InstallationCutting
Page 48 and 49: 5. OperationStart-Up Procedure (Ful
Page 50 and 51: 5. OperationStir-Guard Option Insta
Page 52 and 53: 5. Operation**Number of Stir-Ator A
Page 54 and 55: NOTES54 PNEG-1156ETL Design III Ser
Page 56 and 57: 6. Parts ListDesign III Stir-Ator T
Page 58 and 59: 6. Parts ListDesign III Stir-Ator S
Page 60 and 61: 6. Parts ListDesign III Stir-Ator Y
Page 62 and 63: 6. Parts ListDesign III Stir-Ator Y
Page 64 and 65: 6. Parts ListDesign III Stir-Ator D
Page 70 and 71: 6. Parts ListDMC 440V - Gear Motor
Page 72 and 73: 6. Parts ListStir-Ator Guard Option
Page 74 and 75: 7. Service and MaintenanceTrolley D
Page 76 and 77: 7. Service and MaintenanceSafety Sh
Page 78 and 79: 8. TroubleshootingProblemProbable C
Page 80 and 81: 9. Wiring DiagramsDesign III Stir-A
Page 82 and 83: 9. Wiring DiagramsDesign III Stir-A
Page 84:
This equipment shall be installed i
show all

PNEG-1156ETL - David Manufacturing Co.

Create successful ePaper yourself

Delete template?

Save as template?