warning - Docs.hvacpartners.com

More documents

Recommendations

Info

59TP5AHORIZONTAL LEFT -VERTICAL VENT CONFIGURATIONHORIZONTAL LEFT -LEFT VENT CONFIGURATIONHORIZONTAL LEFT -RIGHT VENT CONFIGURATION**Requires Accessory Internal Vent KitSee Product Data for Current Kit Number1234567Attach vent pipe adapter with gasket to furnace casing.Align notches in rubber coupling over standoffs on adapter. Slide clamps over the coupling.Slide vent pipe through adapter and coupling into vent elbow.Insert vent pipe into vent elbow.Torque all clamps 15 lb.-in.Attach combustion air pipe adapter with gasket to furnace.Attach combustion air pipe to adapter with silicone. Pilot drill a 1/8-in.hole in adapter and secure with a #7 x 1/2-in sheet metal screw.Fig. 41 - Horizontal LeftA1134050
HORIZONTAL RIGHT -VERTICAL VENT CONFIGURATIONHORIZONTAL RIGHT -LEFT VENT CONFIGURATION**Requires Internal Vent KitSee Product Data for Current Kit Number59TP5AHORIZONTAL RIGHT -RIGHT VENT CONFIGURATION1234567Attach vent pipe adapter with gasket to furnace casing.Align notches in rubber coupling over standoffs on adapter. Slide clamps over the coupling.Slide vent pipe through adapter and coupling into vent elbow.Insert vent pipe into vent elbow.Torque all clamps 15 lb.-in.Attach combustion air pipe adapter with gasket to furnace.Attach combustion air pipe to adapter with silicone. Pilot drill a 1/8-in.hole in adapter and secure with a #7 x 1/2-in sheet metal screw.Fig. 42 - Horizontal RightA1134151
Page 3 and 4: SAFETY CONSIDERATIONS! WARNINGFIRE,
Page 5 and 6: 6. Before removing a new control fr
Page 7 and 8: !LOCATIONCAUTIONPERSONAL INJURY AND
Page 9 and 10: Fig. 4 - Prohibited InstallationsA1
Page 11: FURNACEINPUT(BTUH)Table 3 - Minimum
Page 14 and 15: Remove pressure switch tube fromfro
Page 16 and 17: 5If alternate vent positionis requi
Page 18 and 19: INSTALL CLAMPS ON DRAIN TUBEATTACH
Page 20 and 21: 59TP5AINSTALLATIONUpflow Installati
Page 22 and 23: FURNACE CASING WIDTH14---3/16 (360)
Page 24 and 25: FURNACE(OR COIL CASINGWHEN USED)FUR
Page 26 and 27: 59TP5AANY COMBINATION OF 1, 2, OR 3
Page 28 and 29: 59TP5AAIR DUCTSGeneral Requirements
Page 30 and 31: NOMINALIRON PIPESIZEIN. (MM)Table 8
Page 32 and 33: 59TP5A8. Attach furnace J-Box cover
Page 34 and 35: 1To Humidifier LeadsTo HUM Terminal
Page 36: NOTES FOR THERMOSTAT WIRING DIAGRAM
Page 39 and 40: Allowable vent and combustion air t
Page 41 and 42: 6. Tighten the clamp around the out
Page 43 and 44: Table 12 - Maximum Allowable Expose
Page 45 and 46: Table 15 - Maximum Equivalent Vent
Page 47 and 48: 76Any other unusedknockout may be u
Page 49: Rotate vent elbow torequired positi
Page 53 and 54: VV59TP5AItem Clearance Description
Page 55 and 56: Roof T e rm ination (Pref erred)At
Page 57 and 58: Ventilated CombustionAir intake pip
Page 59 and 60: In Canada, the input rating must be
Page 61 and 62: !CAUTIONFURNACE OVERHEATING HAZARDF
Page 63 and 64: 59TP5AFig. 54 - Service Label Infor
Page 65 and 66: U.S.A. and CanadaU.S.A. Only U.S.A.
Page 67 and 68: SERVICE AND MAINTENANCEPROCEDURES!
Page 69 and 70: !CAUTIONCUT HAZARDFailure to follow
Page 71 and 72: fully seated forward in the burner
Page 73 and 74: NOTE: No thermostat signals may be
Page 75 and 76: 59TP5AFig. 60 - Blower AssemblyA113
Page 77 and 78: the high -heat pressure switch HPS
Page 79 and 80: memory to be automatically used fol
Page 81 and 82: 11 NO PREVIOUS CODE - Stored codes
Page 83 and 84: PARTS REPLACEMENT INFORMATION GUIDE

warning - Docs.hvacpartners.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?