CONVENTIONAL FIRE PANELS - Kotesa

More documents

Recommendations

Info

EVENTS DETAILS DESCRIPTION24R OUT FAULT None 24R output shorted24R OUT RESTORE None 24R output previously shorted24V OUT FAULT None 24V output shorted24V OUT RESTORE None 24V output previously shortedALARM ZONE Zone no. + Description Zone no. is in Alarm statusAUTO UNBYPASSED Extinguishment Mod. nr. Automatic Extinguishment of Extinguishment Mod. nr. re-enabledBATT.CHARG.FAULT Power Supply Stat. nr. Charger of Power Supply Stat. nr. not operating properlyBATT.CHARG.REST. Power Supply Stat. nr. Charger of Power Supply Stat. nr. previously not workingBATTERY DISCONN. Power Supply Stat. nr. Batteries of Power Supply Stat. nr. disconnectedBATTERY FAULT None Panel batteries empty, malfunctioning or disconnectedBATTERY FAULT Power Supply Stat. nr. Batteries of Power Supply Stat. nr. empty or disconnectedBATTERY FAULT Power Supply Stat. nr. Batteries of Power Supply Stat. nr. lowBATTERY RECONN. Power Supply Stat. nr. Batteries of Power Supply Stat. nr. previously disconnectedBATTERY RESTORE Power Supply Stat. nr. Batteries of Power Supply Stat. nr previously lowBATTERY RESTORE None Panel batteries previously empty, malfunctioning or disconnectedBATTERY RESTORE Power Supply Stat. nr. Batteries of Power Supply Stat. nr. empty or disconnectedBUZZER SILENCED None Buzzer disabledBYPASSED ZONE Zone no. + Description Zone no. disabledDETECTOR MISSING Zone no. + Description A detector connected to zone no. is missingDIALLER ACTIVATE None Dialler Output activeDISAB.AUTOExtinguishment Mod. nr. Automatic Extinguishment of Extinguishment Mod. nr.i disabledDL OUT FAULT None Dialler connections interrupted or shortedDL OUT RESTORE None Dialler connections interrupted or shortedDL OUTPUT Enabled/Disabled The Dialler Output has been disabled/enabledEM ACTIVATED Extinguishment Mod. nr. EM Input of Extinguishment Mod. nr. activatedEM INPUT FAULT Extinguishment Mod. nr. EM Input of Extinguishment Mod. nr. shorted or openEM INPUT RESTORE Extinguishment Mod. nr. EM Input of Extinguishment Mod. nr. previously shorted or openEV OUT ACTIVATED Extinguishment Mod. nr. EV Output of Extinguishment Mod. nr. activatedEV OUT FAULT Extinguishment Mod. nr. EV Output of Extinguishment Mod. nr. shorted or openEV OUT RESTORE Extinguishment Mod. nr. EV Output of Extinguish. Mod. nr. previously shorted or openEVACUATE None Evacuation command executedGND FAULT REST. None Control panel ground fault restoredGROUND FAULT None Control panel leakage to EarthIE ACTIVATED Extinguishment Mod. nr. IE Input of Extinguishment Mod. nr. activatedIE INPUT FAULT Extinguishment Mod. nr. IE Input of Extinguishment Mod. nr. shorted or openIE INPUT RESTORE Extinguishment Mod. nr. IE Input of Extinguishment Mod. nr. previously shorted or openINVESTIGATION None Investigation DoneMAIN FAULTNone/Pow.SupStat.nr. Mains failure to Control panel/Power Supply Stat. nr.MAIN RESTORE None The Control panel/Power Supply Stat. nr. powered from MainsMANUAL BYPASSED Extinguishment Mod. nr. EM Input of Extinguishment Mod. nr. disabledMANUAL UNBYPASS. Extinguishment Mod. nr. EM Input of Extinguishment Mod. nr re-enabledMODE Night/Day Control panel switched from Night to Day ModeNAC OUTPUT Enabled/Disabled One of the Alarm outputs has been disabled/enabledNAC1 FAULT None Alarm device connections interrupted or shortedNAC1 RESTORE None Alarm device connections interrupted or shortedNAC2 FAULT None Alarm device connections interrupted or shortedNAC2 RESTORE None Alarm device connections interrupted or shortedOUT 1 RESTORE Power Supply Stat. nr. O1 Output of Power Supply Stat. nr shortedOUT 1 SHORT Power Supply Stat. nr. O1 Output of Power Supply Stat. nr shortedOUT 2 RESTORE Power Supply Stat. nr. O2 Output of Power Supply Stat. nr shortedOUT 2 SHORT Power Supply Stat. nr. O2 Output of Power Supply Stat. nr shortedOUTS BYPASSED Extinguishment Mod. nr. Extinguishment Mod. PR, EV and AV outputs disabledOUTS UNBYPASSED Extinguishment Mod. nr. Extinguishment Mod. PR, EV and AV outputs re-enabledPE OUT ACTIVATED Extinguishment Mod. nr. PR Output of Extinguishment Mod. nr. activatedPE OUT FAULT Extinguishment Mod. nr. PR Output of Extinguishment Mod. nr. shorted or openPERIPHERAL FAULT Peripheral type and nr. The device concerned missing or faultyPERIPHERAL REST. Extinguishment Mod. nr. PR Output of Extinguish. Mod. nr. previously shorted or openPERIPHERAL REST. Device type+Number The device concerned previously missing or faultyTable 2 Event Descriptions (Continues ...): AV = Extinguishment Done; EM = Manual Extinguishment; EV = Electrovalve;IE = Inhibit Extinguishment ; PR = Pre-extinguishment; PS = Pressure switch.6 Conventional Fire Panels J424/J408
