SDM-8400 HIG.book - Comtech EF Data

More documents

Recommendations

Info

NetPerformer SDM-8400 Hardware Installation Guide 3.1 About Unpacking the Unit This chapter outlines preparatory steps that should be executed before you install and configure the SDM-8400: • Selecting a location (“Selecting a Location” on page 3-2) • Preparing the site (“Preparing the Site” on page 3-4). 3.2 Selecting a Location 3.2.1 Size Requirements To ensure that the SDM-8400 functions properly, you should install the unit in an appropriate location which satisfies certain criteria for size, connection distance and ambient environment. 3.2.2 Distance Requirements Figure 3-1: Front View of the SDM-8400 Caution: Unit must be installed in a restricted access location. • Select a standard 19" (48 cm) equipment rack or a hard, flat surface that is: - Capable of supporting the combined weight of the SDM-8400, its cabling and attached equipment - Near an easily accessible AC power socket. • To ensure proper ventilation of the SDM-8400, leave 2 inches (5 cm) of unobstructed space around the unit chassis. • Ensure that a sufficient number of shelves, supports, racks and cabinets are available to safely house all equipment. • The SDM-8400 unit should be no more than 6 feet (approx. 2 meters) away from an easily accessible power outlet: 100-240 VAC, 50/60 Hz. 3-2 Memotec
3.2.3 Environmental Requirements Unpacking • The maximum length of user equipment connections is relative to the serial (WAN/user) port speed: Serial port speed 6 Mbps 8 meters (25 feet) 2 Mbps or less 30 meters (100 feet) Maximum distance from serial port to connected equipment Figure 3-2: Distance from serial port to connected equipment For trouble-free operation the location of the SDM-8400 must satisfy the following environmental criteria: • Operating temperature: 0�C to 45�C (32�F to 113�F) • Storage temperature: -20�C to 65�C (-4�F to 149�F) • Relative humidity: 10% to 90%, non-condensing • Maximum operating altitude: 3048 meters (10 000 feet) • Ventilation requirement: leave 5 cm (2 inches) of unobstructed space around the unit. Memotec 3-3
Page 1 and 2: NetPerformer ® SDM-8400 Hardware I
Page 3 and 4: Contents Chapter 1: Preface. . . .
Page 5 and 6: Chapter 6: Troubleshooting . . . .
Page 7 and 8: List of Figures Location of the Pro
Page 9 and 10: List of Tables System status LED st
Page 11 and 12: Preface 1 Memotec 1-1
Page 13 and 14: 1.2 About this Document 1.2.1 Audie
Page 15 and 16: 1.2.5 ACTView 3000 Document Set 1.2
Page 17 and 18: 1.3.2 Providing Product Numbers to
Page 19 and 20: 1.4 About HyperTerminal Preface The
Page 21 and 22: Compliance Information 2 Memotec In
Page 23 and 24: 2.2 Compliance and Regulatory State
Page 25 and 26: 2.2.2 Marking Compliance Informatio
Page 27 and 28: 2.3 Environmental Information 2.3.1
Page 29 and 30: 2.4 China RoHS Compliance Informati
Page 31: Unpacking 3 Memotec 3-1
Page 35 and 36: Hardware Installation 4 Memotec 4-1
Page 37 and 38: 4.2 Installing the Unit in a Rack A
Page 39 and 40: 4.3 Powering Up the Unit 4.3.1 Conn
Page 41 and 42: 4.4 Connecting the Console Terminal
Page 43 and 44: 4.5 Installing the Licensed Softwar
Page 45 and 46: Product Description 5 Memotec 5-1
Page 47 and 48: Product Description Physical Port P
Page 49 and 50: State Interpretation Blinking Red/A
Page 51 and 52: The following table describes the R
Page 53 and 54: Pin No. Usage Description 2 DTR DTE
Page 55 and 56: 5.6 Rackmount Kit Product Descripti
Page 57 and 58: Troubleshooting 6 Memotec 6-1
Page 59 and 60: Console connection does not work, w
Page 61 and 62: 7 Serial Port and User Equipment Co
Page 63 and 64: Serial Port and User Equipment Conn
Page 65 and 66: 7.5 Custom Serial Cable Specificati
Page 71 and 72: Networking Features 8 Memotec 8-1
Page 73 and 74: 8.3 Data Features Networking Featur
Page 75 and 76: Index A Access methods 3-4 ACT LED
Page 77 and 78: NetPerformer SDM-8400 Hardware Inst

SDM-8400 HIG.book - Comtech EF Data

Create successful ePaper yourself

Delete template?

Save as template?