Brisque to Lotem 800 II / Lotem Quantum Family - Kodak

More documents

Recommendations

Info

118 Chapter 5 – Proofing a Job on the Lotem 800 II / Lotem 800 II Quantum with Spectrum from the Brisque3. The components of the currently selected Donor Set are listed underDonor Set.The dimensions of the receiver of the currently selected Donor Set arelisted in Media Size.In Select Media, select the Donor Set with which you want to proof.The Donor Set and Media Size parameters update accordingly.
Defining the Lotem Spectrum Parameters 119Layout TabUse the Layout tab to set the proofing mode, and the alignment, offset,scale, and orientation of the proofed Job.1. In Alignment, select Top-Left or Top-Center to specify the startingpoint of exposure (see the illustration later).
Page 3:
Table of ContentsNotes & Informatio
Page 6:
The text and drawings herein are fo
Page 11 and 12:
Using This ManualWho Should Use Thi
Page 13 and 14:
Additional DocumentationxiAdditiona
Page 15:
Conventions Used in This Manualxiii
Page 18 and 19:
2 Chapter 1 - OverviewBrisque to Lo
Page 20 and 21:
4 Chapter 1 - OverviewIf during the
Page 22 and 23:
6 Chapter 1 - OverviewWhat is Lotem
Page 24 and 25:
8 Chapter 1 - OverviewWhat is Lotem
Page 27 and 28:
Configuring and Calibratingthe Lote
Page 29 and 30:
Accessing the Output Device Configu
Page 31 and 32:
Configuring the Lotem 800 II / Lote
Page 33 and 34:
Configuring the Lotem 800 II / Lote
Page 35 and 36:
Lotem 800 II / Lotem Quantum Plates
Page 37 and 38:
Lotem 800 II / Lotem Quantum Plates
Page 39 and 40:
Press Format 23Reset Screen Board i
Page 41 and 42:
Press Format 254. Define Margins: H
Page 43 and 44:
Excurve Calibration 273. Click Save
Page 45 and 46:
Excurve Calibration 29Making a Test
Page 47 and 48:
Excurve Calibration 31Creating the
Page 49 and 50:
Excurve Calibration 33Additional pa
Page 51 and 52:
Excurve Calibration 35Viewing an Ex
Page 53 and 54:
Excurve Calibration 375. Develop th
Page 55 and 56:
Excurve Calibration 39To define Aut
Page 57 and 58:
Excurve Calibration 41Optional Excu
Page 59 and 60:
Tone Reproduction 435. To select on
Page 61 and 62:
Tone Reproduction 458. Entering Ton
Page 63 and 64:
Tone Reproduction 476. Click OK; yo
Page 65 and 66:
Tone Reproduction 492. To display t
Page 67 and 68:
Screen Sets 51To configure the Maxi
Page 69 and 70:
Screen Sets 53Important: A screen s
Page 71 and 72:
Screen Sets 556. Click Done to retu
Page 73 and 74:
Screen Sets 57Adding User CommentsY
Page 75 and 76:
Screen Sets 59To define a Screen Fr
Page 77 and 78:
Screen Sets 613. Press ENTER. The n
Page 79:
Screen Sets 63Automatic Definitions
Page 83 and 84: Processing a Job on theLotem 800 II
Page 85 and 86: Overview 693. Define the Plate Expo
Page 87 and 88: Aligning Signature Elements 71Align
Page 89 and 90: Aligning Signature Elements 73Viewi
Page 91 and 92: Launching the Job to a Brisque Temp
Page 93 and 94: Launching the Job to a Brisque Temp
Page 95 and 96: Defining the Plate Expose Parameter
Page 101 and 102: Defining the Store Parameters 85Def
Page 103 and 104: Defining the Store Parameters 87•
Page 105 and 106: Submitting the Job Ticket for Proce
Page 107 and 108: Performing a Plate Remake 91To perf
Page 109 and 110: Performing a Plate Remake 936. Clic
Page 111: Sending the Job for Long Term Stora
Page 114 and 115: 98 Chapter 4 - Configuring and Cali
Page 116 and 117: 100 Chapter 4 - Configuring and Cal
Page 128 and 129: 112 Chapter 5 - Proofing a Job on t
Page 150 and 151: 134 Brisque to Lotem 800 II / Lotem
show all

Brisque to Lotem 800 II / Lotem Quantum Family - Kodak

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?