AS-700

More documents

Recommendations

Info

Pos: 53 /Bedienungsanleitungen/Geräte spezifisch/Drucker/AS-710/5.4_Ü2_Adjusting Printer to the material thickness_AS-700/710 @ 2\mod_1270546252633_912.doc @ 14277 @ 2paper sensor positionFigure 14: Position of paper sensor3. Fill thefeeder withmaterial• Put one piece of medium into the feeder.• Push the medium all the way to the separation fingers.• Shingle the pile.• Put the pile into the feeder.4.Adjustthepaperfeedramp• Set the tilt of the paper feed ramp according to your material:flexible material, small width = steep tiltinflexible material, large width = flat tilt• Push the runner towards the pile so that the bottom two or three productsare free from the weight of the pile (see Figure 15).Figure 15: Adjusting the runner36 User Manual Version 3.1
5.4 How to adjust the printer to the material thicknessTo ensure a sharp, clean print quality and a safe material transport, you have to adjust theprinter to the material thickness. Set the thickness adjustment knob to the following scalevalues:Scale valueMaterial thickness0 0.1 mm – 0.4 mm(e.g. empty envelope or 80 g/m² stock)1 0.4 mm – 0.8 mm2 0.8 mm – 2.0 mm3 2.0 mm – 3.5 mm4 3.5 mm – 5.0 mm5 5.0 mm – 6.0 mmIf you don’t know the thickness of your material, you should adjust the printer as describedbelow:• Open the transparent safety cover.• Lift the transport rollers and the movable exit rollers by turning the thicknessadjustment knob (see Figure 16) to the maximum thickness (scale value “5”).• Put one medium underneath the transport rollers (see Figure 17).• Lower the transport rollers and the movable exit rollers by turning the thicknessadjustment knob until the medium sits tightly between the rollers (you must still beable to move the medium!).• Pull out the medium and close the safety cover.Figure 16: Thickness adjustment knobUser Manual Version 3.1 37
Page 1 and 2: As-700ADress PrINTerUser MANUAL
Page 4 and 5: Table of Contents1 Introduction ...
Page 6 and 7: Pos: 6 /[Allgemeines]/0.3_Abbildung
Page 8 and 9: Pos: 7 /Bedienungsanleitungen/Gerä
Page 10 and 11: Pos: 11 /Bedienungsanleitungen/Ger
Page 20 and 21: 3.4.2 How to mount the paper feed r
Page 24 and 25: 4.3.1 Key panelBelow is an explanat
Page 34 and 35: separation fingersFigure 11: Separa
Page 38: Pos: 54 /Bedienungsanleitungen/Ger
Page 44 and 45: Pos: 61.3 /Bedienungsanleitungen/Ge
Page 48 and 49: MAIN MENUThe Home key opens the mai
Page 50 and 51: KEEP ALIVEHere you can turn on the
Page 52 and 53: Pos: 61.26 /Bedienungsanleitungen/G
Page 72 and 73: Pos: 61.102 /Bedienungsanleitungen/
Page 84 and 85: 3. Install thedriver with theNew Ha
Page 86 and 87:
Pos: 62.3 /Bedienungsanleitungen/Ge
Page 88 and 89:
7.3.1 Adding a TCP/IP port to a pri
Page 90 and 91:
Page 92 and 93:
7.3.2.2 Using a dynamic IP address1
Page 94 and 95:
2. TCP/IPinterfaceconfigurationof t
Page 96 and 97:
Pos: 64 /Bedienungsanleitungen/Ger
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Pos: 80.18 /Bedienungsanleitungen/G
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
os: 85.6 /Bedienungsanleitungen/Ger
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Pos: 92 /Zubehör/Generelles Zubeh
Page 134 and 135:
Page 136 and 137:
os: 99 /Bedienungsanleitungen/Gerä
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
11.8 How to create a print fileDepe
Page 152 and 153:
Pos: 105 /Serviceanleitungen/Gerät
Page 154 and 155:
4 • Enable “Send to printer”
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
12 GlossaryTermAddressingASCllBarco
Page 162 and 163:
Font inclinationFont typeHP TIJ 2.5
Page 164 and 165:
Printer DriverPrintheadPrinthead ca
Page 166 and 167:
13 IndexAccessories ...............
Page 168:
9204022X-Bedition 08/04/2011 - 9204
show all

AS-700

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?