SDM-8400 HIG.book - Comtech EF Data

More documents

Recommendations

Info

NetPerformer SDM-8400 Hardware Installation Guide 5.3 Ethernet Port 5.3.1 Port • 1 fully routed Ethernet IEEE 802.3 LAN interface • RJ-45 10/100BaseT connector • Can be configured with 2 IP addresses • Auto-detect speed, 10 or 100 Mbps • Frame types: Ethernet II, IEEE 802.2, 802.3, SNAP • Ethernet interface: Ethernet II and IEEE 802.2, 802.3 • Standards: IP RIP V1/V2 or Static, OSPF, NAT, IP Multicast IGMP V1/V2 PIM- DM, BOOTP/DHCP Relay, DHCP client, IPX RIP and SAP, LLC2, 802.1p/q prioritization and VLAN, 802.1D Spanning Tree Protocol (STP), MAC Layer • Filter Criteria: Based on protocol, address (source, destination or SAP) or custom filtering. For information on connecting to the LAN hub, refer to “Connecting the LAN Hub” on page 4-9. 5.3.2 LAN Port Status LEDs 5.3.3 LAN Cable RJ-45 Connector for Ethernet LAN Port Two LAN status indicators are located below the Ethernet port on the rear panel of the SDM-8400 chassis (refer to Table 5-1). These LEDs indicate the following: • LNK: Goes on when the LAN connection passes the Link Integrity test. In addition, the LED color indicates the LAN speed: - Amber: Link integrity at 100 Mbps - Green: Link integrity at 10 Mbps - Off: No link integrity signal detected. • ACT: Goes on (green) when there is activity on the LAN port (LAN traffic transmitted or received). The Ethernet LAN port has an RJ-45 female connector to attach a LAN cable. Select a standard LAN cable with RJ-45 connectors at both ends. The RJ-45 female connector marked ETH on the rear panel of the SDM-8400 provides a physical LAN port for attachment to the local LAN hub (10/100Base-T, MDI connection). 5-6 Memotec
The following table describes the RJ-45 pinout for the LAN port. Pin No. Usage Description 1 TX+ Transmit (+) Output 2 TX- Transmit (-) Output 3 RX+ Receive (+) Input 4 – (not used) 5 – (not used) 6 RX- Receive (-) Input 7 – (not used) 8 – (not used) Table 5-5: RJ-45 pinout for Ethernet LAN port Product Description Memotec 5-7
Page 1 and 2: NetPerformer ® SDM-8400 Hardware I
Page 3 and 4: Contents Chapter 1: Preface. . . .
Page 5 and 6: Chapter 6: Troubleshooting . . . .
Page 7 and 8: List of Figures Location of the Pro
Page 9 and 10: List of Tables System status LED st
Page 11 and 12: Preface 1 Memotec 1-1
Page 13 and 14: 1.2 About this Document 1.2.1 Audie
Page 15 and 16: 1.2.5 ACTView 3000 Document Set 1.2
Page 17 and 18: 1.3.2 Providing Product Numbers to
Page 19 and 20: 1.4 About HyperTerminal Preface The
Page 21 and 22: Compliance Information 2 Memotec In
Page 23 and 24: 2.2 Compliance and Regulatory State
Page 25 and 26: 2.2.2 Marking Compliance Informatio
Page 27 and 28: 2.3 Environmental Information 2.3.1
Page 29 and 30: 2.4 China RoHS Compliance Informati
Page 31 and 32: Unpacking 3 Memotec 3-1
Page 33 and 34: 3.2.3 Environmental Requirements Un
Page 35 and 36: Hardware Installation 4 Memotec 4-1
Page 37 and 38: 4.2 Installing the Unit in a Rack A
Page 39 and 40: 4.3 Powering Up the Unit 4.3.1 Conn
Page 41 and 42: 4.4 Connecting the Console Terminal
Page 43 and 44: 4.5 Installing the Licensed Softwar
Page 45 and 46: Product Description 5 Memotec 5-1
Page 47 and 48: Product Description Physical Port P
Page 49: State Interpretation Blinking Red/A
Page 53 and 54: Pin No. Usage Description 2 DTR DTE
Page 55 and 56: 5.6 Rackmount Kit Product Descripti
Page 57 and 58: Troubleshooting 6 Memotec 6-1
Page 59 and 60: Console connection does not work, w
Page 61 and 62: 7 Serial Port and User Equipment Co
Page 63 and 64: Serial Port and User Equipment Conn
Page 65 and 66: 7.5 Custom Serial Cable Specificati
Page 71 and 72: Networking Features 8 Memotec 8-1
Page 73 and 74: 8.3 Data Features Networking Featur
Page 75 and 76: Index A Access methods 3-4 ACT LED
Page 77 and 78: NetPerformer SDM-8400 Hardware Inst

SDM-8400 HIG.book - Comtech EF Data

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?