AS-700

More documents

Recommendations

Info

Pos: 101.4 /Bedienungsanleitungen/Geräte spezifisch/Drucker/Printer Driver & Cables to PC/USB 2.0 (619)/7.X.X_Ü3_How to identify the USB port number @ 3\mod_1296549141672_912.doc @ 29849 @ 2printer driver.The „Found New Hardware Wizard“ (see Figure 58) will appear eachtime the printer is turned on or plug into the PC. To avoid this youhave to install the printer driver version which is delivered togetherwith the printer.11.3.2 Ethernet connection1. Check theinstalledprinter driver2. Add aTCP/IP port tothe printerdriver3. Setup theEthernetconnection• Make sure that the already installed printer driver is the correctone for your new printer. For example the printer model <strong>AS</strong>-710requires the printer driver for the <strong>AS</strong>-710.• Add a “Standard TCP/IP Port” to the already installed printer driveras described in chapter 7.3.1, on page 89.• Setup the Ethernet connection between the printer and the PC asdescribed in 7.3, on page 88.11.4 How to identify the USB port used by the printerIn certain cases (e.g. further use of already installed printer drivers) it is necessary toidentify the exact USB port number, when the printer is connected to the PC via USB.As most PC’s nowadays have more than one physical USB port. The USB port number canbe used to identify the actual port where a device is plugged in.Depending on which PC USB port the printer is plugged in, the USB port number can be forexample USB001, USB002 or etc.1. Set theprinter to USBcommunication2. Connectingthe printer3. Devicedetection• Check if the printer is set to USB communication in the printermenu: PRINTER CONFIG. > BOOT DEFAULTS > COMMUNICATION• If not, set it to USB.• Connect the printer to the PC with the USB cable.• Turn on the printer.• Wait until Windows detects the printer.142 User Manual Version 3.1
4. Open theDeviceManager• Open the Widows Device Manager.Start > Control Panel > Hardware and Sound > Device ManagerUser Manual Version 3.1 143
Page 1 and 2:
As-700ADress PrINTerUser MANUAL
Page 4 and 5:
Table of Contents1 Introduction ...
Page 6 and 7:
Pos: 6 /[Allgemeines]/0.3_Abbildung
Page 8 and 9:
Pos: 7 /Bedienungsanleitungen/Gerä
Page 10 and 11:
Pos: 11 /Bedienungsanleitungen/Ger
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
3.4.2 How to mount the paper feed r
Page 22 and 23:
Page 24 and 25:
4.3.1 Key panelBelow is an explanat
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
separation fingersFigure 11: Separa
Page 36 and 37:
Page 38:
Page 41 and 42:
Page 44 and 45:
Pos: 61.3 /Bedienungsanleitungen/Ge
Page 46 and 47:
Page 48 and 49:
MAIN MENUThe Home key opens the mai
Page 50 and 51:
KEEP ALIVEHere you can turn on the
Page 52 and 53:
Pos: 61.26 /Bedienungsanleitungen/G
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Pos: 61.102 /Bedienungsanleitungen/
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
3. Install thedriver with theNew Ha
Page 86 and 87:
Page 88 and 89:
7.3.1 Adding a TCP/IP port to a pri
Page 90 and 91:
Page 92 and 93: 7.3.2.2 Using a dynamic IP address1
Page 94 and 95: 2. TCP/IPinterfaceconfigurationof t
Page 96 and 97: Pos: 64 /Bedienungsanleitungen/Ger
Page 108 and 109: Pos: 80.4 /Bedienungsanleitungen/Ge
Page 112 and 113: Pos: 80.18 /Bedienungsanleitungen/G
Page 126 and 127: os: 85.6 /Bedienungsanleitungen/Ger
Page 132 and 133: Pos: 92 /Zubehör/Generelles Zubeh
Page 136 and 137: os: 99 /Bedienungsanleitungen/Gerä
Page 150 and 151: 11.8 How to create a print fileDepe
Page 152 and 153: Pos: 105 /Serviceanleitungen/Gerät
Page 154 and 155: 4 • Enable “Send to printer”
Page 160 and 161: 12 GlossaryTermAddressingASCllBarco
Page 162 and 163: Font inclinationFont typeHP TIJ 2.5
Page 164 and 165: Printer DriverPrintheadPrinthead ca
Page 166 and 167: 13 IndexAccessories ...............
Page 168: 9204022X-Bedition 08/04/2011 - 9204
show all

AS-700

Create successful ePaper yourself

Delete template?

Save as template?