PNEG-1156ETL - David Manufacturing Co.

More documents

Recommendations

Info

4. Assembly and Installation3. Use the shut off support chain(s) to hold the shut off chain so that there is adequate clearancebetween the shut off chain and the Stir-Ator as it travels underneath. (See Figure 4AQ.)Design III Stir-AtorFigure 4AQ4. Attach the chain to the handle extension by clipping it onto the bolt positioned on the end of thehandle extension. (See Figure 4AR.)Switch boxHandle extensionBoltChain clipFigure 4AR5. String the lead-in wire through the chain link clevis on the bottom of the suspension bar toward thebar with the safety chain “S” hook. (Do not attach the wire to the end of the suspension bar.)The lead-in wire can then be suspended above the safety chain and routed to the switch box.(See Figure 4AS on Page 43.)42 PNEG-1156ETL Design III Series Grain Stir-Ator CSA
4. Assembly and InstallationFigure 4ASWARNINGThe lead-in wire from the Stir-Ator to the switch box must be longer and looser thanthe shut off chain itself. Should the Stir-Ator malfunction and engage the shut off,this prevents the lead-in wire from being torn from the switch box which couldresult in serious electrical shock.Operating the Stir-Ator without the shut off chain properly assembled andinstalled could result in serious electrical shock or bodily injury and would voidthe warranty.See Pages 17, 23 and 24 for proper installation and clearance of the shut off chainand Stir-Ator.6. Hook wire support “S” hook to support chain approximately 12" above the shut off chain.(See Figure 4AT.)Design III Stir-AtorFigure 4AT7. After adjustments are completed, “S” hooks on the suspension chains and shut off chains shouldbe closed.PNEG-1156ETL Design III Series Grain Stir-Ator CSA 43
Page 4 and 5: Table of ContentsChapter 9 Wiring D
Page 6 and 7: 1. SafetySafety InstructionsOur for
Page 9 and 10: 1. SafetyWear Protective ClothingWe
Page 11 and 12: 1. SafetyCAUTIONSAFETY FIRST PAYSRe
Page 13 and 14: 2. Safety DecalsThe decals shown be
Page 15 and 16: 3. Specifications and DimensionsDes
Page 17: 3. Specifications and DimensionsDes
Page 20 and 21: 4. Assembly and InstallationTrack I
Page 22 and 23: 4. Assembly and Installationc. Use
Page 24 and 25: 4. Assembly and InstallationSwitch
Page 26 and 27: 4. Assembly and InstallationFrame R
Page 28 and 29: 4. Assembly and Installation2. For
Page 30 and 31: 4. Assembly and InstallationYokes1.
Page 32 and 33: 4. Assembly and Installation2. 36'
Page 34 and 35: 4. Assembly and Installation2. Afte
Page 36 and 37: 4. Assembly and InstallationCenter
Page 38 and 39: 4. Assembly and InstallationLifting
Page 40 and 41: 4. Assembly and Installation4. When
Page 44 and 45: 4. Assembly and InstallationCheck M
Page 46 and 47: 4. Assembly and InstallationCutting
Page 48 and 49: 5. OperationStart-Up Procedure (Ful
Page 50 and 51: 5. OperationStir-Guard Option Insta
Page 52 and 53: 5. Operation**Number of Stir-Ator A
Page 54 and 55: NOTES54 PNEG-1156ETL Design III Ser
Page 56 and 57: 6. Parts ListDesign III Stir-Ator T
Page 58 and 59: 6. Parts ListDesign III Stir-Ator S
Page 60 and 61: 6. Parts ListDesign III Stir-Ator Y
Page 62 and 63: 6. Parts ListDesign III Stir-Ator Y
Page 64 and 65: 6. Parts ListDesign III Stir-Ator D
Page 70 and 71: 6. Parts ListDMC 440V - Gear Motor
Page 72 and 73: 6. Parts ListStir-Ator Guard Option
Page 74 and 75: 7. Service and MaintenanceTrolley D
Page 76 and 77: 7. Service and MaintenanceSafety Sh
Page 78 and 79: 8. TroubleshootingProblemProbable C
Page 80 and 81: 9. Wiring DiagramsDesign III Stir-A
Page 82 and 83: 9. Wiring DiagramsDesign III Stir-A
Page 84: This equipment shall be installed i

PNEG-1156ETL - David Manufacturing Co.

Create successful ePaper yourself

Delete template?

Save as template?