Brisque to Lotem 800 II / Lotem Quantum Family - Kodak

More documents

Recommendations

Info

70 Chapter 3 – Processing a Job on the Lotem 800 II / Lotem Quantum from the Brisque WorkstationThe Job is RIPped and previewed on the local Brisque, and then sent to aremote Brisque for proofing. Due to Hold, you can check the proof beforereturning the Job to the Queue. Once you release the Job from hold, it issent to another Brisque for Expose, and when the Expose operation iscomplete, the Job and all its elements are sent, using Store, to a temporaryor final destination for storage.Note: Although Proof and Plate Expose are performed on remote Brisquestations, the template on the local Brisque defines the parameters.
Aligning Signature Elements 71Aligning Signature ElementsFront & Back PreviewLaunch Brisque Jobto Brisque TemplateDefine Plate ExposeparametersDefine Store parametersIn this chapter you will launch the Preview application on a singlesignature Layout with front and back flats. This is particularly useful in afilmless CTP environment, allowing you to reposition and correct thesignature elements on the screen, without returning to the Imposition filein Preps, and thereby preventing the need for wasting test plates to confirmalignment.We refer to a Brisque Imposition Job as the sample Job in this chapter.Browse the contents of your Brisque volume to find a similar type of file,that contains two Layouts with either four or eight Pages in each flat (thatis, an 8-up 16 Page Imposition Job for the Lotem 800 II / Lotem 800 IIQuantum or a 4-up 8 page Imposition Job for the Lotem 400 Quantum).Submit Job TicketEmergency plate remakeLong Term StorageThe complete functionality of Preview is described in the Previewing ImpositionJobs and Working with a Layout chapters in the Brisque 4.0 User Guide.Front and Back PreviewUsing Front and Back Preview in the Preview application, you can confirmthe alignment of the front and back flats within a Signature. Byrepositioning the Pages within the Layout section, you can easily correctthe Signature without having to return to the Imposition file.Note: Front and Back Preview is only available for an Imposition Job with doublesidedLayouts.The following terminology describes the way flats are related to in theFront and Back Preview tool:FrontBackRefers to the upper flat of a printed Signature.Refers to the lower flat of a printed Signature.
Page 3:
Table of ContentsNotes & Informatio
Page 6:
The text and drawings herein are fo
Page 11 and 12:
Using This ManualWho Should Use Thi
Page 13 and 14:
Additional DocumentationxiAdditiona
Page 15:
Conventions Used in This Manualxiii
Page 18 and 19:
2 Chapter 1 - OverviewBrisque to Lo
Page 20 and 21:
4 Chapter 1 - OverviewIf during the
Page 22 and 23:
6 Chapter 1 - OverviewWhat is Lotem
Page 24 and 25:
8 Chapter 1 - OverviewWhat is Lotem
Page 27 and 28:
Configuring and Calibratingthe Lote
Page 29 and 30:
Accessing the Output Device Configu
Page 31 and 32:
Configuring the Lotem 800 II / Lote
Page 33 and 34:
Configuring the Lotem 800 II / Lote
Page 35 and 36: Lotem 800 II / Lotem Quantum Plates
Page 37 and 38: Lotem 800 II / Lotem Quantum Plates
Page 39 and 40: Press Format 23Reset Screen Board i
Page 41 and 42: Press Format 254. Define Margins: H
Page 43 and 44: Excurve Calibration 273. Click Save
Page 45 and 46: Excurve Calibration 29Making a Test
Page 47 and 48: Excurve Calibration 31Creating the
Page 49 and 50: Excurve Calibration 33Additional pa
Page 51 and 52: Excurve Calibration 35Viewing an Ex
Page 53 and 54: Excurve Calibration 375. Develop th
Page 55 and 56: Excurve Calibration 39To define Aut
Page 57 and 58: Excurve Calibration 41Optional Excu
Page 59 and 60: Tone Reproduction 435. To select on
Page 61 and 62: Tone Reproduction 458. Entering Ton
Page 63 and 64: Tone Reproduction 476. Click OK; yo
Page 65 and 66: Tone Reproduction 492. To display t
Page 67 and 68: Screen Sets 51To configure the Maxi
Page 69 and 70: Screen Sets 53Important: A screen s
Page 71 and 72: Screen Sets 556. Click Done to retu
Page 73 and 74: Screen Sets 57Adding User CommentsY
Page 75 and 76: Screen Sets 59To define a Screen Fr
Page 77 and 78: Screen Sets 613. Press ENTER. The n
Page 79: Screen Sets 63Automatic Definitions
Page 83 and 84: Processing a Job on theLotem 800 II
Page 85: Overview 693. Define the Plate Expo
Page 89 and 90: Aligning Signature Elements 73Viewi
Page 91 and 92: Launching the Job to a Brisque Temp
Page 93 and 94: Launching the Job to a Brisque Temp
Page 95 and 96: Defining the Plate Expose Parameter
Page 101 and 102: Defining the Store Parameters 85Def
Page 103 and 104: Defining the Store Parameters 87•
Page 105 and 106: Submitting the Job Ticket for Proce
Page 107 and 108: Performing a Plate Remake 91To perf
Page 109 and 110: Performing a Plate Remake 936. Clic
Page 111: Sending the Job for Long Term Stora
Page 114 and 115: 98 Chapter 4 - Configuring and Cali
Page 116 and 117: 100 Chapter 4 - Configuring and Cal
Page 128 and 129: 112 Chapter 5 - Proofing a Job on t
Page 136 and 137:
120 Chapter 5 - Proofing a Job on t
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
134 Brisque to Lotem 800 II / Lotem
show all

Brisque to Lotem 800 II / Lotem Quantum Family - Kodak

Create successful ePaper yourself

Delete template?

Save as template?