Mod. 1092 Sch./Ref. 1092/602

More documents

Recommendations

Info

Option Value DescriptionLanguage ENGLISH Menus are only in English.Dome Information Product information menu (see par. 4.5.1).Display Informations Display menu (see par. 4.5.2).Control Options Main programming menu (see par. 4.5.3).Diagnostic Options Secondary programming menu (see par. 4.5.4).Camera OptionsFunction ProgrammingMenu used to configure the text associated to the dome (see par.4.5.5).Menu concerning Preset, Vector Scan, Pattern, Motion andAlarms programming and storing procedures.4.5.1 PRODUCT INFORMATION MENUSelect from the first level menu to have information about module, protocol, baudrate, dome address, version.Dome InformationCameraSAMSUNGProtocolPelco DBaudrate 9600Dome NO 3Version X.XXIRIS CLOSE to ExitThis information can not be changed in this menu.4.5.2 Display optionsThe menu allows to enable/disable the messages which must appear in THERA 5functions.Display OptionsCoordinates ONStart-Up Scr Msg ONIRIS CLOSE To ExitOption Value DescriptionCOORDINATES ON/OFF Display of pan/tilt coordinates of shown images enabled/disabled.START-UP SCR MSGON/OFFDisplay of product information at dome power-up enabled/disabled(see par. 4.5.1).DS<strong>1092</strong>-090 64
4.5.3 Settings of main programming procedures via the menu (Control Options)From the first level menu, select and its submenus to access the main menus forprogramming THERA 5.CONTROL OPTIONS>1 Auto Flip ON2 Proportional Speed ON3 Pan Reverse OFF4 Tilt Reverse OFF5 Vector Scan Still OFF6 Auto Focus PTZ7 Auto AE PTZ8 VectorScan AF ON9 +2 Tilt Limit OFF10 Speed limit OFFIRIS CLOSE to ExitOption Value DescriptionAuto FlipProportional SpeedOn/offON/OFFIf this mode is active (ON), the dome can follow the trajectory ofan object that moves and goes under the dome, only with thevertical movement of the joystick. This because the dome, when invertical position, performs an automatic pan movement of 180degrees in order to reach a position where the tilt movements areagain possible.If this mode is active (ON), pan and tilt speed, configured with thekeypad, is proportional to the configured zoom. Therefore themotion speed is reduced when the zoom increases.Pan RiverseTilt RiverseON/OFFON/OFFVectorScan Still ON/OFF FUNCTION NOT ENABLEDIf this mode is active (ON), joystick commands for pan function arereversed.If this mode is active (ON), joystick commands for tilt function arereversed.Auto FocusAuto AEON/OFF/PTZ/ZON/OFF/PTZ/ZIf activated with ON, the dome will automatically control the imagefocus. If activated with PTZ, the dome will focus images only whenusing Pan, Tilt and Zoom functions. If activated with Z, the domewill focus images only when using the zoom function.If activated with ON, the dome will automatically control the imageexposure. If activated with PTZ, the dome will perform this controlonly when using Pan, Tilt and Zoom functions. If activated with Z,the dome will perform this control only when using the zoomfunction.VectorScan AF ON/OFF FUNCTION NOT ENABLED+2 Tilt Limit ON/OFFSpeed limitON/OFFIf activated with ON, the limit of dome tilt will increase of 2degrees, changing from 0° to -2°.If activated with ON , this function halves the previously configureddome speed.DS<strong>1092</strong>-090 65
Page 1 and 2:
Mod.1092DS1092-090THERA 5 MINIDOME
Page 3 and 4:
1 INFORMAZIONI GENERALICaro cliente
Page 6 and 7:
3 PROCEDURE DI INSTALLAZIONEQuesta
Page 8 and 9:
Bloccare la staffa alla dome utiliz
Page 10 and 11:
Eseguire il collegamento dell’ali
Page 12 and 13:
COLLEGAMENTICollegare il cavo in do
Page 14 and 15: 4 MODALITÀ DI FUNZIONAMENTO4.1 FUN
Page 16 and 17: 4.3 SELEZIONE DELLA DOMEPrima di po
Page 18 and 19: 4.4.5 IMPOSTAZIONE E RICHIAMO DI PO
Page 20 and 21: 4.5.3 Impostazioni da menu relative
Page 22 and 23: CAM TITLEWHITE BALBACKLIGHTOpzione
Page 24 and 25: 4.5.7.3 Backlight - BLC - compensaz
Page 26 and 27: D-ZOOMSelezionando D-ZOOM è possib
Page 28 and 29: SENS-UP (DSS) - VARIAZIONE DELLA SE
Page 30 and 31: Selezionando LEVEL e premendo i tas
Page 32 and 33: Opzione Valore SpiegazioneNumber 1
Page 34 and 35: NAMESelezionando NAME e premendo OP
Page 36 and 37: 4.5.8.5 Masking zone- zona di masch
Page 38 and 39: Opzione Valore SpiegazioneActionNum
Page 40 and 41: Opzione Valore SpiegazioneActionNum
Page 42 and 43: Assegnazione dell’indirizzo della
Page 44 and 45: 5 COMANDI SPECIALII comandi special
Page 46 and 47: Caratteristiche meccanicheVelocità
Page 48 and 49: 1 GENERAL INFORMATIONDear Customer,
Page 50 and 51: RepairsDo not attempt to repair the
Page 52 and 53: 3.2.1 WALL MOUNTINGBefore starting
Page 54 and 55: WALL MOUNTING WITH POWER BOX REF. 1
Page 56 and 57: Put the provided junction ring in t
Page 58 and 59: 3.2.2 REQUIREMENTS FOR CONNECTION C
Page 60 and 61: 4.2.1 KEYPAD REF. 1092/620 COMMAND
Page 62 and 63: The AUTO FLIP function allows to fo
Page 66 and 67: 4.5.4 SETTINGS OF MAIN PROGRAMMING
Page 68 and 69: 4.5.7.2 White bal - white balancing
Page 70 and 71: MODESelect MODE to choose among MAN
Page 72 and 73: IRISSelect IRIS and choose between
Page 74 and 75: DAY/NIGHT - DOME OPERATION CHANGE A
Page 76 and 77: 4.5.8.1 Preset - storage of dome po
Page 78 and 79: Dwell - is the dwell time before th
Page 80 and 81: Tilt Start POS 0,0 ÷ 359,9 ÷ 0,0
Page 82 and 83: PARK ACTIONThe PARK ACTION is the a
Page 84 and 85: 4.5.8.7 Alarm in programming - acti
Page 86 and 87: Dome address assignment with pelco
Page 88 and 89: 5 SPECIAL COMMANDSThe below describ
Page 90 and 91: NOTE...............................
Page 92: DS1092-090FILIALI20151 MILANO - V.
show all

Mod. 1092 Sch./Ref. 1092/602

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?