Brisque to Lotem 800 II / Lotem Quantum Family - Kodak

More documents

Recommendations

Info

44 Chapter 2 – Configuring and Calibrating the Lotem 800 II / Lotem Quantum Family from the Brisque Workstation7. Select the separations to which the new curve will apply. Click Sepsand select one of the options; type the exact name of the colorseparation into the Seps box and click Enter.Note: You can delete a spot color by selecting it and clicking Remove. You canrename a spot color by selecting it, clicking Rename and typing in the newname.
Tone Reproduction 458. Entering Tone Reproduction curve values. The Edit Curve dialog boxshows the Tone Reproduction Curve values:• File Value —standard reference values based on a test exposure. Creorecommends using 21 different file values.• Required on Press—user-defined values for the density that isrequired on press. These values are based on correction valuesmade by an experienced technician, or intentional distortions usedfor special effects.• Measured on Press—the density values measured on the pressafter the Job is printed. Tone Reproduction automaticallycompares the measured values against the file values and creates acurve that corrects for dot gain.To enter curve values, click Enter and type a value in the appropriatetable cell.Tip: For accurate results, be sure to zero the densitometer to a “ghost” dotarea on the media before measuring the dot area.Note: Percent values are rounded off to the nearest tenth of a percent.9. To modify curve values, click on a row and modify the values.10. To delete curve values, click on the row and click Delete.Note: The end-points (0,0 and 100.0) can’t be modified or deleted.11. You can view the Tone Reproduction curve, which is actuallycomprised of two curves, Required and Measured.12. By default, the Curve type is Linear. If you want to smooth the curve,select Spline from the Curve Type list.13. You can add a descriptive comment into the Comment box; this textappears in the comment column of the Tone Reproduction Curve Listdialog box.14. Click Save As; the Save As dialog box opens.
Page 3:
Table of ContentsNotes & Informatio
Page 6:
The text and drawings herein are fo
Page 11 and 12: Using This ManualWho Should Use Thi
Page 13 and 14: Additional DocumentationxiAdditiona
Page 15: Conventions Used in This Manualxiii
Page 18 and 19: 2 Chapter 1 - OverviewBrisque to Lo
Page 20 and 21: 4 Chapter 1 - OverviewIf during the
Page 22 and 23: 6 Chapter 1 - OverviewWhat is Lotem
Page 24 and 25: 8 Chapter 1 - OverviewWhat is Lotem
Page 27 and 28: Configuring and Calibratingthe Lote
Page 29 and 30: Accessing the Output Device Configu
Page 31 and 32: Configuring the Lotem 800 II / Lote
Page 33 and 34: Configuring the Lotem 800 II / Lote
Page 35 and 36: Lotem 800 II / Lotem Quantum Plates
Page 37 and 38: Lotem 800 II / Lotem Quantum Plates
Page 39 and 40: Press Format 23Reset Screen Board i
Page 41 and 42: Press Format 254. Define Margins: H
Page 43 and 44: Excurve Calibration 273. Click Save
Page 45 and 46: Excurve Calibration 29Making a Test
Page 47 and 48: Excurve Calibration 31Creating the
Page 49 and 50: Excurve Calibration 33Additional pa
Page 51 and 52: Excurve Calibration 35Viewing an Ex
Page 53 and 54: Excurve Calibration 375. Develop th
Page 55 and 56: Excurve Calibration 39To define Aut
Page 57 and 58: Excurve Calibration 41Optional Excu
Page 59: Tone Reproduction 435. To select on
Page 63 and 64: Tone Reproduction 476. Click OK; yo
Page 65 and 66: Tone Reproduction 492. To display t
Page 67 and 68: Screen Sets 51To configure the Maxi
Page 69 and 70: Screen Sets 53Important: A screen s
Page 71 and 72: Screen Sets 556. Click Done to retu
Page 73 and 74: Screen Sets 57Adding User CommentsY
Page 75 and 76: Screen Sets 59To define a Screen Fr
Page 77 and 78: Screen Sets 613. Press ENTER. The n
Page 79: Screen Sets 63Automatic Definitions
Page 83 and 84: Processing a Job on theLotem 800 II
Page 85 and 86: Overview 693. Define the Plate Expo
Page 87 and 88: Aligning Signature Elements 71Align
Page 89 and 90: Aligning Signature Elements 73Viewi
Page 91 and 92: Launching the Job to a Brisque Temp
Page 93 and 94: Launching the Job to a Brisque Temp
Page 95 and 96: Defining the Plate Expose Parameter
Page 101 and 102: Defining the Store Parameters 85Def
Page 103 and 104: Defining the Store Parameters 87•
Page 105 and 106: Submitting the Job Ticket for Proce
Page 107 and 108: Performing a Plate Remake 91To perf
Page 109 and 110: Performing a Plate Remake 936. Clic
Page 111:
Sending the Job for Long Term Stora
Page 114 and 115:
98 Chapter 4 - Configuring and Cali
Page 116 and 117:
100 Chapter 4 - Configuring and Cal
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
112 Chapter 5 - Proofing a Job on t
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
134 Brisque to Lotem 800 II / Lotem
show all

Brisque to Lotem 800 II / Lotem Quantum Family - Kodak

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?