Brisque to Lotem 800 II / Lotem Quantum Family - Kodak

More documents

Recommendations

Info

4 Chapter 1 – OverviewIf during the login procedure, a process/application does not load properlyor a board is not detected, then a results window appears detailing thefaults. Click Continue Logon to continue the login procedure. However,you should report the problem to your system administrator.When the login is completed, the Brisque Launch Pad is displayed on theBrisque CDE (Common Desktop Environment).Note: The CDE opens in its last saved state. For example, the windows that wereopen when the CDE was saved will reappear after login.LogoutWe recommend that you logout from the system when you finish work, butstop short of actually switching off the computer.WARNING: If you need to switch the computer off, DO NOT switch it off untilyou complete both the logout and shutdown procedures.To logout from the system:1. From the Brisque Launch Pad, double-click Exit.2. Click Continue logout to continue the process. When the consolelogin prompt appears, you are logged out from the system.Or, to cancel the logout, click Cancel logout.Note: Do not switch off the computer until you perform the shutdownprocedure (see Shutdown on page 5).Alternative logout method:1. Right-click the Brisque desktop, or left/right click the Launch PadWindow Control box; a popup menu appears.2. Click the Log out option; the Logout Confirmation window appears.3. Click Continue logout to exit the system; when the console loginprompt appears, you are logged out from the system.Important: If the system freezes or does not respond during the logoutprocedure, you must reset the system (see What is Lotem 400 Quantum /Lotem 800 II / Lotem 800 II Quantum? on page 6).
Brisque Login, Logout and Shutdown 5ShutdownDo not turn the Brisque power switch off before properly logging out andshutting down the Brisque. Switching the power off without performingthe shutdown procedure may damage your data and system files.Note: You might want to perform shutdown as a routine maintenanceprocedure only whenever the system seems to be processing slowly. However, asa maintenance procedure, DO NOT shut down the system more than once aweek.To shut down the system:1. Perform the logout procedure (see Logout on page 4).2. At the console login prompt, type shutdown; the system begins theshutdown process.Note: Depending on your hardware, a Halt Completed prompt may appearand you may then switch off the computer. Otherwise your system will switch offon its own.
Page 3: Table of ContentsNotes & Informatio
Page 6: The text and drawings herein are fo
Page 11 and 12: Using This ManualWho Should Use Thi
Page 13 and 14: Additional DocumentationxiAdditiona
Page 15: Conventions Used in This Manualxiii
Page 18 and 19: 2 Chapter 1 - OverviewBrisque to Lo
Page 22 and 23: 6 Chapter 1 - OverviewWhat is Lotem
Page 24 and 25: 8 Chapter 1 - OverviewWhat is Lotem
Page 27 and 28: Configuring and Calibratingthe Lote
Page 29 and 30: Accessing the Output Device Configu
Page 31 and 32: Configuring the Lotem 800 II / Lote
Page 33 and 34: Configuring the Lotem 800 II / Lote
Page 35 and 36: Lotem 800 II / Lotem Quantum Plates
Page 37 and 38: Lotem 800 II / Lotem Quantum Plates
Page 39 and 40: Press Format 23Reset Screen Board i
Page 41 and 42: Press Format 254. Define Margins: H
Page 43 and 44: Excurve Calibration 273. Click Save
Page 45 and 46: Excurve Calibration 29Making a Test
Page 47 and 48: Excurve Calibration 31Creating the
Page 49 and 50: Excurve Calibration 33Additional pa
Page 51 and 52: Excurve Calibration 35Viewing an Ex
Page 53 and 54: Excurve Calibration 375. Develop th
Page 55 and 56: Excurve Calibration 39To define Aut
Page 57 and 58: Excurve Calibration 41Optional Excu
Page 59 and 60: Tone Reproduction 435. To select on
Page 61 and 62: Tone Reproduction 458. Entering Ton
Page 63 and 64: Tone Reproduction 476. Click OK; yo
Page 65 and 66: Tone Reproduction 492. To display t
Page 67 and 68: Screen Sets 51To configure the Maxi
Page 69 and 70: Screen Sets 53Important: A screen s
Page 71 and 72:
Screen Sets 556. Click Done to retu
Page 73 and 74:
Screen Sets 57Adding User CommentsY
Page 75 and 76:
Screen Sets 59To define a Screen Fr
Page 77 and 78:
Screen Sets 613. Press ENTER. The n
Page 79:
Screen Sets 63Automatic Definitions
Page 83 and 84:
Processing a Job on theLotem 800 II
Page 85 and 86:
Overview 693. Define the Plate Expo
Page 87 and 88:
Aligning Signature Elements 71Align
Page 89 and 90:
Aligning Signature Elements 73Viewi
Page 91 and 92:
Launching the Job to a Brisque Temp
Page 93 and 94:
Launching the Job to a Brisque Temp
Page 95 and 96:
Defining the Plate Expose Parameter
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Defining the Store Parameters 85Def
Page 103 and 104:
Defining the Store Parameters 87•
Page 105 and 106:
Submitting the Job Ticket for Proce
Page 107 and 108:
Performing a Plate Remake 91To perf
Page 109 and 110:
Performing a Plate Remake 936. Clic
Page 111:
Sending the Job for Long Term Stora
Page 114 and 115:
98 Chapter 4 - Configuring and Cali
Page 116 and 117:
100 Chapter 4 - Configuring and Cal
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
112 Chapter 5 - Proofing a Job on t
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
134 Brisque to Lotem 800 II / Lotem
show all

Brisque to Lotem 800 II / Lotem Quantum Family - Kodak

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?