Glanded Pumps - THERMO-ECO-ENGINEERING úvod

Recommendations

Info

Pump Management Systems Wilo-Control Control Technology Wilo-Control DigiCon Wilo-Control DigiCon The Wilo-Control DigiCon interface converter is suitable for the universal linkage of communications-compatible pumps with the PLR interface to be found at onsite control and monitoring units that have the RS 485 digital serial interface. It is installed on a top-hat rail (DIN EN50 022-35) in a switch cabinet in the immediate vicinity of the monitoring unit. The Wilo-Control DigiCon interface converter transforms the two-wire connection of the PLR serial digital interface into a bus-compatible RS 485 serial digital interface. A maximum of 4 single or twin-head pumps of the following Wilo series can be linked to the BA by means of the Wilo-Control DigiCon interface converter: - TOP-E / -ED (with IF-Modul PLR) -Stratos/-D/-Z/-ZD (with IF-Modul Stratos PLR) - VeroLine-IP-E (with IF-Modul PLR) - VeroTwin-DP-E (with IF-Modul PLR) - CronoLine-IL-E (with IF-Modul PLR) - CronoTwin-DL-E (with IF-Modul PLR) The bidirectional communication between the pumps and the monitoring unit (BA) makes it possible to select between the following types of regulation and control units: - p-c for constant differential pressure - p-v for variable differential pressure - p-T for temperature-prompted differential pressure - n-c for constant speed Bidirectional communication between the pumps and the monitoring unit (BA) makes possible remote control of: -Pump Off - Pump in control mode ON -Maximum speed - Minimum speed (setback mode) - Setpoint for the preselected type of regulation or control Bidirectional communication between the pumps and the monitoring unit (BA) makes possible remote query of: - Current operating mode - Collective fault signal - Detailed fault signal - Individual run signal MA or individual pump - Individual run signal SL (twin-head pump only) as well as the following operating parameters of the pumps: - Actual delivery head and current volumetric flow - Motor current -Power consumption - Operating hours - Cumulative power consumption -Speed - Pumped liquid temperature (only TOP-E / -ED and Stratos / -D / -Z / -ZD) In addition to remote control and remote query, the Wilo-Control DigiCon interface converter also makes possible local adjustment of: - p-c for constant differential pressure - p-v for variable differential pressure - n-c for constant speed - Setpoint for differential pressure or speed The Wilo-Control DigiCon interface converter is equipped with LEDs for: - Operational state DigiCon - Communication with the pump - Communication with interface RS 485 With the interface RS 485, a maximum of 64 Wilo-Control DigiCon interface converters can be switched in series. Technical Data • Supply voltage - Operating voltage: 24 VDC ± 25 % - Current consumption: 70 mA - Terminal cross-section: 1.5 mm 2 • Electromagnetic compatibility - Emitted interference: DIN EN 61000-6-3 - Immunity to interference: DIN EN 61000-6-2 • Interface PLR - Point-to-point interface with Wilo-specific hardware and Wilo-specific protocol - Two-wire connection with interchangeable cores (no shielded cable necessary) - Maximum cable length: 200m - Cable type: e.g. J-Y(St)Y 2x2x0.8 - Terminal cross-section: 1.5 mm 2 • Interface RS 485 Bus-compatible interface with hardware in accordance with the RS 485 standard and the Wilo-specific protocol. The protocol is to be co-ordinated with respective BA manufacturer. - Addressing of a maximum of 64 DigiCons (maximum of 256 pumps) - Maximum total length of the bus line: 1000 m - Cable type: e.g. J-Y(St)Y 2x2x0.8, shielded - Terminal cross-section: 1.5 mm 2 Documentation of the Wilo-specific protocol is stored on the CD included in the scope of delivery. The software provided on this CD also enables communications between the pumps and a conventional PC. Manual operation of the pump by means of the red knob is not possible if the pump is connected to the Wilo-Control DigiCon. A temporary disruption of the interface connection to electronically controlled pumps with IR interface is possible with the IR-Monitor. The operation can then be controlled with the IR-Monitor. Interface communication is automatically restored after the IR connection is disconnected. Accessories Manual operation level Wilo-Control DigiCon-A for a maximum of 2pumps 216 Subject to change without prior notice 09/2006 WILO AG
Pump Management Systems Wilo-Control Control Technology Wilo-Control DigiCon-A Wilo-Control DigiCon-A I 0 I 0 I 0 Bus Controller Stratos-D Stratos Dimension drawing Wilo Catalogue A2 - <strong>Glanded</strong> pumps DigiCon DigiCon-A DigiCon-A TOP-E TOP-ED 87 33 58 RS 485 15 10 Bus Controller CAN Bus Controller DigiCon DigiCon-A DigiCon-A IP-E IL-E 14 14 8 46 8 90 LON 217 Planning Guide Energy-saving pumps Standard pumps Special In-line <strong>Pumps</strong> Switching and Control Devices Pump Management Systems
Page 1 and 2:
Catalogue Heating, Air-Conditioning
Page 3 and 4:
Contents Wilo Catalogue A2 - Glande
Page 5 and 6:
General Notes and Abbreviations Not
Page 7 and 8:
Planning Guide Maintained pressure
Page 9 and 10:
Planning Guide Mechanical seal A me
Page 11 and 12:
Planning Guide This can take the fo
Page 13 and 14:
Planning Guide Principle of operati
Page 15 and 16:
Energy-Saving Pumps Contents Energy
Page 17 and 18:
Energy-Saving Pumps Single-head pum
Page 19 and 20:
Energy-Saving Pumps Twin-head pumps
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Energy-saving pumps Single-head pum
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Energy-saving pumps Twin-head pumps
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Standard Pumps Contents Standard Pu
Page 69 and 70:
Standard Pumps Single-head pumps In
Page 71 and 72:
Standard Pumps Double pumps In-line
Page 73 and 74:
Standard Pumps In-line pumps Techni
Page 75 and 76:
Standard Pumps Single-head pumps (H
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Standard Pumps Twin-head pumps (Hea
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Special In-line Pumps Contents Spec
Page 151 and 152:
Special In-line Pumps Single-head p
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166: Special In-line Pumps Single-Head P
Page 167 and 168: Switching and Control Devices Conte
Page 169 and 170: Switching and Control Devices Plann
Page 171 and 172: Switching and Control Devices Wilo-
Page 193 and 194: Terminal Diagrams Wilo-CRn, Wilo-CR
Page 199 and 200: Pump Management Systems Wilo-Contro
Page 215: Pump Management Systems Wilo-Contro
Page 219 and 220: Pumpen Intelligenz. Worldwide the n
show all

Glanded Pumps - THERMO-ECO-ENGINEERING úvod

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?