EVENTS DETAILS DESCRIPTIONPS ACTIVATED Extinguishment Mod. nr. PS Input of Extinguishment Mod. nr. activatedPS INPUT FAULT Extinguishment Mod. nr. PS Input of Extinguishment Mod. nr. shorted or openPS INPUT RESTORE Extinguishment Mod. nr. PS Input of Extinguish. Mod. nr. previously shorted or openRESET None Reset DoneRESTORE Zone no. + Description One of the zone detectors previously missingSILENCED None Silence DoneSWITCH.DISCONN. Power Supply Stat. nr. Switching Power Supply of Station nr. is disconnectedSWITCH.RECONN. Power Supply Stat. nr. Switching Power Supply of Station nr. previously disconnectedUNBYPAS.ZONE Zone no. + Description Zone no. was disabledZONE FAULT REST. Zone no. + Description Zone no. previously shorted or openZONE OPEN Zone no. + Description Zone no. is openZONE PREALARM Zone no. + Description Zone no. is in Pre-alarm statusZONE SHORT Zone no. + Description Zone no. shortedTable 2 Event Descriptions: AV= Extinguishment Done; EM = Manual Extinguishment; EV = Electrovalve; IE = InhibitExtinguishment ; PR = Pre-extinguishment; PS = Pressure switch.LoggerThe Control panel logger can store the Time, Date andDetails of 50 events.To view the events in the logger, proceed as follows.1. From standby status, press or to view theLOGGER:VIEWLOGGER2. Press Esc to step back or, press Enter to view thelast event in the Logger.ALARM ZONE15:46 18/10/2004The top line on the display will show the event (refer tothe DESCRIPTIONS column in Table 2), the bottomline will show when the event occurred (Time and Date).3. Use and to scroll back and forward in time theevents list, use to view the event details (see theDETAILS column in Table 2).ZONE 01Warehouse4. Repeat the previous step to continue viewing or,press Esc to step back.LED descriptionThe actions that must be carried out when the controlpanel LED’s go from standby status into alarm statusare explained, for each LED, following: when in standbystatus only the GREEN Mains LED should be lit.Some of the LED’s indicated below, as well as beingON, OFF or fast blinking, may also slow blinkingto indicate memory of the event they areassigned to.Alarm ON indicates that at least one zone is in alarmstatus (check the Zone Alarm LED’s of the zone in orderto check which zones are in alarm status); check forfalse alarm, if there is a real danger, spread the alarm,otherwise press the Silence button to silence momentarilythe silenceable alarm outputs or press the Resetbutton to disable all the alarm outputs.The Silence and Reset buttons can be used duringAccess Level 2 only.Pre-al. ON indicates Pre-alarm status. When the programmedPre-alarm time ends, the control panel will gointo Alarm status. In the event of false alarm - press theReset button to stop the automatic procedure.The Reset button can be used during Access Level2 only.Test ON indicates that at least one Zone is in Test status:check the Disabled/Fault/Test LEDs of the zonesin order to check which zones are in Test status, andcall assistance.Disab. ON indicates that at least one zone is disabled,and cannot generate fire alarms: check the Zone AlarmLEDs of the zones in order to check which zones are disabled.Telecom ON indicates that the devices assigned to firealarm signalling via telephone have been activated.USER’S INSTRUCTIONS 7
Page 1 and 2: CONVENTIONALFIRE PANELS424408INSTAL
Page 3 and 4: TABLE OF CONTENTSINTRODUCTION 5The
Page 5 and 6: INTRODUCTIONThe J424 and J208 Contr
Page 7 and 8: The Control panel will activate the
Page 9: IDENTIFICATION OF PARTSThe Status L
Page 12 and 13: NCNOC6 7 8 9 10 1131 3029Figure 2 M
Page 14 and 15: NCNOCDescription of PartsThis secti
Page 16 and 17: P. Description33 Anchor screw locat
Page 18 and 19: P. Description37 Battery output vol
Page 20 and 21: LED ON FaultElectrovalveGlowing ind
Page 22 and 23: 4. Using the Jumper (43), marked
Page 24 and 25: Display Module (for J424 and J400-R
Page 26 and 27: A IMQ-SECURITY SYSTEMS certificatio
Page 28 and 29: Extinguishment Module TerminalsEM S
Page 30 and 31: Standby statusOnly the green Mains
Page 32 and 33: Access Level 2Most of the functions
Page 36 and 37: Mains (GREEN) If OFF check for loca
Page 38 and 39: Wiring instructions for this featur
Page 40 and 41: Main boardRS48524VConnectto the ear
Page 42 and 43: Connecting a Power Supply!The power
Page 44 and 45: 29,0a)VOLTAGE (V)28,027,427,026,0-1
Page 46 and 47: Activation ModeThis section will al
Page 48 and 49: OptionsThis section will allow you
Page 50 and 51: Day to Night Mode This field will a
Page 52 and 53: 44 Conventional Fire Panels J424/J4
Page 54 and 55: MMM 640 sec - - Zone 1Zone 5 Pre-al
Page 56 and 57: 4. Go back to step 1 to program ano
Page 58 and 59: Use the Increase Time option (Key 8
Page 60 and 61: TERM. DESCRIPTION v(V) i(A)[DL][OC]
Page 62 and 63: 54 Conventional Fire Panels J424/J4
Page 64: ®BENTEL SECURITY s.r.l.Zona Ind. S

CONVENTIONAL FIRE PANELS - Kotesa

Create successful ePaper yourself

Delete template?

Save as template?