AS-700

More documents

Recommendations

Info

Pos: 62.6 /Bedienungsanleitungen/Geräte spezifisch/Drucker/Printer Driver & Cables to PC/TCP /IP (619)/7.2.1_Ü3_Connecting the printer to a network_ONLY_619 @ 3\mod_1289307329445_912.doc @ 28163 @ 344Figure 45: Address printer port settings90 User Manual Version 3.1
7.3.2 Connecting the printer to a local area networkConfiguration of network settingsTo connect the printer to a LAN it is necessary to perform certainconfigurations on the server of your LAN.Please contact your company’s network administrator for support.Connect theprinter to theLAN• Connect the printer to the LAN with the Ethernet cableInsert one Ethernet connector of the cable into the Ethernetinterface of the printer and insert the other connector into anEthernet port of the LAN.• Configure the TCP/IP interface of the printer. There are twooptions for the configuration of the printer’s TCP/IP interface:• Fix IP• Dynamic IP7.3.2.1 Using a fixed IP addressPlease read the descriptions for these two options below andchoose the one the fits best to your network.1. Printersettings “fixIP”• Open the main menu of the printer with the Home key.• Open the menu PRINTER CONFIG. > BOOT DEFAULTS >COMMUNICATION > TCP/IP.• In this menu select the setting fix IP.In the next menu you can set the values for Port Number, IPAddress, Subnet Mask and Gateway IP Address.Port numberIP AddressSubnet MaskGateway IP AddressThe default port 9100 is commonly used by printers. Please makesure that this port is not blocked in your LAN or use a port numberthat is accessible in your LAN.Please enter an IP address that is valid with your LAN.Please enter the Subnet Mask of your LAN.Please enter the IP address of the server of your LAN.2. Enter/change thedefaultsettings• The printer default values are shown below.Port Number: 9100IP Address: 192.168.50.180Subnet Mask: 255.255.255.0Gateway IP Address: 192.168.50.180• Confirm any changes to the values by pressing the Ok key. Nowpress the Cancel key until the main view is shown in the display.• Press the Ok key to turn the printer online. The bottom line ofthe display must now show: OnlinTCPUser Manual Version 3.1 91
Page 1 and 2:
As-700ADress PrINTerUser MANUAL
Page 4 and 5:
Table of Contents1 Introduction ...
Page 6 and 7:
Pos: 6 /[Allgemeines]/0.3_Abbildung
Page 8 and 9:
Pos: 7 /Bedienungsanleitungen/Gerä
Page 10 and 11:
Pos: 11 /Bedienungsanleitungen/Ger
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
3.4.2 How to mount the paper feed r
Page 22 and 23:
Page 24 and 25:
4.3.1 Key panelBelow is an explanat
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
separation fingersFigure 11: Separa
Page 36 and 37:
Page 38:
Page 41 and 42: Pos: 60 /Bedienungsanleitungen/Ger
Page 44 and 45: Pos: 61.3 /Bedienungsanleitungen/Ge
Page 48 and 49: MAIN MENUThe Home key opens the mai
Page 50 and 51: KEEP ALIVEHere you can turn on the
Page 52 and 53: Pos: 61.26 /Bedienungsanleitungen/G
Page 72 and 73: Pos: 61.102 /Bedienungsanleitungen/
Page 84 and 85: 3. Install thedriver with theNew Ha
Page 88 and 89: 7.3.1 Adding a TCP/IP port to a pri
Page 92 and 93: 7.3.2.2 Using a dynamic IP address1
Page 94 and 95: 2. TCP/IPinterfaceconfigurationof t
Page 126 and 127: os: 85.6 /Bedienungsanleitungen/Ger
Page 132 and 133: Pos: 92 /Zubehör/Generelles Zubeh
Page 136 and 137: os: 99 /Bedienungsanleitungen/Gerä
Page 140 and 141:
Pos: 101.3 /Bedienungsanleitungen/G
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
11.8 How to create a print fileDepe
Page 152 and 153:
Pos: 105 /Serviceanleitungen/Gerät
Page 154 and 155:
4 • Enable “Send to printer”
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
12 GlossaryTermAddressingASCllBarco
Page 162 and 163:
Font inclinationFont typeHP TIJ 2.5
Page 164 and 165:
Printer DriverPrintheadPrinthead ca
Page 166 and 167:
13 IndexAccessories ...............
Page 168:
9204022X-Bedition 08/04/2011 - 9204
show all

AS-700

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?