CONVENTIONAL FIRE PANELS - Kotesa

More documents

Recommendations

Info

Standby statusOnly the green Mains LED (and the Night Mode LED, ifthe Control panel is operating in Night Mode) will be onduring standby status, the display will show the timeand date and “PANEL WORKING” message:PANEL WORKING17:30 13/10/2004Pre-alarmIn the event of a fire, the Control panel will generatePre-alarm status, which will be signalled by: the devices set up by the installer; the Pre-al. LED (On); the Zone Alarm LEDs (On) of the zones concerned; an intermittent audible signal (0.5 second beep followedby a 0.5 second pause); a “PREALARM” message, similar to the following:PREALARMWarehouseThe bottom line will show the label (Description) of thezone that triggered the pre-alarm.During PREALARM status:Use or to scroll the zones in Pre-alarm status.If you do not strike a key within 20 seconds, the displaywill go back to the first zone that triggered thePre-alarm.Press Esc to access the Main menu.If you do not strike a key within 20 seconds, the displaywill show the first zone that triggered the Pre-alarm.Pre-alarm status will last for the pre-set Pre-alarm Time(refer to the following paragraph for details).AlarmThe Control panel will generate an instant Alarm, ifalarm conditions are detected during Night Mode(refer to “Night Mode”) or, if an alarm is triggeredfrom a Call point — connected to a zone with theCall point priority attribute (i.e. Call point priorityENABLED).Fire Alarms will be signalled by: the devices set up by the installer; the Alarm LED (On); the Zone Alarm LEDs (On) of the zones concerned; a fast intermittent audible signal (0.2 second beepfollowed by a 0.2 second pause); a “ALARM” message, similar to the following:ALARM ON ZONE 01WarehouseThe top line will show the number of the zone that triggeredthe Alarm; the bottom line will show the zone label(Description).During ALARM status:Use or to scroll the zones in Alarm status.If you do not strike a key within 20 seconds, the displaywill go back to the first zone that triggered the Alarm.Press Esc to view the Main menu.If you do not strike a key within 20 seconds, the displaywill go back to first zone that triggered the Alarm.If zones restore to standby spontaneously, the Alarmevents will be stored in the Memory and signalled on therespective Zone Alarm LEDs until you Reset the Controlpanel.FaultThe Fire Alarm Outputs will not restore to standby— even if Alarm conditions end beforehand — untilyou Reset the Control panel.The Control panel faults will be signalled by: the devices set up by the installer; the Fault LED (On); the relative Fault LED (On) — refer to Table 1; a slow intermittent audible signal (1 second beep followedby a 1 second pause); a message on the display, similar to the following (referto Table 1):FAULT ON ZONE 01WarehouseDuring FAULT status:Use or to scroll the Faults.If you do not strike a key within 20 seconds, the displaywill go back to the first fault that occurred.Press Esc to view the Main Menu.If you do not strike a key within 20 seconds, the displaywill go back to first Fault that occurred.If the Fault conditions clear, the Fault events will be storedin the Memory, and signalled by slow flashing on therespective LEDs.The Control panel will restore to standby when allthe Fault conditions clear.2 Conventional Fire Panels J424/J408
LED STAT. DISPLAY DESCRIPTION CONSEQUENCEDisabled FAULT ON ZONE 01 A detector is missing from The detectors downstream ofFast/Fault Warehousezone no. 1, or zone no. 1 is the missing detector will beblink./Testshorted or openunable to signal fire conditionsLogic UnitThe Control panel is blocked The Control panel will be una-ONMains (red)Disab./FaultTelecomGround24V/24RFastblink.Fastblink.ONFastblink.FAULTMain FaultFAULTDL OutputFAULTGround FaultFAULT24V OutputFAULT24R Outputble to functionThe Control panel is NOT poweredThe batteries will provide po-from the Mains wer until they empty.The Dialler Output is shorted The Telephone devices set upor opento send fire warnings will beLeakage to Earth24V Output is shorted24R Output is shortedunable to functionThe Control panel functionsmay be impairedThe devices connected to the24V Output will be unable tofunctionThe devices connected to the24R Output will be unable tofunctionBattery Fastblink.FAULTBatteryThe