SDM-8400 HIG.book - Comtech EF Data

More documents

Recommendations

Info

NetPerformer SDM-8400 Hardware Installation Guide 7.4 WAN/User Port Specifications • 1 built-in serial port, configurable as user or link, supporting V.35/V.11, TIA-232 (V.24), X.21, X.21 EU, TIA-449 (V.36) and TIA-530 interfaces • Maximum speed without compression: 6 Mbps (6144 Kbps) NOTE: For a port with INTERNAL clocking, if the port speed is configured higher than 2 Mbps (2048 Kbps), the clock speed will be 3 Mbps (3072 Kbps) or 6 Mbps (6144 Kbps), whichever is closer to the configured speed. For EXTERNAL clocking all port speeds are supported. • Link port maximum speed with compression: 896 Kbps • HD-26 female connectors, gender and interface autodetect from custom HD-26 cables: V.35 DCE, V.35 DTE, X.21 DCE, X.21 DTE, X.21 EU DCE, X.21 EU DTE, TIA-232 DCE, TIA-232 DTE, TIA-449 DCE, TIA-449 DTE, TIA-530 DCE, TIA-530 DTE • Circuits: either leased, switched or Frame Relay • Coding: NRZI or NRZ • WAN port protocols: synchronous full-duplex HDLC, Frame Relay (FR-USER for network connection), RFC-1490 • Synchronous user port protocols: HDLC, Synchronous PPP • Frame Relay protocols: Frame Relay User (FR-USER), Frame Relay Network (FR-NET), RFC-1490, UNI-DTE, UNI-DCE • Frame Relay management: LMI, ANSI TI.617/Annex D, ITU-T Q.933/Annex A, CLLM or disabled • PVC switching: 300 PVCs, automatic DLCI discovery • SVCs: Frame Relay telephony applications, one SVC per voice call. • SNA: SDLC, LAN or Frame Relay RFC1490 (BAN, BNN); SDLC spoofing of up to 64 PUs, type 1, 2.0, 2.1 and 4/5, local SDLC and LLC2 spoofing, SDLC-to- LLC2 conversion • Asynchronous user port protocols: ENQ/ACK, XON/XOFF, CTS/DTR, Transparent, Reliable, Asynchronous PPP 7-4 Memotec
7.5 Custom Serial Cable Specifications 7.5.1 V.35/V.11 Cables 7.5.2 TIA-232 (V.24) Cables 7.5.3 X.21 Cables Serial Port and User Equipment Connection NOTE: In the following sections the Ordering part number is required for ordering extra cables. The Stock number is printed on the cable. • HD-26 male connector at one end for connection to the SDM-8400 serial port • ISO-2593 female (DCE) or male (DTE) connector at the other end for connection to the V.35/V.11 equipment • Use the DCE cable for connection to a male connector on the V.35/V.11 equipment (typically a DTE device) Ordering part number 161-0893-001, Stock number 502-0940-006. • Use the DTE cable for connection to a female connector on the V.35/V.11 equipment (typically a DCE device). Ordering part number 161-0894-001, Stock number 502-0941-006. • HD-26 male connector at one end for connection to the SDM-8400 serial port • DB-25 female (DCE) or male (DTE) connector at the other end for connection to the TIA-232 (V.24) equipment • Use the DCE female cable for connection to a male connector on the TIA-232 (V.24) equipment (typically a DTE device) Ordering part number 161-0897-001, Stock number 502-0944-006. • Use the DTE male cable for connection to a female connector on the TIA-232 (V.24) equipment (typically a DCE device) Ordering part number 161-0898-001, Stock number 502-0945-006. NOTE: An X.21 cable has a 4-40 screw on the DB-15 connector. • HD-26 male connector at one end for connection to the SDM-8400 serial port • DB-15 female (DCE) or male (DTE) connector at the other end for connection to the X.21 equipment Memotec 7-5
Page 1 and 2:
NetPerformer ® SDM-8400 Hardware I
Page 3 and 4:
Contents Chapter 1: Preface. . . .
Page 5 and 6:
Chapter 6: Troubleshooting . . . .
Page 7 and 8:
List of Figures Location of the Pro
Page 9 and 10:
List of Tables System status LED st
Page 11 and 12:
Preface 1 Memotec 1-1
Page 13 and 14: 1.2 About this Document 1.2.1 Audie
Page 15 and 16: 1.2.5 ACTView 3000 Document Set 1.2
Page 17 and 18: 1.3.2 Providing Product Numbers to
Page 19 and 20: 1.4 About HyperTerminal Preface The
Page 21 and 22: Compliance Information 2 Memotec In
Page 23 and 24: 2.2 Compliance and Regulatory State
Page 25 and 26: 2.2.2 Marking Compliance Informatio
Page 27 and 28: 2.3 Environmental Information 2.3.1
Page 29 and 30: 2.4 China RoHS Compliance Informati
Page 31 and 32: Unpacking 3 Memotec 3-1
Page 33 and 34: 3.2.3 Environmental Requirements Un
Page 35 and 36: Hardware Installation 4 Memotec 4-1
Page 37 and 38: 4.2 Installing the Unit in a Rack A
Page 39 and 40: 4.3 Powering Up the Unit 4.3.1 Conn
Page 41 and 42: 4.4 Connecting the Console Terminal
Page 43 and 44: 4.5 Installing the Licensed Softwar
Page 45 and 46: Product Description 5 Memotec 5-1
Page 47 and 48: Product Description Physical Port P
Page 49 and 50: State Interpretation Blinking Red/A
Page 51 and 52: The following table describes the R
Page 53 and 54: Pin No. Usage Description 2 DTR DTE
Page 55 and 56: 5.6 Rackmount Kit Product Descripti
Page 57 and 58: Troubleshooting 6 Memotec 6-1
Page 59 and 60: Console connection does not work, w
Page 61 and 62: 7 Serial Port and User Equipment Co
Page 63: Serial Port and User Equipment Conn
Page 67 and 68: Serial Port and User Equipment Conn
Page 69 and 70: Serial Port and User Equipment Conn
Page 71 and 72: Networking Features 8 Memotec 8-1
Page 73 and 74: 8.3 Data Features Networking Featur
Page 75 and 76: Index A Access methods 3-4 ACT LED
Page 77 and 78: NetPerformer SDM-8400 Hardware Inst
show all

SDM-8400 HIG.book - Comtech EF Data

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?