PNEG-1156ETL - David Manufacturing Co.

More documents

Recommendations

Info

4. Assembly and InstallationYokes1. The yoke assembly is attached to the frame rails by placing the pivot tube into the center framesupport. If the pivot tube does not slide in readily, file any burrs and grease the inside of the centerframe support. Secure by placing a 1/4" x 3" cotter pin through the tube. Open the end of the cotterpin. The end yoke is bolted to the left frame rail with two (2) 3/8" x 1" carriage bolts, lock washers andhex nuts. Bolt from the inside out. Tighten with socket head on impact wrench. (See Figure 4T, Figure4U below, Figure 4V and Figure 4W on Page 31.)Figure 4TFigure 4U30 PNEG-1156ETL Design III Series Grain Stir-Ator CSA
4. Assembly and InstallationFigure 4VFigure 4WPNEG-1156ETL Design III Series Grain Stir-Ator CSA 31
Page 4 and 5: Table of ContentsChapter 9 Wiring D
Page 6 and 7: 1. SafetySafety InstructionsOur for
Page 9 and 10: 1. SafetyWear Protective ClothingWe
Page 11 and 12: 1. SafetyCAUTIONSAFETY FIRST PAYSRe
Page 13 and 14: 2. Safety DecalsThe decals shown be
Page 15 and 16: 3. Specifications and DimensionsDes
Page 17: 3. Specifications and DimensionsDes
Page 20 and 21: 4. Assembly and InstallationTrack I
Page 22 and 23: 4. Assembly and Installationc. Use
Page 24 and 25: 4. Assembly and InstallationSwitch
Page 26 and 27: 4. Assembly and InstallationFrame R
Page 28 and 29: 4. Assembly and Installation2. For
Page 32 and 33: 4. Assembly and Installation2. 36'
Page 34 and 35: 4. Assembly and Installation2. Afte
Page 36 and 37: 4. Assembly and InstallationCenter
Page 38 and 39: 4. Assembly and InstallationLifting
Page 40 and 41: 4. Assembly and Installation4. When
Page 42 and 43: 4. Assembly and Installation3. Use
Page 44 and 45: 4. Assembly and InstallationCheck M
Page 46 and 47: 4. Assembly and InstallationCutting
Page 48 and 49: 5. OperationStart-Up Procedure (Ful
Page 50 and 51: 5. OperationStir-Guard Option Insta
Page 52 and 53: 5. Operation**Number of Stir-Ator A
Page 54 and 55: NOTES54 PNEG-1156ETL Design III Ser
Page 56 and 57: 6. Parts ListDesign III Stir-Ator T
Page 58 and 59: 6. Parts ListDesign III Stir-Ator S
Page 60 and 61: 6. Parts ListDesign III Stir-Ator Y
Page 62 and 63: 6. Parts ListDesign III Stir-Ator Y
Page 64 and 65: 6. Parts ListDesign III Stir-Ator D
Page 70 and 71: 6. Parts ListDMC 440V - Gear Motor
Page 72 and 73: 6. Parts ListStir-Ator Guard Option
Page 74 and 75: 7. Service and MaintenanceTrolley D
Page 76 and 77: 7. Service and MaintenanceSafety Sh
Page 78 and 79: 8. TroubleshootingProblemProbable C
Page 80 and 81:
9. Wiring DiagramsDesign III Stir-A
Page 82 and 83:
9. Wiring DiagramsDesign III Stir-A
Page 84:
This equipment shall be installed i
show all

PNEG-1156ETL - David Manufacturing Co.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?