SDM-8400 HIG.book - Comtech EF Data

More documents

Recommendations

Info

NetPerformer SDM-8400 Hardware Installation Guide 2. Power the console terminal on or start your console terminal emulation program. Take note of: • “Important Console and Modem Settings for Startup” on page 4-7 • “Concerning HyperTerminal Connections” on page 8-1. 3. When you see the prompt Type to connect, press the key on the console terminal keyboard several times, until the SDM-8400 responds with a prompt for the user login. 4. Enter the administrator login: ADMIN. NOTE: This is the default login. Additional user logins can be defined. For details, refer to the chapter Controlling Access to the NetPerformer in the Quick Configuration fascicle of the NetPerformer System Reference. 5. Enter the password for this login. The default password for the administrator login is SETUP. When the password is entered correctly, the SDM-8400 sends the product banner to the console screen, as in this example: LOGIN:ADMIN PASSWORD:***** ACCEPTED SDM-8400 vx.x.x Memotec Inc. (c) 2007 Signaling Engine x.x.x Console connected on port CSL B302417> 6. Enter the Display Alarms (DA) command at the NetPerformer console command line to verify that your unit is problem free. In particular, look for any alarm messages that indicate Call Technical Support. 4-8 Memotec
4.5 Installing the Licensed Software Options Hardware Installation Execute the Product License Status (PLS) command at the NetPerformer console command line to install all licensed software options you have purchased for your SDM- 8400 unit. Each licensed option includes a Software Licensing Agreement, which can be found in the product package. You must agree to the terms and conditions of this agreement before loading the software. Each NetPerformer unit participating in the software application must be installed with a separate software license. 4.5.1 Software License Key The Memotec Software License Key is a traceable number that is used to activate the licensed software option. • This number is printed on an adhesive label on the cover of the licensed software option product package • Enter this number during execution of the PLS command to activate the software license • You must then execute Reset Unit (RU) command to apply the new license. For details concerning installation of licensed software options, refer to the Software Installation and Licensing module of the NetPerformer System Reference, which is included on the NetPerformer Documentation CD in the product package. 4.6 Connecting the LAN Hub NOTE: You must provide a standard straight through Ethernet 802.3 LAN cable (10/ 100BaseT, RJ-45M to RJ-45M) for connection to the LAN. A LAN cable is not provided with the SDM-8400 product package. To connect the SDM-8400 unit to a LAN hub: 1. Connect one end of the LAN cable to the SDM-8400 Ethernet LAN port, labelled ETH on the rear panel. Refer to Figure 5-1 on “Rear View of the SDM-8400 UAC (8port version)” on page 5-2. 2. Connect the other end of the LAN cable to one of the 10/100BaseT ports on your local LAN hub. 3. The link is up when the LNK LED is on. The LED color indicates the speed of the LAN connection: • Amber: 100 Mbps • Green: 10 Mbps. Memotec 4-9
Page 1 and 2: NetPerformer ® SDM-8400 Hardware I
Page 3 and 4: Contents Chapter 1: Preface. . . .
Page 5 and 6: Chapter 6: Troubleshooting . . . .
Page 7 and 8: List of Figures Location of the Pro
Page 9 and 10: List of Tables System status LED st
Page 11 and 12: Preface 1 Memotec 1-1
Page 13 and 14: 1.2 About this Document 1.2.1 Audie
Page 15 and 16: 1.2.5 ACTView 3000 Document Set 1.2
Page 17 and 18: 1.3.2 Providing Product Numbers to
Page 19 and 20: 1.4 About HyperTerminal Preface The
Page 21 and 22: Compliance Information 2 Memotec In
Page 23 and 24: 2.2 Compliance and Regulatory State
Page 25 and 26: 2.2.2 Marking Compliance Informatio
Page 27 and 28: 2.3 Environmental Information 2.3.1
Page 29 and 30: 2.4 China RoHS Compliance Informati
Page 31 and 32: Unpacking 3 Memotec 3-1
Page 33 and 34: 3.2.3 Environmental Requirements Un
Page 35 and 36: Hardware Installation 4 Memotec 4-1
Page 37 and 38: 4.2 Installing the Unit in a Rack A
Page 39 and 40: 4.3 Powering Up the Unit 4.3.1 Conn
Page 41: 4.4 Connecting the Console Terminal
Page 45 and 46: Product Description 5 Memotec 5-1
Page 47 and 48: Product Description Physical Port P
Page 49 and 50: State Interpretation Blinking Red/A
Page 51 and 52: The following table describes the R
Page 53 and 54: Pin No. Usage Description 2 DTR DTE
Page 55 and 56: 5.6 Rackmount Kit Product Descripti
Page 57 and 58: Troubleshooting 6 Memotec 6-1
Page 59 and 60: Console connection does not work, w
Page 61 and 62: 7 Serial Port and User Equipment Co
Page 63 and 64: Serial Port and User Equipment Conn
Page 65 and 66: 7.5 Custom Serial Cable Specificati
Page 71 and 72: Networking Features 8 Memotec 8-1
Page 73 and 74: 8.3 Data Features Networking Featur
Page 75 and 76: Index A Access methods 3-4 ACT LED
Page 77 and 78: NetPerformer SDM-8400 Hardware Inst

SDM-8400 HIG.book - Comtech EF Data

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?