A-ISOMETERÂ® IRDH375 IRDH375B - Bender

More documents

Recommendations

Info

Operation and setting5.6 Menu COM SETUP: Setting the BMS interface5.6.1 Bus address „Addr:“ (IRDH375B)This menu item is used to set the BMS bus address of the IRDH375. Sincethere are several A-ISOMETERs in one system, take care that the bus addressis not assigned twice.The device is factory set to address 3 and hence acts as a slave.If several IRDH375 are operated on one BMS bus, the addresses of otherA-ISOMETERs must be assigned one after the other, since only one devicemay represent the Master.5.6.2 ISOnet function (IRDH375B)In the ISOnet = ON sub menu of the COM SETUP, the ISOnet function canbe set. The ISOnet function of all A-ISOMETERs existing in the system mustbe in "ON" position.A BMS Master with the ISOnet function activated, controls the ISOnet slavedevices via the BMS bus. If an A-ISOMETER® has completed the measuringcycle, the permission for insulation measurement is given from the ISOnetMaster to the next slave. During the measurement process carried out by anA-ISOMETER®, all other A-ISOMETERs® are in the STANDBY mode.5.6.3 ISO monitor (IRDH375B)This function allows to query the current measured value as well as the messagesof all bus-capable A-ISOMETERs existing in the BMS network. After selectingthe bus address, the entire information stored by the selected deviceis indicated on the display. The display indication is structured similar to thestandard indication, but instead of the indication of the measuring pulse, theselected bus address is indicated. Without pressing a key, the indicationchanges to the standard indication of the IRDH375B after about five minutes.If there is no information available from the selected A-ISOMETER®, themessage "!!!!NO DATA!!!!" will be displayed.Information is being searchedNo data foundCurrent data address 03R= K ADR:02!!!!NO DATA!!!!R= K ADR:02Insulation FaultR= 010K ADR:0348 TGH1352en/11.2004
Operation and setting5.6.4 Diagram COM SETUP (IRDH375B)*** IT-SYSTEM ***R >010 MWH1. EXIT2. HISTORY INFO3. ISO SETUP4. ISO ADVANCED5. COM SETUP6. PASSWORD7. LANGUAGE8. SERVICE1. Exit2. Addr: 0033. ISONet: off4. ISO MonitorAddr : 003ADR: 001..ADR: 030IRDH375IRDH375BISONet : off! ! ! ! NO DATA ! ! ! !R= ADR: 01ADR: 01.ADR: 30ISONet : offISONet : onTGH1352en/11.200449
Page 1 and 2: Operating ManualInsulationR =010KWf
Page 3 and 4: Table of Contents1. Safety informat
Page 5 and 6: Table of Contents5.6.1 Bus address
Page 7 and 8: 1. Safety information1.1 Use for th
Page 9 and 10: Safety information1.2.4 Inspection,
Page 11 and 12: Safety information1.4 Directions fo
Page 13 and 14: 2. Function2.1 Common characteristi
Page 15 and 16: Functionmessage, provided that the
Page 17 and 18: Function2.5 Additional functions IR
Page 19 and 20: FunctionISOnet Function (COM SETUP)
Page 21 and 22: 3. Commissioning flow chart (threep
Page 23 and 24: Commissioning flow chart (threepart
Page 25 and 26: 4. Connection4.1 WiringIRDH375(B) h
Page 27 and 28: ConnectionLegend to wiring diagram:
Page 29 and 30: Connection4.2.2 Connection with AGH
Page 31 and 32: ConnectionIn case of current-contro
Page 33 and 34: 5. Operation and setting5.1 Operati
Page 35 and 36: Operation and setting5.1.3 Function
Page 37 and 38: Operation and settingTGH1352en/11.2
Page 39 and 40: Operation and setting5.2.1 Diagram
Page 41 and 42: Operation and setting5.3.1 Diagram
Page 43 and 44: Operation and settingDiagram ISO SE
Page 45 and 46: Operation and setting5.5 Menu ISO A
Page 47: Operation and setting5.5.8 Diagram
Page 51 and 52: Operation and setting5.8 Menu LANGU
Page 53 and 54: 6. Serial interfacesThe A-ISOMETERs
Page 55 and 56: Serial interfaces6.2 RS485 interfac
Page 57 and 58: Serial interfaces6.4 BMS protocol (
Page 59 and 60: Serial interfacesThe following tabl
Page 61 and 62: 7. Technical data IRDH375(B)7.1 Dat
Page 63 and 64: Technical data IRDH375(B)General da
Page 65 and 66: Technical data IRDH375(B)7.3 Charac
Page 67 and 68: Technical data IRDH375(B)Current ou
Page 69 and 70: Technical data IRDH375(B)Current ou
Page 71 and 72: Technical data IRDH375(B)Dimension
Page 73 and 74: Technical data IRDH375(B)7.4.3 Coup
Page 75 and 76: INDEXAAGH... 28Alarm LED 1 33Alarm
Page 77 and 78: INDEX77 TGH1352en/11.2004

A-ISOMETERÂ® IRDH375 IRDH375B - Bender

Create successful ePaper yourself

Delete template?

Save as template?