Control panel batteries areempty, faulty or disconnectedThe Panel may be unable tofunction in the event of black-outDisab./FaultNAC FastFAULTNAC 1 OutputThe NAC1 Output is shorted oropenThe devices connected to theNAC1 will be unable to functionblink. FAULTNAC 2 OutputThe NAC2 Output is shorted oropenThe devices connected to theNAC2 will be unable to functionPeriph. Fast FAULTThe Panel CANNOT communicatewith the peripherals the status of the PeripheralsThe Panel will be unable to readblink. PeripheralThe information in the following rows is valid for Extinguishment Module nr. 1 and Extinguishment Module n. 2Fault: FAULT ON EXT. 1 The power supply to the Electrovalveis interrupted or the Electro-CANNOT be activatedThe Extinguishment devicesFastElectrovalvvalveOutput is shorted orELECTROVALVEblink.openFault:Pre Ext.Fault:ManualExt.Fault:Disab.Ext.Fault:Pres.SwitchFastblink.Fastblink.Fastblink.Fastblink.FAULT ON EXT. 1PRE-EXT. OUTPUTFAULT ON EXT. 1MANUAL EXT.INPUTFAULT ON EXT. 1INHIB.EXT.INPUTFAULT ON EXT. 1PRES.SWITCH INP.The Pre-extinguishment Outputis shorted or openThe Panel will be unable to signalthe Pre-extinguishment phaseManual Extinguishment Input The Manual Extinguishmentis shorted or openbuttons CANNOT activate theThe Inhibit ExtinguishmentInput is shorted or openThe Pressure switch Input isshorted or openFault:The Extinguishment Module isONLogic UnitblockedThe information in the following rows is valid for all the Power Supply StationsFAULT POWER ST.1 The Power Supply Station isMain Faultnot powered from the MainsFAULT POWER ST.1Low BatteryFAULT POWER ST.1Battery FaultFAULT POWER ST.1Battery Disconn.FAULT POWER ST.1OUT 1FAULT POWER ST.1OUT 2Extinguishment phaseThe Inhibit Extinguishmentbuttons CANNOT inhibit theExtinguishment phaseThe Panel will be unable to gaugethe Extinguishment GaspressureThe Extinguishment Modulewill be unable to functionThe batteries will supply thePower Supply Station untilthey emptyThe Power Supply Station batteriesThe Power Supply Station mayare lowbe unable to function in theevent of black-outThe Power Supply Station batteriesThe Power Supply Station mayare low or disconnected be unable to function in theevent of black-outThe batteries of the Power The Power Supply Station maySupply Station has shutdown be unable to function in thedue to voltage dropevent of black-outThe Output nr. 1 of the Power The devices connected to theSupply Station is shorted Output 1 will be unable to functionThe Output nr. 2 of the Power The devices connected to theSupply Station is shorted Output 2 will be unable to functionTable 1 Fault Descriptions
Page 1 and 2: CONVENTIONALFIRE PANELS424408INSTAL
Page 3 and 4: TABLE OF CONTENTSINTRODUCTION 5The
Page 5 and 6: INTRODUCTIONThe J424 and J208 Contr
Page 7 and 8: The Control panel will activate the
Page 9: IDENTIFICATION OF PARTSThe Status L
Page 12 and 13: NCNOC6 7 8 9 10 1131 3029Figure 2 M
Page 14 and 15: NCNOCDescription of PartsThis secti
Page 16 and 17: P. Description33 Anchor screw locat
Page 18 and 19: P. Description37 Battery output vol
Page 20 and 21: LED ON FaultElectrovalveGlowing ind
Page 22 and 23: 4. Using the Jumper (43), marked
Page 24 and 25: Display Module (for J424 and J400-R
Page 26 and 27: A IMQ-SECURITY SYSTEMS certificatio
Page 28 and 29: Extinguishment Module TerminalsEM S
Page 32 and 33: Access Level 2Most of the functions
Page 34 and 35: EVENTS DETAILS DESCRIPTION24R OUT F
Page 36 and 37: Mains (GREEN) If OFF check for loca
Page 38 and 39: Wiring instructions for this featur
Page 40 and 41: Main boardRS48524VConnectto the ear
Page 42 and 43: Connecting a Power Supply!The power
Page 44 and 45: 29,0a)VOLTAGE (V)28,027,427,026,0-1
Page 46 and 47: Activation ModeThis section will al
Page 48 and 49: OptionsThis section will allow you
Page 50 and 51: Day to Night Mode This field will a
Page 52 and 53: 44 Conventional Fire Panels J424/J4
Page 54 and 55: MMM 640 sec - - Zone 1Zone 5 Pre-al
Page 56 and 57: 4. Go back to step 1 to program ano
Page 58 and 59: Use the Increase Time option (Key 8
Page 60 and 61: TERM. DESCRIPTION v(V) i(A)[DL][OC]
Page 62 and 63: 54 Conventional Fire Panels J424/J4
Page 64: ®BENTEL SECURITY s.r.l.Zona Ind. S

CONVENTIONAL FIRE PANELS - Kotesa

Create successful ePaper yourself

Delete template?

Save as template?