SDM-8400 HIG.book - Comtech EF Data

More documents

Recommendations

Info

NetPerformer SDM-8400 Hardware Installation Guide 7.1 Serial Port 4 or 8 serial ports for WAN/user traffic: • HD-26 female connector • Asynchronous speeds: 300 bps to 115.2 Kbps • Synchronous speeds: 1200 bps to 6 Mbps (6144 Kbps) without data compression; 896 Kbps link port maximum speed with data compression For further details concerning the serial port, turn to “WAN/User Port Specifications” on page 7-4. 7.2 Custom HD-26 Cable The serial ports require a custom-made HD-26 male cable, which can be ordered from Memotec or your NetPerformer distributor. For ordering information, refer to “Sales Contacts” on page 1-2. The required cable depends on the interface and gender of the attached equipment. Twelve custom HD-26 serial cable models are available: • V.35/V.11 DCE, V.35/V.11 DTE (for details see “V.35/V.11 Cables” on page 7-5) • TIA-232 (V.24) DCE, TIA-232 (V.24) DTE (see “TIA-232 (V.24) Cables” on page 7-5) • X.21 DCE, X.21 DTE, with 4-40 screw on the DB-25 connector (see “X.21 Cables” on page 7-5) • X.21 EU DCE, X.21 EU DTE, with metric M3 screw on the DB-15 connector (see “X.21 EU Cables” on page 7-6) • TIA-449 (V.36) DCE, TIA-449 (V.36) DTE (see “TIA-449 (V.36) Cables” on page 7-6) • TIA-530 DCE, TIA-530 DTE (see “TIA-530 Cables” on page 7-6). All cables are 1.8 meters (6 feet) long, and have HD-26 male connectors at one end. At the other end: • A male connector indicates that the cable is DTE and that it connects to a DCE device (a modem, for example). • A female connector indicates that the cable is DCE and that it connects to a DTE device (a terminal or another NetPerformer, for example). NOTE: When ordering a cable for the serial port, make sure you specify the correct gender. 7-2 Memotec
Serial Port and User Equipment Connection The HD-26 female connector automatically detects the interface and gender according to the type of HD-26 custom cable that is installed. For example, with a V.35/V.11 DTE cable the port will select V.35/V.11 electrical characteristics and DTE. Software configuration of these characteristics is thus not required. For details concerning the custom serial cable, refer to “Custom Serial Cable Specifications” on page 7-5. 7.3 Connecting the User Equipment To connect the user equipment to a serial port: 1. Locate the HD-26 custom cable that is appropriate for: • The device you are attaching: DTE or DCE • The interface you want to use: V.35/V.11, TIA-232 (V.24), X.21, X.21 EU, TIA- 449 (V.36) or TIA-530. 2. Connect the male end of the HD-26 cable to the SDM-8400 serial port. 3. Connect the other end of the cable to the user device (CSU/DSU, modem, router, front end processor, etc.). Caution: Do not connect a data port (WAN/user) to a host, PU, or Frame Relay device until you have configured the port protocol via the software. Refer to the NetPerformer System Reference for details. 7.3.1 Activating the User Equipment Connection To activate the user equipment connection: 1. Configure all parameters and options for the connection. Refer to the NetPerformer System Reference, which is included on the NetPerformer Documentation CD. 2. Activate a data connection by bringing up the connected user equipment. 3. Activate a voice connection by dialing a speed dial number to place a call. 4. Check the status of the NetPerformer, its connections and all active channels, ports, PVCs and SVCs by executing the statistics commands (refer to the NetPerformer System Reference for details). Memotec 7-3
Page 1 and 2:
NetPerformer ® SDM-8400 Hardware I
Page 3 and 4:
Contents Chapter 1: Preface. . . .
Page 5 and 6:
Chapter 6: Troubleshooting . . . .
Page 7 and 8:
List of Figures Location of the Pro
Page 9 and 10:
List of Tables System status LED st
Page 11 and 12: Preface 1 Memotec 1-1
Page 13 and 14: 1.2 About this Document 1.2.1 Audie
Page 15 and 16: 1.2.5 ACTView 3000 Document Set 1.2
Page 17 and 18: 1.3.2 Providing Product Numbers to
Page 19 and 20: 1.4 About HyperTerminal Preface The
Page 21 and 22: Compliance Information 2 Memotec In
Page 23 and 24: 2.2 Compliance and Regulatory State
Page 25 and 26: 2.2.2 Marking Compliance Informatio
Page 27 and 28: 2.3 Environmental Information 2.3.1
Page 29 and 30: 2.4 China RoHS Compliance Informati
Page 31 and 32: Unpacking 3 Memotec 3-1
Page 33 and 34: 3.2.3 Environmental Requirements Un
Page 35 and 36: Hardware Installation 4 Memotec 4-1
Page 37 and 38: 4.2 Installing the Unit in a Rack A
Page 39 and 40: 4.3 Powering Up the Unit 4.3.1 Conn
Page 41 and 42: 4.4 Connecting the Console Terminal
Page 43 and 44: 4.5 Installing the Licensed Softwar
Page 45 and 46: Product Description 5 Memotec 5-1
Page 47 and 48: Product Description Physical Port P
Page 49 and 50: State Interpretation Blinking Red/A
Page 51 and 52: The following table describes the R
Page 53 and 54: Pin No. Usage Description 2 DTR DTE
Page 55 and 56: 5.6 Rackmount Kit Product Descripti
Page 57 and 58: Troubleshooting 6 Memotec 6-1
Page 59 and 60: Console connection does not work, w
Page 61: 7 Serial Port and User Equipment Co
Page 65 and 66: 7.5 Custom Serial Cable Specificati
Page 67 and 68: Serial Port and User Equipment Conn
Page 69 and 70: Serial Port and User Equipment Conn
Page 71 and 72: Networking Features 8 Memotec 8-1
Page 73 and 74: 8.3 Data Features Networking Featur
Page 75 and 76: Index A Access methods 3-4 ACT LED
Page 77 and 78: NetPerformer SDM-8400 Hardware Inst
show all

SDM-8400 HIG.book - Comtech EF Data

Create successful ePaper yourself

Delete template?

Save as template?