CONVENTIONAL FIRE PANELS - Kotesa

More documents

Recommendations

Info

This Control panel can be programmed using the respective Software J400 release 1.0 or higher.BENTEL SECURITYsrl shall not assume the responsibility for damage arising from improper application or use.This Control panel has been designed and manufactured to the highest standards of quality and performance.Installation of this Control panel must be carried out strictly in accordance with the instructions described in this manual, andin compliance with the local laws and bylaws in forceThe J424 and J408 Control panels comply with the essential requirements of standards EN54-2; EN54-4.The J424 and J408 Control panels, all their accessories and functions, except those listed below and unless otherwise specified(see notes marked A), are IMQ Security Systems Grade II Listed.The J400-EXT Extinguishment Module is not IMQ Security Systems Grade II Listed.BENTEL SECURITY srl reserves the right to change the technical specifications of these products without prior notice.
TABLE OF CONTENTSINTRODUCTION 5The J424 and J208 Control panels 5Accessory Items 5Description 5Inputs 5Outputs 6Operating features 6Interface 7Extinguishment Module 8Access to Signalling and Commands 8Power Supply 8IDENTIFICATION OF PARTS 9The Status LEDs 9Description of Parts 14Description of the Control keys 20INSTALLING THE CONTROL PANEL 21Installing accessory boards 21Installing Extinguishment Modules 21Installing Expander Module Kit (for J424 ONLY) 22Display Module (for J424 and J400-REP ONLY) 24Installing Repeaters 25Installing the Control panel 25Description of the Terminals 25Main Board and Expander Board terminals 25Main Board Terminals 26Extinguishment Module Terminals 28Extinguishment Module 4Pre-extinguishment Phase 5Extinguishment Phase 5Manual Extinguishment 5Disable Extinguish. button 5Disable Manual Extinguish. button 5The System Wiring 29Connecting Fire Detectors 29Connecting Call-points 30Connecting Gas Detectors 30Connecting Signalling Devices 31Connecting a Repeater 32Connecting Extinguishment Modules 33Connecting a Power Supply 34Connecting the Mains Supply 34Thermal Probe 35Maintenance 35
Page 1: CONVENTIONALFIRE PANELS424408INSTAL
Page 5 and 6: INTRODUCTIONThe J424 and J208 Contr
Page 7 and 8: The Control panel will activate the
Page 9: IDENTIFICATION OF PARTSThe Status L
Page 12 and 13: NCNOC6 7 8 9 10 1131 3029Figure 2 M
Page 14 and 15: NCNOCDescription of PartsThis secti
Page 16 and 17: P. Description33 Anchor screw locat
Page 18 and 19: P. Description37 Battery output vol
Page 20 and 21: LED ON FaultElectrovalveGlowing ind
Page 22 and 23: 4. Using the Jumper (43), marked
Page 24 and 25: Display Module (for J424 and J400-R
Page 26 and 27: A IMQ-SECURITY SYSTEMS certificatio
Page 28 and 29: Extinguishment Module TerminalsEM S
Page 30 and 31: Standby statusOnly the green Mains
Page 32 and 33: Access Level 2Most of the functions
Page 34 and 35: EVENTS DETAILS DESCRIPTION24R OUT F
Page 36 and 37: Mains (GREEN) If OFF check for loca
Page 38 and 39: Wiring instructions for this featur
Page 40 and 41: Main boardRS48524VConnectto the ear
Page 42 and 43: Connecting a Power Supply!The power
Page 44 and 45: 29,0a)VOLTAGE (V)28,027,427,026,0-1
Page 46 and 47: Activation ModeThis section will al
Page 48 and 49: OptionsThis section will allow you
Page 50 and 51: Day to Night Mode This field will a
Page 52 and 53:
44 Conventional Fire Panels J424/J4
Page 54 and 55:
MMM 640 sec - - Zone 1Zone 5 Pre-al
Page 56 and 57:
4. Go back to step 1 to program ano
Page 58 and 59:
Use the Increase Time option (Key 8
Page 60 and 61:
TERM. DESCRIPTION v(V) i(A)[DL][OC]
Page 62 and 63:
54 Conventional Fire Panels J424/J4
Page 64:
®BENTEL SECURITY s.r.l.Zona Ind. S
show all

CONVENTIONAL FIRE PANELS - Kotesa

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?